Konica Minolta DRYPRO SIGMA Manual de usuario

KONICA MINOLTA DRYPRO SIGMA Laser Imaging System

The DRYPRO SIGMA Laser Imaging System is intended to provide hard copy images

from digital imaging source output signals onto KONICA MINOLTA MEDICAL IMAGING

FILM SD-S. The device is intended for use with a variety of digital modalities,

including, but not limited to, CR (Computed Radiology), DR (Digital Radiology), CT

(Computerized Tomography) and MRI (Magnetic Resonance Imaging). The images

are to be used for medical diagnosis and referral to physicians and their patients.

This device is not intended to be used with Full Field Digital Mammography units or

Computed Radiography units supporting digital mammography.

Intended Use

Pub No. 9G7571_en, Rev. B, 2013-04-01

KONICA MINOLTA and DRYPRO are trademarks of KONICA

MINOLTA, INC.

KONICA MINOLTA, INC.

1 Sakura-machi, Hino-shi, Tokyo, 191-8511, Japan

Getting Started

Your laser imager comes with several publications to help you get started quickly and

safely. Locate the following publications:

• SafetyManual(9G7565):Reviewthismanualrsttounderstandhowtopositionandwork

with the laser imager safely and within regulations.

• Pre-Installation Manual (9G7563): Ensure that your site is ready for the installation.

• Installation Manual (9G7567): Learn how to install the laser imager.

• Operation Manual (9G7564): See this guide for a product overview, use instructions, and

troubleshooting tips.

• Quick Reference Card (9G7566): Keep this card in a convenient place and reference it as

needed.

The DRYPRO SIGMA Laser Imager prints on KONICA MINOLTA Medical Imaging Film.

Film Types

Pub history:

A: 2011-03-31. First release.

B: Updated the company name.

2015-04-17 9G7567_en 1

Installation Manual

Requirements to install the laser imager

CAUTION:

The laser imager weighs approximately 54 kg (120 lb). Two

people must use safe lifting techniques to move the laser

imager. One person can complete the remaining steps. The

installation must be performed by qualified personnel.

Required tools • Phillips screwdriver

• Scissors

• Straight blade screwdriver

• Crossover cable (not shown)

Required information You will need:

• IP Address and related network information for the laser imager

• Configuration information for each modality that will print to the laser

imager

This information should have been previously collected and recorded in

the Pre-Installation Manual that was provided to your site.

If you do not have the Pre-Installation Manual, contact your dealer or

qualified service provider.

Task Recommended Skill or Knowledge

Unpack the laser imager. Ability to use common hand tools.

Use a personal computer to view the documentation on

the publications disc supplied with the laser imager.

Basic personal computer skills.

Connect a personal computer to the laser imager and

enter the network information.

Familiarity with TCP/IP network addressing

conventions.

Configure the laser imager to print from a modality. Familiarity with DICOM protocol.

Make a backup disk of the configuration. Understand personal computer file name

conventions.

2 9G7567_en 2015-04-17

Unpacking the laser imager

Checking the

accessories

Check that the following items are included in the accessories box:

• Power cord

• Network cable

• Deodorant filter

• Publications kit

IMPORTANT: Please read the Safety Manual before you proceed to

install or operate the laser imager.

1. Remove the two foam assemblies.

2. Open the bag that covers the laser imager.

CAUTION:

Use safe lifting techniques and two people to move the laser

imager.

3. Lift the laser imager from the carton and set it on a flat surface.

Position the laser imager temporarily so there is a space of at least

1 m (39 in.) at the back of the laser imager.

Foam Assemblies

Accessories

Box

2015-04-17 9G7567_en 3

Moving the shipping

brackets and retainer Shipping brackets are fastened inside the laser imager to keep the parts

safe during shipment. You must remove them, and then reinstall them in

a different location (as shown) inside the laser imager. This prevents the

shipping brackets from becoming lost. You must also remove the rollback

retainer.

NOTE: If it is necessary to ship the laser imager again, you must return

the shipping brackets to the shipping locations.

1. To move the back shipping brackets, remove:

a. Back cover

b. 4 screws that fasten the 2 shipping brackets

Back view of laser imager

2. Rotate the shipping brackets and reattach them in the alternate set

of holes on the rail.

