Kohler K-378 Manual de usuario
Installation Guide
Kitchen Sink Faucet
Mproduct numbers are for Mexico (i.e. K-12345M)
Los números de productos seguidos de
Mcorresponden a México (Ej.
K-12345M)
Français, page ″Français-1″
Español, página ″Español-1″
K-377, K-378 K-16109, K-16111
1004636-2-E
Tools and Materials
Thank You For Choosing Kohler Company
We appreciate your commitment to Kohler quality. Please take a few
minutes to review this manual before you start installation. If you
encounter any installation or performance problems, please don’t
hesitate to contact us. Our phone numbers and website are listed on
the back cover. Thanks again for choosing Kohler Company.
Before You Begin
Observe all local plumbing and building codes.
Shut off the water supplies.
Before installation, unpack the new faucet and inspect it for
damage. Return the faucet to the carton until you are ready to
install it.
Carefully inspect waste and supply tubing for any sign of
damage and replace if necessary.
For new installations, assemble the faucet to the sink before
installing the sink.
Kohler Co. reserves the right to make revisions in the design of
faucets without notice, as specified in the Price Book.
Adjustable
Wrench Plumbers
Putty Tube Cutter
Plus:
• Water supply
tubes or hoses
1004636-2-E 2 Kohler Co.
1. Install the Spout
IMPORTANT! The maximum sink or counter thickness is 1″(2.5
cm) for this installation.
NOTE: The handspray style may vary. The installation instructions
still apply.
Apply a bead of plumbers putty or other sealant to the underside
of the spout base according to the manufacturer’s instructions.
Thread the shank nut and washer to the bottom of the shank
until the nut touches the top of the shank tee.
Insert the shank from the bottom of the sink.
Thread the shank into the bottom of the spout between 16 and 19
turns so it is hand tight.
Loosen the shank 1/8 of a turn.
IMPORTANT! Do not loosen the shank more than 1/2 turn. The
spout may not seal, resulting in a leak.
Tighten the shank nut and washer to secure the shank to the sink.
2. Install the Handspray
Slide the gasket, if provided, onto the spray holder. If a gasket is
not provided, apply plumbers putty to the underside of the spray
holder.
Slide the spray holder through the mounting hole from above.
Spout
Base
Handspray
Spray Holder
Mounting Hole
Spray Holder Nut
Shank
Shank Tee
Handspray Hose
Shank Nut
Washer
Sink
Spout
Apply plumbers putty.
Kohler Co. 3 1004636-2-E
Install the Handspray (cont.)
Hand tighten the spray holder nut from under the sink.
If applicable, remove any excess plumbers putty.
Insert the handspray hose through the spray holder.
Attach the handspray hose to the shank tee.
Wrench tighten the spray holder nut.
1004636-2-E 4 Kohler Co.
3. Install the Valve Body
Apply a bead of plumbers putty or other sealant to the underside
of the escutcheons according to the manufacturer’s instructions.
Thread the hoses to the valve body outlets and wrench tighten.
Do not overtighten.
Insert the valve bodies into the mounting holes from the top of
the sink. Make sure the hot valve body is installed in the
left-hand hole and the cold valve body is installed in the
right-hand hole.
Install a washer and then a nut to the bottom of the valve bodies.
Align the valve bodies so the copper tubing faces the outside.
Wrench tighten the nuts.
Remove any excess plumbers putty.
Connect and wrench tighten the hoses to the shank tee. Do not
overtighten.
Escutcheon
Hose
Nut
Shank
Tee
Washer
Apply
plumbers
putty.
Valve Body
Kohler Co. 5 1004636-2-E
4. Install the Supplies
NOTE: If the sink is not installed, install it at this time. Be sure to
follow all instructions packed with the sink.
For ground joint connections:
Determine the correct length needed for the supply tubes (not
included).
Cut the supply tubes using a tube cutter.
Remove any burrs or sharp edges.
Slip a nut and ferrule onto each supply tube.
Securely tighten all nuts.
Carefully insert a supply tube into each supply water outlet.
Align each ferrule with the supply water outlet.
If the connection is a union connection, align and center the cone
on each valve fittings and hand tighten the nut.
If it is a compression connection, align and center a ferrule on
each valve fitting and hand tighten the nuts.
Wrench tighten all nuts. Do not overtighten.
For hose connections (not shown):
Attach one end of a hose (not supplied) to the hot valve and one
end to the hot supply.
