Kohler K-1106 Instrucciones de montaje

Homeowners Guide

Bath Whirlpools

K-1106, K-1112, K-1114,

K-1126, K-1131, K-1139,

K-1144, K-1146, K-1148,

K-1154, K-1157, K-1160,

K-1162, K-1164, K-1192,

K-1194, K-1196, K-1198,

K-1201, K-1209, K-1221,

K-1224, K-1226, K-1231,

K-1239, K-1244, K-1246,

K-1248, K-1257, K-1263,

K-1266, K-1337, K-1477,

K-1630, K-1635, K-1683,

K-1684

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de Mcorresponden a México

(Ej. K-12345M)

Français, page “Français-1”

Español, página “Español-1”

1010564-5-J

Operating Instructions

INSTRUCTIONS PERTAINING TO A RISK OF FIRE,

ELECTRICAL SHOCK, OR INJURY TO PERSONS

READ AND FOLLOW ALL INSTRUCTIONS

SAVE THESE INSTRUCTIONS

WARNING: When using electrical products, basic precautions should always be followed,

including the following:

DANGER: Risk of personal injury. To reduce the risk of injury, do not permit children to use this

unit unless they are closely supervised at all times.

WARNING: Risk of personal injury. To avoid injury, exercise care when entering or exiting the

whirlpool.

WARNING: Risk of electric shock. Do not permit electric appliances (such as a hair dryer, lamp,

telephone, radio, or television) within 5’ (1.5 m) of this whirlpool.

WARNING: Risk of hyperthermia. People using medications and/or having an adverse medical

history should consult a physician before using a whirlpool equipped with a heater.

Use this whirlpool only for its intended purpose as described in this manual. Do not use attachments not

recommended by the manufacturer.

Never drop or insert any object into any opening.

Do not operate this unit without the guard (cover) over the suction ﬁtting.

The whirlpool must be connected only to a supply circuit that is protected by a Ground-Fault

Circuit-Interrupter (GFCI) or Earth-Leakage Circuit-Breaker (ELCB). Such a GFCI or ELCB should be

provided by the installer and should be tested on a routine basis. To test the GFCI or ELCB, press the test

button. The GFCI or ELCB should interrupt power. Press the reset button. Power should be restored. If the

GFCI or ELCB fails to operate in this manner, the GFCI or ELCB is defective. If the GFCI or ELCB interrupts

power to the bath without the test button being pressed, a ground current is ﬂowing, indicating the

possibility of an electric shock. Do not use this whirlpool bath. Disconnect the whirlpool and have the

problem corrected by a qualiﬁed service representative before using.

NOTE: If the pump supply cord is damaged, it must be replaced by the manufacturer, its service agent or

similarly qualiﬁed persons in order to avoid a hazard. The heater supply cord cannot be replaced. If the

cord is damaged the heater should be scrapped.

WARNING: The use of alcohol, drugs, or medication can greatly increase the risk of fatal

hyperthermia. Prolonged immersion in hot water may induce hyperthermia. Hyperthermia occurs

when the internal temperature of the body reaches a level several degrees above the normal body

temperature of 98.6°F (37°C). The symptoms of hyperthermia include an increase in the internal

temperature of the body, dizziness, lethargy, drowsiness, and fainting. The effects of hyperthermia

include: (a) failure to perceive heat, (b) failure to recognize the need to exit the bath, (c) unawareness

of impending hazard, (d) fetal damage in pregnant women, (e) physical inability to exit the bath, and

(f) unconsciousness resulting in the danger of drowning.

IMPORTANT! Flush your whirlpool system twice a month or more depending upon usage, as described

in cleaning instructions in this manual.

Do not allow the water temperature in the whirlpool to exceed 104°F (40°C).

Keep small objects such as bath toys and bathing accessories out of the whirlpool while the unit is running.

1010564-5-J 2 Kohler Co.

Operating Instructions (cont.)

Repeated use of personal care products containing oils can damage plastic whirlpool components. Do not use

heavy, vegetable-based shampoos or bath oils.

Whirlpool hydro-massage action can cause even a small amount of bubble bath, bath soap, shampoo, or bath

oil to foam excessively. For this reason, please don’t use these products during whirlpool operation.

Your new Kohler whirlpool has been listed by Underwriter’s Laboratories, ensuring safety for you and your

family. This whirlpool also conforms to rigid ANSI and IAPMO standards set within the plumbing industry.

Table of Contents

Operating Instructions ............................................................. 2

Thank You For Choosing Kohler Company .............................................. 3

Your Kohler Whirlpool ............................................................. 3

Operating Your Whirlpool ........................................................... 4

Cleaning Your Whirlpool ............................................................ 4

Flushing Your Whirlpool System ...................................................... 5

Limited One-Year Warranty - For U.S.A. and Canada ...................................... 5

One-Year Warranty - For Mexico ..................................................... 5

Troubleshooting Procedures ......................................................... 6

Service Parts .................................................................... 8

Thank You For Choosing Kohler Company

Thank you for choosing the Bold Look of Kohler. Kohler craftsmanship offers you a rare combination of

proven performance and graceful sophistication that will satisfy you for years to come. The dependability

and beauty of your Kohler product will surpass your highest expectations. We’re very proud of our products

here at Kohler and we know you will be too.

Please take a few minutes to study this Homeowners Guide. Pay special attention to the care and cleaning

instructions.

All information in this manual is based upon the latest product information available at the time of

publication. At Kohler, we constantly strive to improve the quality of our products. We reserve the right to

make changes in product characteristics, packaging or availability at any time without notice.

Your Kohler Whirlpool

Your new whirlpool is designed to stimulate, invigorate, and energize your body with comforting

hydro-massage therapy. The whirlpool consists of the following components:

•Bath - acts as a reservoir for water, and provides a location for the hydro-massage action.

•Air Actuator Control - located within easy reach, the air actuator control turns the whilrpool on and

off through the activation of a reliable sensing device.

•Pump Motor - provides quiet power to circulate the water and create the soothing hydro-massage

action.

•Adjustable Jets - positioned to optimize their hydro-massage effect, the jets allow you to adjust the

air and water ﬂow and control the ﬂow direction as you desire.

Your whirlpool may also include the following features:

•Heater, ″H″models only (available in most markets) - designed to automatically help maintain the

temperature of the water up to 104°F (40°C) to enhance your hydro-massage experience. The heater

turns on automatically when the whirlpool is running, and turns off when the pump motor is

turned off.

•Timer Kit (available as an optional accessory) - automatically stops the pump after about 20

minutes of continuous whirlpool operation.

•Integral or Removable Apron (available on select models) - designed to complement the style and

contours of your whirlpool. The whirlpool apron also provides easy frontside access to the pump

and controls in case servicing is necessary.

Kohler Co. 3 1010564-5-J

Operating Your Whirlpool

Position the jet nozzles so they face down toward the basin. Turn the jet trim rings fully

counterclockwise.

NOTE: The water temperature in the whirlpool should never exceed 104°F (40°C).

Close the drain, and ﬁll the whirlpool to a level at least 2” (5.1 cm) above the top of the highest jet.

Use your hand to test the water temperature for comfort and safety, then carefully enter the bath

basin.

Press the air actuator to turn on the whirlpool.

NOTE: If equipped, the heater will also turn on.

Adjust the jets for optimum air/water mixture. Turn the jet trim rings clockwise to reduce the ﬂow,

and counterclockwise to increase the ﬂow. Position the jet nozzles to direct the water ﬂow as desired

to maximize your hydro-massage experience.

Press the air actuator a second time to turn off the whirlpool.

Carefully exit the bath, and open the drain to empty the whirlpool.

NOTE: If your whirlpool includes an optional timer kit, the whirlpool will turn off after approximately 20

minutes of continuous operation. You can then restart the whirlpool if you desire by pressing the air

actuator.

