Kreg KPHA740 Manual de usuario

English 2

French 11

Spanish 21

OWNER’S MANUAL

We’re here to help.

We want you to have an exceptional project building experience.

If you have questions or need support, please get in touch.

1-800-447-8638 | [email protected]

Tell us about your experience.

Your opinion counts. And we’re always looking for ways to

improve. Share your feedback so we can keep growing and

innovating for you. www.kregtool.com/feedback

WARNING Every user must read and follow instructions and safety

precautions in this manual. Failure to do so could result in serious injury.

Save manual for future reference.

Kreg Plug Cutter Drill Guide Kit

KPHA740

Safety Precautions

WARNING Before using a power tool with this product, read and follow the

tool manufacturer’s instructions and safety precautions in addition to the safety

precautions below to reduce the risk of serious injury from hazards such as re,

electric shock, or rotating drill bit.

■Always wear personal protective equipment recommended by the

manufacturer of the power tool you are using, such as eye, hearing, or

respiratory protection.

■The drill bit is sharp. Handle with care.

■Do not allow familiarity gained from frequent use of your tools to replace

safe work practices. A moment of carelessness is sufcient to cause

serious injury.

■Avoid awkward hand positions where a sudden slip could cause contact

with the rotating bit.

■When drilling, always ensure that the workpiece is clamped securely. It is

dangerous to hold the workpiece in place by hand.

WARNING Do not operate this tool or any machinery while under the inuence

of drugs, alcohol, or medications.

WARNING This product can expose you to chemicals including Acrylonitrile

and other chemicals, which are known to the State of California to cause

cancer and reproductive harm. For more information go to

www.P65Warnings.ca.gov.

Table of Contents

Safety Precautions . . . . . . . . . 2

Pre-Installation/Pre-Assembly. . . 3

Assembly/Setup . . . . . . . . . .4

Operation – Drill the Plugs . . . . . 6

Operation – Cut the Plugs from the

Blank . . . . . . . . . . . . . . . .7

Operation – Plug the Pocket Holes7

Accessories . . . . . . . . . . . . 8

Pre-Installation/Pre-Assembly

Review this section before you begin. Ensure you have all parts listed below.

If any item appears missing or lost, do not use this product. Contact Technical

Support or return product to place of purchase.

Part Description

A KPHA740 Plug Cutter Drill Guide

B Plug Cutter Bit (for standard size pocket holes)

C Plug Cutter Stop Collar

D Hex Wrench

Assembly/Setup

a. Remove existing drill guide from the Kreg Jig 720 by squeezing the tabs

(1) on both sides and lifting forward and up to remove the drill guide from

the carriage of the Kreg Jig.

b. Insert the Plug Cutter Drill Guide (A) into the carriage by squeezing the

tabs (1) on both sides of the drill guide carriage, inserting the bottom tab

of the Plug Cutter Drill Guide (A) into the slot on the Kreg Jig carriage and

pressing the top of the Plug Cutter Drill Guide (A) into place.

Assembly/Setup (continued)

c. Slide the Plug Cutter Stop Collar (C) onto the Plug Cutter Bit (B) until

it rests on the bit shoulder. Tighten the Plug Cutter Stop Collar (C) set

screw with the hex wrench (D).

Note Kreg recommends usng a corded drill for drilling pocket hole plugs.

Higher speeds will produce better quality pocket hole plugs, but also increase

the heat produced, so it may be necessary to adjust your production rate to

allow time for the bit to cool.

Operation – Drill the Plugs

a. Cut the plug blanks 3-1/4" (83 mm) long in the intended direction of the

plug. For best results, use leftover scraps from your project to match

color and grain pattern.

b. Set the drill on the highest speed.

c. Clamp the blank securely in the Kreg Jig KPHJ720.

d. Insert the Plug Cutter Bit (B) into the Plug Cutter Drill Guide (A) holding

the Plug Cutter bit about 1/4" (6 mm) from the workpiece.

e. Start the drill and let it come up to full speed. Then, using light pressure

and a slow feed rate, slowly push the Plug Cutter Bit (B) until the stop

collar (C) contacts the Plug Cutter Drill Guide (A).

f. Withdraw the Plug Cutter Bit (B) from the Plug Cutter Drill Guide (A) taking

care as the Plug Cutter Bit (B) may be hot.

g. Release the clamp, reposition the blank, re-clamp securely, and repeat

for each plug.

