Konica Minolta Bizhub C652 Series Manual de usuario

E-1

INSTALLATION MANUAL

A0P0-9951-01

Be sure to correctly follow the procedures in order as explained in this Installation Manual.

If you do not follow the procedure in order, the image trouble may occur.

I. Outline of installation procedures

When installing the machine and associated options as a system, follow the order shown on the upper.

Note:

• For the detailed installation procedures for each option, follow the instructions given in the corresponding

installation manual and perform the procedures correctly.

• Once the Power Switch is turned ON, do not turn OFF it until the installation work has been completed.

• When transporting the machine, assign an adequate number of persons to the job and follow the speci-

fied correct procedures.

(mass: approx. 221 kg (487-1/4 lb))

OT-503

Machine

Electron system options

MK-715*1

SP-501

IC-412*2

VI-505*2

✱Electron system options

MK-720*2

EK-604*2

UK-203*2

WT-506

AU-102 LU-204

*1 : Varies depending on the applicable marketing area.

*2 : No particular order in installation procedures.

AU-101

FS-526

AU-201 LU-301

PK-516

SD-508 FK-502

KH-101

A0P0IXC010DA

Applied Machine: /

E-2

II. Installation space (unit: mm (inch))

bizhub C652 + FS-526 + LU-204

III. Pre-installation check items

1. Select a level and stable place for installing the

machine.

2. Be sure to use a power source of the voltage and

frequency indicated in the product specifications.

Ensure that the current carrying capacity of the

power outlet is at least equal to the current listed

in the product specifications.

3. Power the machine directly from a dedicated

power outlet. (Do not use an extension cord.)

4. Do not plug or unplug the power cord with wet or

dirty hands, otherwise you may get an electric

shock.

5. Avoid a hot and humid environment, or a place

exposed to direct sunlight.

6. Avoid a dusty location, or a place near volatile

and flammable substances.

7. Avoid a poorly ventilated place.

IV. Accessory parts

* Varies depending on the applicable marketing

area.

Note:

Keep the label (Super G3 label) at hand. It is nec-

essary for mounting the FAX Kit.

A0P0IXC011DA

418

(16-7/16)

1107

(43-9/16)

1155

(45-1/2)

495

(19-1/2)

886

(34-7/8)

1252

(49-5/16)

1575 (62-1/16)

1650 (64-15/16)

2376 (93-9/16)

238

(9-3/8)

(2)

No. Name Q’ty

1. Imaging unit (IU): Y,M,C 3

2. Developing unit: K 1

3. Drum unit: K 1

4. User’s guide holder 1

5. Quick guide

(Copy/Fax/Scan/Box operations) * 1

6. Installation manual 1 set

7. User’s guide CD * 1

8. CD-ROM * 1 set

9. Tray label 1

10. Paper size label 1

11. Label (Legal restrictions on copying) * 1

12. Label (Super G3 label) 1

13. Chart 1

14. Cap A (black) 2

15. Cap B (white) 2

16. Power cord * 1

17. Connector cover 1

18. IR Cover 1

19. Mounting screw 1

20. Spacer A 1

21. Spacer B 1

22. Power cord instruction * 1

23. Panel pen 1

After unpacking, be sure to get rid of the

packaging materials and keep them out of

the reach of children.

Putting the head in the plastic bag

involves danger of suffocation.

E-3

V. Unpacking the machine

1. Open the shipping box and take out the IU ship-

ping box and packaging material.

Note:

• Save the slope and cushion removed here for

later use.

• When storing or moving the IU, be sure to face

the TOP side up.

2. Remove the fixing material (upper).

3. Hold onto the handle of the machine and tilt the

machine to the right and left. Under this condition,

remove the mirror mat and fixing material (lower).

4. Separate the cushion into two and install them to

the pallet (at two places).

5. Take out the slope and protective tape and

remove nails from the plastic bag.

A0P0IXC014DA

Cushion

Slope

A0P0IXC015DA

A0P0IXC016DB

A0P0IXC017DB

A0P0IXC018DB

A0P0IXC019DA

A0P0IXC067DA

E-4

6. Position the slope as illustrated and drive nails in

to fix the slope in position.