3. Retain the other 2 bracket screws: Install the screws into any of the

empty holes where the bracket was attached earlier.

4. Replace the back cover.

5. At the front of the imager, open the film supply. Reach in and

remove the foam rollback retainer.

Shipping Brackets

Shipping Brackets reattached

4 9G7567_en 2015-04-17

6. To move the front shipping bracket, remove 4 screws that fasten the

shipping bracket.

Front view of laser imager

7. Use 2 of the screws to reattach the shipping bracket in the alternate

set of holes on the left side of the rail.

8. Retain the other 2 bracket screws: Install the screws into any of the

empty holes where the bracket was attached earlier.

9. Remove the right cover:

a. Remove the top cover. (Leave the film supply open.)

b. Remove 2 screws that attach to the right cover standoffs.

FRONT SHIPPING

BRACKET

(FILTER REMOVED

Shipping

Bracket

Front Shipping

Bracket in

Storage

Shipping

Bracket

reattached

H221_6003AC

2 screws

2015-04-17 9G7567_en 5

10. Behind the right cover, locate the tie wrap that fastens the exposure

transport belt. The tie wrap removes tension from the belt during

shipping. Cut and remove the tie wrap from the belt.

11. Install the deodorant filter.

12. Reinstall the right and top covers.

13. Close the film supply.

H221_6030GC

Tie Wrap

Film Supply

Filter

6 9G7567_en 2015-04-17

Connecting to electrical power

1. Locate the power cord. The power cord must match the AC power

outlets at your site.

If you cannot use the power cord that is provided, obtain a suitable

power cord locally. You must use an agency-approved power cord

rated for adequate amperage with a plug type suitable for your

location. Contact your dealer if you need assistance.

2. Check that the voltage on the label over the power cord inlet

matches the AC voltage at your site.

CAUTION:

If the voltage on the label does not match the AC voltage at

your site, do not continue with the installation. Contact your

dealer or qualified service provider.

Power cord inlet labels and connectors

3. Remove the power cord inlet label.

RISK OF ELECTRIC SHOCK:

Dangerous voltage!

4. Connect the power cord to the:

• AC power connector on the laser imager.

• Building AC power outlet.

Laser

Imager

Back

Panel

2015-04-17 9G7567_en 7

Applying power

1. Check that the film supply is closed.

2. To start the laser imager, press the power switch on the back of the

laser imager to on (|). Wait as the laser imager warms up. The

warm-up period might last up to 30 minutes. The display screen

shows the progress as the laser imager becomes ready to print.

Warming up

The warm-up period varies depending on how long the laser imager

has been off and the ambient temperature.

NOTE: If the laser imager does not start, see “Troubleshooting” on page

12.

Inserting a film cartridge

1. Open the film supply.

2. Insert the film cartridge. Align the cartridge with the label facing up

and the perforations to the front. Set the leading edge on the

cartridge guides, then slide the film cartridge into the laser imager to

engage the detents in the bottom of the cartridge.

3. Close the film supply.

4. Check that the film count appears on the display screen.

NOTE: If a film count does not appear, see the Operation Manual for

help.

The power symbol is

yellow and flashing

while the laser

imager warms up

A countdown to zero (0) indicates

how soon the laser imager will be

ready to print

H210_1020AC

H210_1020ACA

Leading Edge

Detents

Perforations

Cartridge

Guide

Film Supply

8 9G7567_en 2015-04-17

Configuring the laser imager

Setting up your

computer to

communicate with the

laser imager

Do this procedure at your computer.

1. Select Start>Settings>Network Connections.

NOTE: Depending on your operating system, this might be

Start>Settings>Network and Dial-up Connections.

2. Right-click Local Area Connection.

3. Select Properties.

4. Select Internet Protocol (TCP/IP).

5. Click Properties.

IMPORTANT: Remember or write down your current settings, as you

will reset your computer to these settings near the end of

the installation.

6. Select the option button next to Obtain an IP address

automatically.

7. Click OK.

8. Click OK.

Connecting your

computer to the laser

imager

1. Remove the laser imager’s top cover.

2. Using a crossover cable, connect your computer to the service port

on the laser imager.

