Konica Minolta DiMAGE X1 Instrucciones de montaje

DiMAGE X1 Camera Firmware Ver.1.10

This section explains how to install DiMAGE X1 firmware version 1.10. (Firmware is soft-

ware used internally to control the camera.) Be sure to read through the following explana-

tion before you install the firmware. Do not turn the camera OFF during installation; doing

so could damage the CPU inside the camera.

Contents of update

1. Shortened shutter-release time lag.

(Time period from when the shutter-release button is pressed down fully to when exposure

begins.)

2. Shortened operation time lag.

(Time period from zooming lever is operated to when operation of any other function button

is accepted.)

Target products

This firmware is for use only with the DiMAGE X1 and cannot be used with other products.

If the firmware version is already Ver.1.10, it is not necessary to update the firmware.

(Check the firmware version as shown below.)

www.konicaminolta.com

www.konicaminoltasupport.com

X1_FW_upd110_GB_r4.qxd 29.09.2005 16:26 Uhr Seite 1

1. Press the main switch (a) to turn on the camera.

2. Press the menu button (b) to open the recording

menu.

3. Press the left/right keys of the controller (c) to high-

light the setup menu icon, and press the center but-

ton to enter.

4. Press the left/right keys of the controller (c) to high-

light the set up tab 4, and press the up/down keys

to highlight “Firmware ver,” option.

Highlight “Enter” option and press the center button

of the controller to enter.

A window will open to indicate the firmware version.

Checking the camera firmware version

X1_FW_upd110_GB_r4.qxd 29.09.2005 16:26 Uhr Seite 2

A downloaded file must be copied to a Secure Digital (SD) memory card by either methods as

shown below.

Prepare an 8MB or larger SD memory card and insert it in the camera.

• Make sure that the SD memory card has been formatted by the camera.

5. Check the displayed version number. If it is Ver.

1.10, the camera need not be updated.

Press the center button of the controller to close

the window.

Checking the camera firmware version

Copying via SD memory card reader

• Please refer to the instruction manual for

the card reader for details.

Copying via DiMAGE X1 (loaded on the Cradle CA-

1) connected to PC

• Confirm data storage is selected in the transfer-

mode option in section 4 of the setup menu.

• Refer to the data-transfer section of the

DiMAGE X1 instruction manual to connect the

camera to a computer.

Preparing the SD memory card for updating

X1_FW_upd110_GB_r4.qxd 29.09.2005 16:26 Uhr Seite 3

1. Download the firmware file suitable for your PC after carefully reading the end-user license

agreement, and save the file in your PC.

The downloaded file is compressed.

-Windows-

x1v110.exe--636KB

Double-click the downloaded file.

The file is a self-extracting archive, and decompresses automatically.

-Macintosh-

x1v110.sit.hqx--832KB

Use Stuffit Expander or another such software utility to extract the downloaded file.

[Decompressing the downloaded file with Mac OS X v10.4]

The StuffIt Expander does not come with Mac OS X v10.4. For details, please visit:

http://docs.info.apple.com/article.html?artnum=301016

If no decompressing application is included in the computer, please install separately.

After creating a folder in your PC and extracting the contents of the archive, the “FIRMWARE” folder

containing the following file is created.

FIRMWARE.BIN: Windows 2.37MB / Macintosh 2.3MB

Copy the "FIRMWARE" folder onto root directory of the SD memory card.

For Macintosh

For Windows

Preparing the SD memory card for updating

X1_FW_upd110_GB_r4.qxd 29.09.2005 16:26 Uhr Seite 4

2. Open the FIRMWARE folder of the SD memory card to confirm that the FIRMWARE.BIN file has

been successfully copied.

3. Disconnect the camera from the computer or remove the SD memory card from the card reader.

- If you are using Windows Me, 2000 or XP, click the unplug-or-eject-hard-

ware icon in the lower right-hand corner of the screen, wait until the safe-to

remove-hardware window appears, then remove the SD memory card from

the card reader, or disconnect the camera from PC.

- When the camera is connected to PC via the cradle, turn the camera off in advance of remov-

ing it from the cradle.

Preparing the SD memory card for updating

X1_FW_upd110_GB_r4.qxd 29.09.2005 16:26 Uhr Seite 5

Note: When performing the firmware update, use fully charged Lithium-ion Battery NP-1 or

the AC Adapter Set (sold separately). When using the AC Adapter Set, be sure not to

inadvertently disconnect the camera during the firmware updating procedure, other-

wise the camera may be permanently damaged.

- Do not use the cradle during the firmware updating procedure in the camera.

How to update firmware

1. Confirm that the camera is turned off.

Insert the prepared SD memory card.

2. Press and hold the Mode button (d) for approx. 2

seconds.

The camera turns on automatically. (Do not turn the

camera on by pressing the main switch.)

