Korenix JetNet 3010G Series Manual de usuario

JetNet3010G

7 10/100TX + 3 Gigabit SFP/Gigabit Copper

Industrial Gigabit Switch

User’s Manual

Version: 2.1, Jun-2011

Korenix JetNet 3010G Series

Industrial Gigabit Ethernet Switch

User’s Manual

Reproduction in any form or by any means without permission is prohibited

1. Introduction..........................................................................................4

1-1. Features...........................................................................................4

1-2. Packing Check List..........................................................................4

2. Hardware Description..........................................................................6

2-1. Dimension........................................................................................6

2-2. Front Panel......................................................................................7

2-3. Bottom View.....................................................................................7

2-4. Wiring the Power Input.....................................................................8

2-5. wiring the Earth ground....................................................................9

2-6. LED Indicators...............................................................................10

2-7. Ethernet interface introduction.......................................................11

2-8. Quality of Service...........................................................................11

2-9. Wiring Cable..................................................................................12

3. Mounting Installation.........................................................................13

3-1. DIN Rail Mounting..........................................................................13

3-2. Wall Mounting................................................................................14

4. Hardware Installation.........................................................................16

4-1 Installation and Testing ...................................................................16

5. Trouble Shooting................................................................................20

6. Technical Specification .....................................................................20

7. SFP Fiber Transceiver Order Information........................................22

1. Introduction

In the traditional industrial communication, the communicate infrastructure is combined

with proprietary protocol and hard to connect with different layer. Today, the new trend

of industrial communication is integrated all of layers to Ethernet protocol. As the

bandwidth demands is growing up by several of applications, like video security, traffic

signal monitoring and control; this is a need of Gigabit Ethernet becomes popular in

recently.

The JetNet3010G is a 10-port Gigabit Industrial switch which embedded 7-port

10/100TX and 3 combo ports for Gigabit copper and SFP for Gigabit Ethernet uplink.

With the high bandwidth switch fabric, JetNet3010G can deliver full wire speed without

packet loss. This manual will introduce JetNet3010G hardware specification, system

installation and the applications.

1-1. Features

7 10/100TX and 3 Gigabit copper/SFP combo

IEEE802.3, 802.3u, 802.3z and 802.3ab Compliance

Auto detection Gigabit Transmission Media

Flexible Gigabit Fiber Link Distance

High performance 32Gbps Switch fabric

Supports Auto MID/MDI-X with Flow control

IEEE802.1p for Quality of Service (QoS)

Power redundancy with wide range input

1.5KV Hi-pot passed for Port, Power, Case

Rigid IP31 grade Aluminum Case

-10~60℃Hazardous Operating Temperature

1-2. Packing Check List

JetNet3010G package include the following items:

JetNet3010G x1

One DIN-Rail clip (already screwed on the back of JetNet3010G) x1

One wall mounting plate

User’s manual

Quick Installation Guide

JetNet3010G Industrial Switch User’s Manual CD-ROM Quick Installation Guide

WallMountingPlate Screwx4(M3x6mm)

Contact your sales representative if any item is missing or damaged.

2. Hardware Description

This session will introduce the enclosure interface, system power installation,

dimension and the QoS.

2-1. Dimension

The dimension of JetNet3010G is 96 mm (w) x 137 mm (H) x 119 mm (D)

2-2. Front Panel

The following diagram shows the front panel of JetNet 3010G, it describes the LEDs,

Fast Ethernet and Gigabit Ethernet ports.

Figure A. Front Panel of JetNet 3010G

2-3. Bottom View

The bottom view of the JetNet3010G Industrial Gigabit Switch consists of one

terminal block connector with two DC power inputs.

Figure B. Bottom view of the JetNet3010G Industrial Gigabit Switch

2-4. Wiring the Power Input

The JetNet 3010G supports 2 power inputs with power redundance and polarity auto

reverse functions; the typically input power voltage is DC 24V with 12~48V input range.

On the bottom side, there is one 4-pin removable terminal block for the redundant

power input and the suitable specification of power cable is 12 ~24 AWG.

Following the instructions as below to wiring the cable and switching power system.

