Konica Minolta DiMAGE Z3 Manual de usuario

www.konicaminolta.com

www.konicaminoltasupport.com

DiMAGE Z3 Camera Firmware Ver.1.03e

This section explains how to install DiMAGE Z3 firmware version 1.03e. (Firmware is software used

internally to control the camera.) Be sure to read through the following explanation before you

install the software. Do not turn the camera OFF during installation; doing so could damage the

CPU inside the camera.

Contents of update

To support 2GB SD memory card.

Target products

This firmware is for use only with the DiMAGE Z3 and cannot be used with other products.

If the firmware version is already Ver.1.03e, it is not necessary to update the firmware. (Check the

firmware version as shown below.)

Checking the camera firmware version

1. Press the main switch to turn ON the camera.

2. Press the menu button.

3. Press the right key of the controller, select SETUP icon,

and press the center of the controller to display the

setup menu.

4. Confirm that the section 1 menu tab is highlighted, and

press the macro mode button. A window will open to

indicate the firmware version.

5. Check the version number of displayed on the LCD mon-

itor. If the version is Ver.1.02e or earlier, the camera must

be updated.

Press the central button of controller to close the version

number display.

KONICA MINOLTA SOFTWARE INSTALL GUIDE

1. Two respective download files have been prepared for Windows & Macintosh. Please use the

suitable one for your PC. Please read the end-user license agreement in advance of saving the

file on your PC.

The downloaded file is compressed.

-Windows- z3v103e.exe--808KB

Double-click the downloaded file.

The file is a self-extracting archive, and decompresses automatically.

-Macintosh- z3v103e.sea.hqx--1.1MB

Use Stuffit Expander or another such software utility to extract the downloaded file.

*After creating a folder in your PC and extracting the contents of the archive, the following folder is

created.

"z3v103" folder "z3v103" folder includes bellow files.

"dsc.app" file (Windows 2.07MB / Macintosh 2.1MB)

"ram.bin" file (Windows 92.9KB / Macintosh 96KB)

* Copy the "dsc.app" file and "ram.bin"

file onto the SD memory card.

For Windows For Macintosh

When copying via CompactFlash card reader When copying via DiMAGE Z3 connected to

PC using USB-cable USB-2

Preparing the SD memory card for updating

A downloaded file must be copied to a SD memory card in the camera. Before updating the cam-

era, read the data-transfer section of the DiMAGE Z3 instruction manual to connect the camera to

a computer.

• Prepare a 8MB or larger SD memory card and insert it in the camera.

• Make sure that the SD memory card has been formatted by the camera.

• Using the USB cable, connect the camera to a computer. If the camera is not compatible

with the computer system, a SD memory card reader can be used instead.

• Confirm the option “Transfer mode” in section 1 of the setup menu is set to “Data storage”,

the default setting.

2.Confirm that the file has been copied to the card using the computer.

3.Disconnect the camera from the computer or remove the SD memory card from the

card reader.

If you are using Windows Me, 2000 or XP, click the unplug-or-eject-hardware icon

in the lower right-hand corner of the screen, wait until the safe-to remove-hardware

window appears, then remove the SD memory card the card reader, or disconnect

the USB cable from the camera.

How to update firmware

NOTE:

When performing the software update, use new Alkaline batteries, fully recharged Ni-MH batteries

or the AC adapter AC-1L or AC-11 (sold separately).

When using the AC adapter, be sure not to inadvertently disconnect the camera during the soft-

ware updating procedure, otherwise the camera may be permanently damaged.

* After updating the firmware, it is necessary to operate the reset default function, and camera

settings will be reset to the default settings.

1. With the camera off, insert the prepared SD Memory

card.

2. Press and hold the shutter-release button all the way

down without turning on the camera.

3. Without lifting the your finger from the shutter-release

button, press the main switch to turn on the camera.

4. The access lamp will be lit. Please wait until the lamp

turn off. (It takes 1 or 2 minutes. You can release your

fingers from the shutter-release button and the main

switch.)

5. When the access lamp turns off, updating is completed.

Remove the batteries and then insert them again.