Note:

Insert the nails in the outer holes.

7. Holding onto the front cover and the back panel

of the machine, slide the machine down along the

slope.

Note:

Machine mass: 207 kg (456-1/4 lb)

• Perform this step on a level, stable site and

assign an adequate number of persons.

• When sliding the machine down, do not hold

onto the IR portion.

• Do not insert your leg under the slope.

VI. Removing protective tape, packing and

other shipping materials

1. Remove the protective tape and protective mate-

rial.

Note:

After removing protective tape B, be sure to lock

the lever.

A0P0IXC020DA

A0P0IXC021DA

A0P0IXE069DC

A0P0IXC068DA

A0P0IXE070DB

A0P0IXC044DB

E-5

2. Remove the protective material.

3. Remove the reinforcement plate (four screws).

4. Remove the packing bracket.

Note:

Do not loosen or remove the shoulder screw from

the portion on which the packing bracket A is

mounted.

5. Pull the tray 1 out and remove the protective tape

from the tray.

6. Pull the tray 2 out and remove the protective tape

from the tray.

7. Pull trays 3 and 4 out and remove the desiccant

and protective sheet.

A0P0IXC045DA

A0P0IXC046DA

A0P0IXC047DA

Packing

bracket A

A0P0IXC048DA

A0P0IXC049DA

A0P0IXC022DB

E-6

8. Remove the protective tape from trays 3 and 4.

VII. Installing the IU

1. Open the lower front door.

2. Remove the waste toner box fixing lever and the

waste toner box.

3. Tilt the IU to the right and, in that condition, shake

it over a small stroke twice. Then, tilt the IU to the

left and, in that condition, shake it over a small

stroke twice.

Note:

• Perform this step only for the color IU (Y, M,

and C).

• Shake the IU adequately. Otherwise, it may

cause trouble.

4. Remove protective tape of the IU.

5. Remove the protective sheet.

A0P0IXC023DB

A0P0IXC007DA

A0P0IXC008DA

A00JIXC028DB

A00JIXC228DA

A00JIXC030DC

Protective sheet

E-7

6. Unlock the IU fixing lever.

7. Keeping the IU in the level position, insert it all

the way as far as it will go.

Note:

Make sure that the color is same between insert-

ing port and the IU.

8. Push the IU all the way in.

Note:

Make sure that the IU is pushed all the way in.

9. Fix the IU in position using the IU fixing lever.

10. Using the same procedure, install all IUs.

11. Remove the tape and the mounting bracket from

the position shown below of the developing unit.

12. Remove two springs and a shutter, which are

used in step 15, from the bag.

A0P0IXC024DA

A0P0IXC025DA

A0P0IXC026DA

A0P0IXC027DA

A0P0IXC028DB

A0P0IXC079DA

E-8

13. Hold the developing unit upside down and

remove the cap.

14. Remove the protective tape.

Note:

Be careful that developer does not spill from the

hole on the developing unit.

15. Attach the two springs and the shutter removed

in step 12 to the developing unit.

16. Remove the protective material.

17. Slide out the rail from the machine.

18. Remove one shoulder screw.

A0P0IXC081DA

A0P0IXC082DA

A0P0IXC083DA

A0P0IXC034DB

A0P0IXC035DA

A0P0IXC036DB

E-9

19. While aligning part A of the developing unit with

the screw hole on the rail, pass part B of the

developing unit under the rail.

20. Align part A of the developing unit with part B of

the rail and place the developing unit on the rail

of the machine.

Note:

Make sure that the positioning metal bracket of the

rail fits in the cutout in the developing unit.

21. Fix the developing unit to the rail using the

shoulder screw removed in step 18.

22. Remove the caps from the front and rear ends of

the drum unit.

A0P0IXC080DA

Part A

Part B

A0P0IXC037DB

Part A

Part B

Cutout

Positioning

metal bracket

A0P0IXC038DB

A0P0IXC039DA

E-10

23. Put the drum unit on the developing unit.

Note:

• Do not tilt the drum unit when putting it on the

developing unit. (Keep the drum unit level.)