Operation – Cut the Plugs from the

Blank

a. Mark a line in location 1 that is 3/16" (5 mm) from the bottom edge of

the plug blank.

b. Apply a strip of masking tape across the plugs to keep them in position

while cutting.

c. Cut along the line at a 15° angle with a band saw, scroll saw, multi-

purpose oscillation tool, or ne-tooth hand saw.

3/16"

(5mm)

15°

Operation – Plug the Pocket Holes

a. Glue plugs in letting approximately 1/16" (2 mm) of the plug protrude.

b. Once glue is dry, sand the plug ush.

Accessories

KPC1040 Kreg Micro Plug Cutting Bit

KPC1060 Kreg HD Plug Cutting Bit

06/2020 104696 V1

EXPLORE. BUILD. SHARE.

We’re makers just like you.

That’s why we love to see what you’re working on.

Share with the community and get inspired!

#madewithKreg

Get free plans, project resources, and more.

kregtool.com and buildsomething.com

Tabla de contenidos

Idiomas:

Otros manuales de Herramientas de Kreg

Kreg

Kreg KMA3220 Manual de usuario

Kreg

Kreg Accu-Cut KMA2700 Manual de usuario

Kreg

Kreg DB55 Manual de operación y mantenimiento

Kreg

Kreg Jig K5 Manual de usuario

Kreg

Kreg KPHJ310 Manual de usuario

Kreg

Kreg Rip-Cut KMA2675 Manual de usuario

Kreg

Kreg r3 Manual de operación y mantenimiento

Kreg

Kreg DB110 Manual de operación y mantenimiento

Kreg

Kreg 700 Series Manual de usuario

Kreg

Kreg Adaptive Cutting System Project Table Kit Manual de usuario

Kreg

Kreg KHI-PULL-INT Manual de usuario

Kreg

Kreg KFPCHB Manual de usuario

Kreg

Kreg KHI-CDIJ Manual de usuario

Kreg

Kreg KCS-DFMT Manual de usuario

Kreg

Kreg Jig R3 Manual de usuario

Kreg

Kreg Adaptive Cutting System Parallel Guides Manual de usuario

Kreg

Kreg K4 Manual de usuario

Kreg

Kreg Jig K4 Manual de usuario

Kreg

Kreg Clamp Vise Manual de usuario

Kreg

Kreg KMA4000 Manual de usuario

Kreg

Kreg KMA3225 Manual de usuario

Kreg

Kreg MINI KREG JIG Manual de usuario

Kreg

Kreg Jig NK7520 Manual de usuario

Kreg

Kreg FOREMAN DB210 Manual de usuario

Manuales populares de Herramientas de otras marcas

Martor

Martor SECUNORM 175 Manual de usuario

ERKCO

ERKCO 1000 Manual de usuario

jbc

jbc N4473 Manual de usuario

FEINMETALL

FEINMETALL FZWZ-SET-001 Manual de usuario

Worx Professional

Worx Professional Sonicrafter WU676 Manual de usuario

Gage Bilt

Gage Bilt GB713SH Manual de usuario

Hilti

Hilti DX 9-ENP Manual de usuario

norbar

norbar NORTRONIC 34399 Manual de usuario

BGS technic

BGS technic 8578 Manual de usuario

Makita

Makita DHR241 Manual de usuario

Motor Guard

Motor Guard JMB-1250 Manual de usuario

Power Adhesives

Power Adhesives 805-12 Manual de usuario

Clemco

Clemco 24189 Manual de usuario

VVG

VVG VNG 903 Series Manual de usuario

Hilti

Hilti FX 3-A Manual de usuario

Grizzly

Grizzly H6472 Manual de usuario

axing

axing BWZ 5-02 Manual de usuario

Dh-Robotics

Dh-Robotics RGI-100 Cómo utilizar