(When using AC adapter, disconnect the AC adapter

and then connect it again.)

6. Check that the camera firmware version number has

changed to "Ver.1.03e". (See the "Checking the camera

software version")

* If the updating failed or an error occurred during the

procedure, turn the camera off, and repeat the proce-

dure from step 1.

After checking the version number, press the center

button of controller. Setup menu will be displayed.

* After updating the camera, delete both "dsc.app" and "ram.bin" files from the SD memory card.

* Windows and Windows Me, 2000 and XP are registered trademarks of Microsoft Corporation in the U.S.A and other countries.

* Macintosh is a registered trademark of Apple Computer Inc. in the U.S.A. and other countries.

For questions or comments about this matter, contact your nearest Konicaminolta service facility.

07.2005/12984

Otros manuales para DiMAGE Z3

Tabla de contenidos

Otros manuales de Cámara digital de Konica Minolta

Konica Minolta

Konica Minolta Digital Revio KD-300Z Manual de usuario

Konica Minolta

Konica Minolta Minolta DiMAGE Xt Biz Manual de usuario

Konica Minolta

Konica Minolta Dynax DYNAX 5D Manual

Konica Minolta

Konica Minolta DIMAGE A2 - SOFTWARE Manual de usuario

Konica Minolta

Konica Minolta DiMAGE G530 Manual de usuario

Konica Minolta

Konica Minolta DiMAGE Z10 Manual de usuario

Konica Minolta

Konica Minolta DiMAGE Z20 Manual de usuario

Konica Minolta

Konica Minolta Q-Mini Manual de usuario

Konica Minolta

Konica Minolta e-mini Manual de usuario

Konica Minolta

Konica Minolta Digital Revio KD-210Z Manual de usuario

Konica Minolta

Konica Minolta Digital Still Camera KD-30M Manual de usuario

Konica Minolta

Konica Minolta DiMAGE G600 Manual de usuario

Konica Minolta

Konica Minolta MAXXUM 5D Manual de usuario

Konica Minolta

Konica Minolta DiMAGE X21 Manual de usuario

Konica Minolta

Konica Minolta E-Mini-M E-Mini-Multi-Media Camera Manual de usuario

Konica Minolta

Konica Minolta Digital Still Camera Revio KD-3300 Manual de usuario

Konica Minolta

Konica Minolta DiMAGE Z6 Manual de usuario

Konica Minolta

Konica Minolta DiMAGE E50 Manual de usuario

Konica Minolta

Konica Minolta MAXXUM 5D Manual de usuario

Konica Minolta

Konica Minolta DiMAGE E40 Manual de usuario

Konica Minolta

Konica Minolta Q-M100 Manual de usuario

Konica Minolta

Konica Minolta KD-310Z Manual de usuario

Konica Minolta

Konica Minolta DYNAX 60 - PART 2 Manual de usuario

Konica Minolta

Konica Minolta Digital Camera Manual de usuario

Manuales populares de Cámara digital de otras marcas

Mercury

Mercury 350K Manual de usuario

Pentax

Pentax Optio LS 465 Manual de usuario

Sanyo

Sanyo VPC-S1085 Manual de usuario

GE SMART A1255 Manual de usuario

Point Grey

Point Grey Gazelle Manual de usuario

Nikon

Nikon COOLPIX A Manual de usuario

Pentax

Pentax P-5 Manual de usuario

BlazeVideo

BlazeVideo A280 Manual de usuario

Sony

Sony MCA-20 Manual de usuario

Sony

Sony Alpha DSLR-A290 Manual de usuario

ATIK Cameras

ATIK Cameras One Manual de usuario

CohuHD Costar

CohuHD Costar 3930 Series Manual de usuario

Leica

Leica M10-R Manual de usuario

FujiFilm

FujiFilm FinePix A700 Manual de usuario

Lorex

Lorex LNZ81P25 Series Manual de usuario

GE J1470S Manual de usuario

Sony

Sony A6700 Guía del usuario

Canon

Canon EOS ELAN7 Manual de usuario