• Position the drum unit so that part A of the drum

unit is inserted into part B of the developing

unit.

• Position the drum unit so that part C of the

drum unit is inside the mylar located on the

main body rail. (Check that Part C is not on the

top of the rail.)

24. Peel off the protective sheet of the drum unit.

25. Secure the drum unit to the developing unit with

the two levers.

Note:

• Push the front and back levers in the direction

of the arrow at a time to secure the drum unit.

• Check that the front lever of the drum unit is

parallel to the vertical line marked on the label

on the developing unit.

A0P0IXC071DA

Part A

Part B

A0P0IXC085DA

Mylar

OK NG

Part C

A0P0IXC041DB

A0P0IXC040DC

Front lever

Parallel

Label (Vertical line)

Otros manuales para bizhub C652 Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Impresora de Konica Minolta

Konica Minolta

Konica Minolta magicolor 7450 Guía de inicio rápido

Konica Minolta

Konica Minolta bizhub 224e Manual de usuario

Konica Minolta

Konica Minolta MAGICOLOR 7450II GA Manual de usuario

Konica Minolta

Konica Minolta bizhub 163 Manual de usuario

Konica Minolta

Konica Minolta magicolor 7450 Manual de usuario

Konica Minolta

Konica Minolta magicolor 1650EN Instrucciones originales

Konica Minolta

Konica Minolta AccurioPress C3080 Manual de usuario

Konica Minolta

Konica Minolta PAGEPRO 5650EN Manual de usuario

Konica Minolta

Konica Minolta 1800767-001A Manual de usuario

Konica Minolta

Konica Minolta BIZHUB C30P Manual de usuario

Konica Minolta

Konica Minolta bizhub C31P Manual de usuario

Konica Minolta

Konica Minolta magicolor 7450 II Manual de usuario

Konica Minolta

Konica Minolta AccurioPress 6136 Manual de usuario

Konica Minolta

Konica Minolta bizhub 4422 Manual de usuario

Konica Minolta

Konica Minolta Magicolor 7300 Manual de usuario

Konica Minolta

Konica Minolta Magicolor 2500W Manual

Konica Minolta

Konica Minolta magicolor 4750EN/4750DN Manual de usuario

Konica Minolta

Konica Minolta AccurioPress C2070 Manual de usuario

Konica Minolta

Konica Minolta magicolor 2430 DL Manual de usuario

Konica Minolta

Konica Minolta bizhub PRO 1200 Series Manual

Konica Minolta

Konica Minolta AccurioPress C3080 Manual de usuario

Konica Minolta

Konica Minolta magicolor 1600W Manual de usuario

Konica Minolta

Konica Minolta bizhub C550 Series Manual de usuario

Konica Minolta

Konica Minolta BIZHUB C30P Manual de usuario

Manuales populares de Impresora de otras marcas

Lexmark

Lexmark 1400 Series Manual

Canon

Canon i70 Series Manual de usuario

Evolis

Evolis Elypso Manual de usuario

Kyocera

Kyocera FS-9530DN Manual de usuario

Canon

Canon LASER SHOT LBP-1210 Manual de usuario

Samsung

Samsung BIXOLON SRP-350plusF Manual de usuario

Canon

Canon PIXMA PRO-1 Series Manual de usuario

Canon

Canon PIXMA G3560 Guía de configuración

Dell

Dell Color Laser Printer 2130cn Manual de usuario

Tektronix

Tektronix Phaser 840 Manual de usuario

Epson

Epson ET-7750 Instrucciones de funcionamiento

Canon

Canon CLBR 460ps Manual de usuario

Eltron

Eltron P210 Guide Manual de usuario

Ricoh

Ricoh MD-P1 Manual de usuario

Epson

Epson SC-F7100 series Manual de usuario

Epson

Epson Stylus C40UX Manual de usuario

Canon

Canon imagePASS-A2 Manual de usuario

Canon

Canon S820D Manual de usuario

Konica Minolta bizhub C652 Series Manual de usuario

Manuales populares de Impresora de otras marcas