1. Insert the positive and negative wires into the V+ and V- contacts respectively of

the terminal block connector

2. Tighten the wire-clamp screws to prevent the DC wires from being loosened.

3. The Power 1 and Power 2 support power redundancy and polarity reverse

protection functions.

4. It accepts positive or negative power system input, but Power 1 and Power 2

have to apply the same mode.

Note 1: It is a good practice to turn off input and load power, and to unplug power

terminal block before making wire connections. Otherwise, your screwdriver blade

can inadvertently short your terminal connections to the grounded enclosure.

Note 2: The range of the suitable electric wire is from 12 to 24 AWG.

Note 3: If the 2 power inputs are connected, JetNet 3010G will be powered from the

highest connected voltage. The unit will alarm for loss of power, either PWR1 or

PWR2.

Note 4: To use the UL Listed LPS Power supply with output Rating 12-48 Vdc,

minimum 1 A

2-5. wiring the Earth ground

To ensure that the system will not be damaged by noise or any electrical shock, we

suggest you make exactly connection with JetNet3010G with Earth Ground.

On the bottom side of JetNet3010G, there is one earth ground screw, loosen the earth

ground screw by screw drive and tighten the screw after earth ground wire connected

Earth Ground

2-6. LED Indicators

The front panel of JetNet3010G includes 2 Power LEDs, 6 LEDs for Gigabit SFP and

RJ-45 ports. Each 10/100Base-TX ports includes 2 LEDs with Green and Yellow color.

These LED indicators provide administrators with real-time system status. Table 1

gives descriptions of the function of each LED indicator.

LED Status Description

Green Power 1 is supplying DC power.

Power 1 Off No power is being supplied.

Green Power 2 is supplying DC power.

Power 2 Off No power is being supplied.

Green A network device is detected.

Blinks The port is transmitting or receiving

packets from the TX device.

RJ-45

(Gigabit Port 8~10)

Off No device is attached or not link

with RJ-45 port.

Green The port is transmitting or receiving

packets from the TX device.

Blinks The port is transmitting or receiving

packets from the TX device

SFP

(Gigabit Port 8~10)

Off No device is attached or not link

with RJ-45 port.

Green A network device is detected.

Blinks The port is transmitting or receiving

packets from the TX device

10/100Mbps

(Port 1 ~7)

off No device is attached or not link

with RJ-45 port.

Notes 1: It is recommended don’t connect SFP fiber transceiver and RJ-45

combo port at same time; it will cause internal wrong link signature detection

and get wrong network connection.

Notes 2: Gigabit Port 10 supports 1000Base-T (1000Mbps) or Gigabit Fiber only,

but port 8 and 9 support 10/100/1000Mbps or Gigabit Fiber

Tabla de contenidos

Otros manuales de Cambiar de Korenix

Korenix

Korenix JetNet 5210G Manual de usuario

Korenix

Korenix JetNet 5428G-20SFP Series Manual de usuario

Korenix

Korenix JetNet 5010G Series Manual de usuario

Korenix

Korenix JetNet 3018G Series Manual de usuario

Korenix

Korenix JetNet 7628X Series Manual de usuario

Korenix

Korenix JetNet 3906G Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Korenix

Korenix JetNet 3005 Manual de usuario

Korenix

Korenix JetNet 4500 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

Korenix

Korenix JetNet 6710G Manual de usuario

Korenix

Korenix JetNet 7020G Manual de usuario

Korenix

Korenix JetNet 5628G Series Manual de usuario

Korenix

Korenix JetNet 3810G Series Manual de usuario

Korenix

Korenix JetNet 3008f v3 Manual de usuario

Korenix

Korenix JetNet 3212G-2C2F Manual de usuario

Korenix

Korenix JetNet 7850G-2XG Manual de usuario

Korenix

Korenix JetNet3008G V2 Manual de usuario

Korenix

Korenix JetNet 3210GP-2C Manual de usuario

Korenix

Korenix JetNet 6710G Manual de usuario

Korenix

Korenix JetNet 3810G Series Manual de usuario

Korenix

Korenix JetNet 3705-24V Manual de usuario

Korenix

Korenix JetNet 2005f Manual de usuario

Korenix

Korenix JetCard 1204 Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario