Kramer WP-789R Manual de usuario

WP-789R Quick Start

P/N:

2900- 301299QS

Rev:

Scan for full manual

WP-789R Quick Start Guide

This guide helps you install and use your WP-789R for thefirst time.

Go to www.kramerav.com/downloads/WP-789R to download thelatest user manual and check if firmware

upgrades are available.

Step 1: Check what’s in the box

WP-789R HDMI 4K Wall-Plate Line Receiver

1 Quick start guide

Installation accessories

1 Power adapter and cord

Frame (or frame kit)

Step 2: Get to know your WP-789R

Feature

Function

HDMI™ OUT Connector

Connect to an HDMI acceptor.

IR (Tx1, Tx2) Output, 3-pin

Terminal Block Connectors

Connect to an external IR emitter cable:

Tx1, G: use for fixed 38kHz non-modulated IR signals.

Tx2, G: use for 20-100kHz wide-range modulated IR signals.

STATUS LED

LED Color

HDBT Connected

Source Detected

Acceptor Detected

Blue

Yes

Green

Yes

Yellow

Yes

N/A

White

Device is powered with no detected connections.

STATUS LED is off only when the device does not receive power.

RS-232 (G, Rx, Tx)

3-pin Terminal Block Connector

Connect to an RS-232 port.

Power Supply 2-pin Terminal

Block Connector

Connect to a power supply (if required). Connect GND to GND, +12V to +12V.

Ring Tongue Terminal

Grounding Screw

Connect to grounding wire (optional).

HDBT IN RJ-45 Connector

Connect to the HDBT OUT connector on a transmitter (for example, TP-780T).

The terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.

Step 3: Install the WP-789R

Insert the device into the in-wall box (note that first you need to connect the HDBT cable and power) and connect the parts as

shown in the illustrations below:

EU/UK Version

US-D Version

DECORA® design frames are included in US-D models.

DECORA® is a registered trademark of Leviton Manufacturing Co., Inc.

We recommend that you use any of the following standard 2 gang in-wall junction boxes (or their equivalent):

•US-D: 2 gang US electrical junction boxes.

•EU: 2 gang in-wall junction box, with a cut-hole diameter of 2x68mm and depth that can fit in both the device and the

connected cables (DIN 49073).

•UK: 2 gang in-wall junction box (BS 4662), 135x75mm (W, H) and depth that can fit in both the device and the

connected cables.

•EU/UK: 2 gang on-wall junction box (use the recommended Kramer on-wall box available at

www.kramerav.com/product/WP-789R.).

Step 4: Connect the inputs and outputs

Always switch OFF the power on each device before connecting it to your WP-789R. For best results, we recommend that you

always use Kramer high-performance cables to connect AV equipment to the WP-789R.

Wiring the RJ 45 Connectors

It is recommended that the cable ground shielding be

connected/soldered to the connector shield.

PIN EIA /TIA 568b

Wire Color

Orange / White

Orange

Green / White

Blue

Blue / White

Green

Brown / White

Brown

For optimum range and performance use the recommended Kramer cables available at

www.kramerav.com/product/WP-789R.

Grounding the WP-789R (Optional)

1. Connect the ring tongue terminal to the building grounding point wire (a green-yellow, AWG#18 (0.82mm2) wire,

crimped with a proper hand-tool is recommended).

2. Insert the M3x6 screw through the toothed lock washers and the tongue terminal in the order shown above.

3. Insert the M3x6 screw (with the two toothed lock washers and ring tongue terminal) into the grounding screw hole

and tighten the screw.

Step 5: Connect the power

When accepting power over HDBaseT from a PoE provider (for example, the TP-780T), there is no need to connect the 12V

DC power supply.

Otherwise, connect the 12V power adapter to the device and plug the power supply into the mains electricity.

Safety Instructions

Caution:

There are no operator serviceable parts inside the unit.

Warning:

Use only the Kramer Electronics power supply that is provided with the unit.

Warning:

Disconnect the power and unplug the unit from the wall before installing.

See www.KramerAV.com for updated safety information.

Tabla de contenidos

Otros manuales de Convertidor de medios de Kramer

Kramer

Kramer SD-7401 Manual de usuario

Kramer

Kramer VM-100C Manual de usuario

Kramer

Kramer FC-31xl Manual de usuario

Kramer

Kramer MV-6 Manual de usuario

Kramer

Kramer VM-51 Manual de usuario

Kramer

Kramer KDS-EN6 Manual de usuario

Kramer

Kramer DigiTOOLS 7408 Manual de usuario

Kramer

Kramer VP-740 ProScale Manual de usuario

Kramer

Kramer FC-5000 Manual de usuario

Kramer

Kramer VP-413XL Manual de usuario

Kramer

Kramer FC-4001 Manual de usuario

Kramer

Kramer VA-1VGA Manual de usuario

Kramer

Kramer VP-417 Manual de usuario

Kramer

Kramer DigiTOOLS VM-2HDCP Manual de usuario

Kramer

Kramer FC-331A Manual de usuario

Kramer

Kramer DigiTOOLS 6505 Manual de usuario

Kramer

Kramer VP-558 Manual de usuario

Kramer

Kramer VP-470 Manual de usuario

Kramer

Kramer KDS-EN1 Manual de usuario

Kramer

Kramer VP-435 Manual de usuario

Kramer

Kramer VP-434 Manual de usuario

Kramer

Kramer VM-2DP Manual de usuario

Kramer

Kramer VP-503XL Manual de usuario

Kramer

Kramer FC-113 Manual de usuario

Manuales populares de Convertidor de medios de otras marcas

SoundTraxx

SoundTraxx Blunami BLU-2200 Manual de usuario

SPROLINK

SPROLINK VA1 Manual de usuario

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manual de usuario

Nikon

Nikon AF-S TC-20E III Manual de usuario

Axis

Axis AXIS Q7406 Manual de usuario

Omega

Omega TAC80B-J Manual de usuario

Zoom

Zoom Thunderbolt TAC-2R Manual de usuario

OST

OST iConverter 10/100M Manual de usuario

Vertiv

Vertiv Netsure Manual de usuario

birddog

birddog MINI Manual de usuario

Roland

Roland GI-10 Manual de usuario

Wallenstein

Wallenstein WX310 Manual de usuario

Pace

Pace MSS 200-1 Manual de usuario

Solar Converters

Solar Converters EQ 12/24-50 Manual de usuario

CYP

CYP EL-7400V Manual de usuario

TIE

TIE MIDI 1i1o Manual de usuario

DCS

DCS Vivaldi Upsampler Manual de usuario

Westermo

Westermo MCW-211 SERIES Manual de usuario