3. Route the crossover cable so that it does not interfere with the top

cover when it is installed.

4. Reinstall the top cover.

H221_6031HC

Service

Port

Top Cover

Crossover Cable

2015-04-17 9G7567_en 9

Configuring

site-specific information

1. Start MICROSOFT INTERNET EXPLORER.

2. In the Address box, type: 192.168.0.1

3. Click Go. The main screen for the Web Portal appears.

4. If you are using INTERNET EXPLORER 8, set the IE8 window to

compatibility view. Click the Compatibility View toolbar button. This

will correct some potential viewing issues with IE8. If the icon is not

on the toolbar, select Compatibility View from the Tools menu.

5. Select your language:

6. Select Wizards > Installation Assistant.

7. Click at the bottom of the screen. The Network Configuration

screen appears.

8. Enter:

•HostName

• IP Address

• Subnet Mask

• Default Gateway

Otros manuales para DRYPRO SIGMA

Tabla de contenidos

Otros manuales de Impresora de Konica Minolta

Konica Minolta

Konica Minolta BIZHUB C250 Manual de usuario

Konica Minolta

Konica Minolta BIZHUB C250P Manual de usuario

Konica Minolta

Konica Minolta Magicolor 2530 DL Manual de usuario

Konica Minolta

Konica Minolta bizhub PRESS C70hc Manual de usuario

Konica Minolta

Konica Minolta magicolor 7450 Manual de usuario

Konica Minolta

Konica Minolta Magicolor 4750DN Manual de usuario

Konica Minolta

Konica Minolta bizhub 40P/40PX Instrucciones originales

Konica Minolta

Konica Minolta BIZHUB PRO C5500 Manual

Konica Minolta

Konica Minolta bizhub C31P Manual de usuario

Konica Minolta

Konica Minolta Magicolor 4750DN Manual de usuario

Konica Minolta

Konica Minolta Magicolor 2450 Manual de usuario

Konica Minolta

Konica Minolta bizhub 20 Manual de usuario

Konica Minolta

Konica Minolta magicolor 1650EN Manual de usuario

Konica Minolta

Konica Minolta bizhub C31P Manual de usuario

Konica Minolta

Konica Minolta magicolor 2430 DL Manual de usuario

Konica Minolta

Konica Minolta PagePro 1380 MF Manual de usuario

Konica Minolta

Konica Minolta PagePro 1350W Guía de inicio rápido

Konica Minolta

Konica Minolta bizhub 3301P Manual de usuario

Konica Minolta

Konica Minolta BIZHUB 500 Manual de usuario

Konica Minolta

Konica Minolta KIP 7700 Manual de usuario

Konica Minolta

Konica Minolta Magicolor 5450 Manual de usuario

Konica Minolta

Konica Minolta bizhub PRESS 1250/1250P Manual de usuario

Konica Minolta

Konica Minolta magicolor 1690MF Manual de usuario

Konica Minolta

Konica Minolta magicolor 1650EN Instrucciones originales

Manuales populares de Impresora de otras marcas

Lexmark

Lexmark 1400 Series Manual

Canon

Canon i70 Series Manual de usuario

Evolis

Evolis Elypso Manual de usuario

Kyocera

Kyocera FS-9530DN Manual de usuario

Canon

Canon LASER SHOT LBP-1210 Manual de usuario

Samsung

Samsung BIXOLON SRP-350plusF Manual de usuario

Canon

Canon PIXMA PRO-1 Series Manual de usuario

Canon

Canon PIXMA G3560 Guía de configuración

Dell

Dell Color Laser Printer 2130cn Manual de usuario

Tektronix

Tektronix Phaser 840 Manual de usuario

Epson

Epson ET-7750 Instrucciones de funcionamiento

Canon

Canon CLBR 460ps Manual de usuario

Eltron

Eltron P210 Guide Manual de usuario

Ricoh

Ricoh MD-P1 Manual de usuario

Epson

Epson SC-F7100 series Manual de usuario

Epson

Epson Stylus C40UX Manual de usuario

Canon

Canon imagePASS-A2 Manual de usuario

Canon

Canon S820D Manual de usuario