3. When the confirmation screen appears, highlight

“Yes” and press the center button of the controller

to start the update.

4. Update program runs for approx. 1 minute.

X1_FW_upd110_GB_r4.qxd 29.09.2005 16:26 Uhr Seite 6

How to update firmware

5. The updating-completed message appears.

Turn the camera off.

6. Turn the camera on by pressing the main switch, to

confirm the firmware version.

7. Check that the camera firmware version number

has changed to “Ver.1.10”. (See the “Checking the

camera firmware version”)

• If the original firmware version number remains dis-

played or an error occurs during updating proce-

dure, turn the camera off and repeat (1) to (7).

8. Press the center button of the controller to close

the window.

After updating, perform ‘Reset default’ as follows:

9. Press the left/right keys of the controller to highlight

the set up tab 3, and press the up/down keys of the

controller to highlight “Reset default” option.

Highlight “Enter” option and press the center button

of the controller to enter.

X1_FW_upd110_GB_r4.qxd 29.09.2005 16:26 Uhr Seite 7

10. When the confirmation screen appears, highlight

“Yes” and press the center button of the controller.

• In advance of using the prepared SD memory card

for recording image, format it via the camera or

delete the file/folder prepared for firmware update.

* Windows and Windows Me, 2000 and XP are registered trademarks of Microsoft Corporation in

the U.S.A and other countries.

* Macintosh is a registered trademark of Apple Computer Inc. in the U.S.A. and other countries.

For questions or comments about this matter, contact your nearest Konicaminolta service facility.

How to update firmware

X1_FW_upd110_GB_r4.qxd 29.09.2005 16:26 Uhr Seite 8

Otros manuales para DiMAGE X1

Tabla de contenidos

Otros manuales de Cámara digital de Konica Minolta

Konica Minolta

Konica Minolta Digital Revio KD-210Z Manual de usuario

Konica Minolta

Konica Minolta KD-310Z Manual de usuario

Konica Minolta

Konica Minolta Revio KD-220z Manual de usuario

Konica Minolta

Konica Minolta Revio KD-220z Manual de usuario

Konica Minolta

Konica Minolta DiMAGE Z1 Manual de usuario

Konica Minolta

Konica Minolta DIMAGE X1 9979-2801-80/12984 Manual

Konica Minolta

Konica Minolta DiMAGE G400 Manual de usuario

Konica Minolta

Konica Minolta Revio C2 Manual de usuario

Konica Minolta

Konica Minolta Q-mini K-QM-3501E Manual de usuario

Konica Minolta

Konica Minolta Digital Revio KD-300Z Manual de usuario

Konica Minolta

Konica Minolta DiMAGE Z3 Manual de usuario

Konica Minolta

Konica Minolta DiMAGE Z1 Manual de usuario

Konica Minolta

Konica Minolta S3 Manual de usuario

Konica Minolta

Konica Minolta DiMAGE Z6 Manual de usuario

Konica Minolta

Konica Minolta DiMAGE Z20 Manual de usuario

Konica Minolta

Konica Minolta DiMAGE X31 Manual de usuario

Konica Minolta

Konica Minolta Minolta DiMAGE Xt Biz Manual de usuario

Konica Minolta

Konica Minolta DiMAGE X31 Manual de usuario

Konica Minolta

Konica Minolta DiMAGE Xg Manual de usuario

Konica Minolta

Konica Minolta DiMAGE Z10 Manual de usuario

Konica Minolta

Konica Minolta DiMAGE X50 Manual de usuario

Konica Minolta

Konica Minolta AUTOREFLEX T4 Manual de usuario

Konica Minolta

Konica Minolta DYNAX DYNAX7D Manual de usuario

Konica Minolta

Konica Minolta DiMAGE E40 Manual de usuario

Manuales populares de Cámara digital de otras marcas

Mercury

Mercury 350K Manual de usuario

Pentax

Pentax Optio LS 465 Manual de usuario

Sanyo

Sanyo VPC-S1085 Manual de usuario

GE SMART A1255 Manual de usuario

Point Grey

Point Grey Gazelle Manual de usuario

Nikon

Nikon COOLPIX A Manual de usuario

Pentax

Pentax P-5 Manual de usuario

BlazeVideo

BlazeVideo A280 Manual de usuario

Sony

Sony MCA-20 Manual de usuario

Sony

Sony Alpha DSLR-A290 Manual de usuario

ATIK Cameras

ATIK Cameras One Manual de usuario

CohuHD Costar

CohuHD Costar 3930 Series Manual de usuario

Leica

Leica M10-R Manual de usuario

FujiFilm

FujiFilm FinePix A700 Manual de usuario

Lorex

Lorex LNZ81P25 Series Manual de usuario

GE J1470S Manual de usuario

Sony

Sony A6700 Guía del usuario

Canon

Canon EOS ELAN7 Manual de usuario