Compression
Union
Nut
Cone
Nut
Ferrule
Valve Fitting
Supply Tube
Hot
Supply
Cold
Supply
1004636-2-E 6 Kohler Co.
Install the Supplies (cont.)
Attach one end of a hose (not supplied) to the cold valve and one
end to the cold supply.
Carefully tighten all connections.
Kohler Co. 7 1004636-2-E
5. Installation Checkout
Ensure that both faucet handles are turned off. Hot is clockwise
close and cold is counterclockwise close.
Turn on the hot and cold water supplies.
Check for leaks.
Remove the aerator body, aerator insert, and washer from the
spout by turning it counterclockwise.
Turn on the hot and cold faucet handles.
Run the water for about one minute to remove any debris.
Turn off the hot and cold faucet handles.
Place the aerator insert and then the washer into the aerator body.
Reinstall the aerator by turning it clockwise until hand tight.
Check for leaks.
Washer
Aerator Insert
Aerator
Body
1004636-2-E 8 Kohler Co.
Guide d’installation
Robinet d’évier de cuisine
Outils et matériels
Merci d’avoir choisi la compagnie Kohler
Nous apprécions votre engagement envers la qualité Kohler. Veuillez
prendre s’il vous plaît quelques minutes pour lire ce manuel avant de
commencer l’installation. Ne pas hésiter à nous contacter en cas de
problème d’installation ou de performance. Nos numéros de téléphone
et notre adresse du site internet sont au verso. Merci encore d’avoir
choisi la compagnie Kohler.
Avant de commencer
Respecter tous les codes de plomberie et de bâtiment locaux.
Couper les alimentations d’eau.
Avant l’installation, déballer le nouveau robinet et l’examiner
pour en déceler tout dommage. Remettre le robinet dans son
emballage de protection jusqu’à être prêt à l’installation.
Vérifier avec soin si l’évacuation ou les tubes d’alimentation pour
déceler tout signe d’endommagement et remplacer si nécessaire.
Pour de nouvelles installations, installer le robinet sur l’évier
avant d’installer ce dernier.
Clé à
molette Mastic de
plombier Coupe-tubes
Plus:
• Tubes ou tuyaux
d'alimentation d'eau
Kohler Co. Français-1 1004636-2-E
Avant de commencer (cont.)
Kohler Co. se réserve le droit d’apporter toutes modifications au
design des robinets et ceci sans préavis, comme spécifié dans le
catalogue des prix.
1004636-2-E Français-2 Kohler Co.
Este manual sirve para los siguientes modelos
5
Tabla de contenidos
Idiomas:
Otros manuales de Accesorios de cocina y baño de Kohler
Kohler
Kohler K-2268 Instrucciones de montaje
Kohler
Kohler K-1109 Manual de usuario
Kohler
Kohler Archer K-11076-4 Instrucciones de montaje
Kohler
Kohler Prologue K-3592 Instrucciones de montaje
Kohler
Kohler C3-035 Manual de usuario
Kohler
Kohler K-8022 Manual de usuario
Kohler
Kohler BEITOU Manual de usuario
Kohler
Kohler ALEO 98867M-4 Manual de usuario
Kohler
Kohler K-498 Manual de usuario
Kohler
Kohler 6528-PB Manual de usuario
Kohler
Kohler K-15270 Manual de usuario
Kohler
Kohler C3-520 Manual de usuario
Kohler
Kohler Coralais K-15179 Manual de usuario
Kohler
Kohler ARTIFACTS 72762T-9M Manual de usuario
Kohler
Kohler LOURE K-98454T-NW-CP Manual de usuario
Kohler
Kohler K-T10110 Manual de usuario
Kohler
Kohler LOURE 98454T-CP Manual de usuario
Kohler
Kohler JULY 16084T-B4 Manual de usuario
Kohler
Kohler K-16012 Manual de usuario
Kohler
Kohler Sterling 7110 Series Manual de usuario
Manuales populares de Accesorios de cocina y baño de otras marcas
Alpha Bidet
Alpha Bidet Alpha One Manual de usuario
InSinkErator
InSinkErator H/HC3300 Manual de instalación
Clou
Clou Xo type 1 Manual de usuario
Grohe
Grohe Bridgeford 20 158 Manual de usuario
Hans Grohe
Hans Grohe Croma Select S 180 Showerpipe EcoSmart... Manual de usuario
Wickes
Wickes MONO SINK MIXER Manual de usuario