NOTE: If the whirlpool does not function properly, please refer to the Troubleshooting section.

Cleaning Your Whirlpool

For best results, keep the following in mind when caring for your KOHLER product:

•Use a mild detergent such as liquid dishwashing soap and warm water for cleaning. Do not use

abrasive cleaners that may scratch or dull the surface.

•Carefully read the cleaner product label to ensure the cleaner is safe for use on the material.

•Always test your cleaning solution on an inconspicuous area before applying to the entire surface.

•Do not allow cleaners to sit or soak on the surface.

•Wipe surfaces clean and rinse completely with water immediately after cleaner application. Rinse

and dry any overspray that lands on nearby surfaces.

•Use a soft, dampened sponge or cloth. Never use an abrasive material such as a brush or scouring

pad to clean surfaces.

For detailed cleaning information and products to consider, visit www.kohler.com/clean. To order Care &

Fill with water at least 2" (5.1 cm)

above the highest jet.

Turn the jet trim ring

clockwise to

decrease the flow. Position the jet

nozzles to direct

the water flow as

desired.

Turn the jet trim ring counterclockwise

to increase the flow.

Press the air switch to turn the

whirlpool on or off.

1010564-5-J 4 Kohler Co.

Cleaning Your Whirlpool (cont.)

Cleaning information, call 1-800-456-4537 and press 1 for Kohler Products and then 3 for Literature.

Flushing Your Whirlpool System

Flush your whirlpool system twice a month or more, depending upon usage. Use the following

sequence:

•Turn the jet trim rings fully clockwise to reduce air induction.

•Fill the whirlpool with hot water to a level at least 2″(5.1 cm) above the highest jet.

•Add 2 tablespoons (30 ml) of a low-foaming dishwasher detergent and 20 ounces (590 ml) of

household bleach (5% - 6% sodium hypochlorite) to the water.

•Run the whirlpool for 5 to 10 minutes. Turn off the whirlpool and drain.

•If desired, rinse the bath surfaces with water.

•Rinse the surfaces of the jets, faucet, handrails, drain, etc. and wipe them dry with a soft cloth.

Limited One-Year Warranty - For U.S.A. and Canada

For the USA and Canada Only

KOHLER plumbing products are warranted to be free of defects in material and workmanship for one year

from date of installation.

Kohler Co. will, at its election, repair, replace or make appropriate adjustment where Kohler Co. inspection

discloses any such defects occurring in normal usage within one (1) year after installation. Kohler Co. is not

responsible for removal or installation costs.

To obtain warranty service contact Kohler Co. either through your Dealer, Plumbing Contractor, Home

Center or E-tailer, or by writing Kohler Co., Attn.: Customer Service Department, 444 Highland Drive,

Kohler, WI 53044, USA, or by calling 1-800-4-KOHLER from within the USA, 1-800-964-5590 from within

Canada and 001-877-680-1310 from within Mexico.

Implied warranties including that of merchantability and ﬁtness for a particular purpose are expressly

limited in duration to the duration of this warranty. Kohler Co. and/or seller disclaims any liability for

special, incidental or consequential damages.

Some states/provinces do not allow limitations on how long an implied warranty lasts, or the exclusion or

limitation of special, incidental or consequential damages so these limitations and exclusions may not apply

to you. This warranty gives you speciﬁc legal rights. You may also have other rights which vary from

state/province to state/province.

This is Kohler Co.’s exclusive written warranty.

One-Year Warranty - For Mexico

For Mexico Only

KOHLER CO.

It is recommended that at the time of purchase, you verify that all accessories and components are complete

in this package.

This Kohler product is warranted to be free of defects in material and workmanship for one (1) year from the

date of purchase as shown on the invoice or receipt.

1. Kohler Co. will only service its commercialized products through its authorized distributors.

2. To obtain warranty service, please present the invoice and corresponding warranty.

3. Through its authorized distributors, Kohler Co. promises to repair the defective product or provide a new

replacement or an equivalent model (in those cases that the model has been discontinued) when the product

is beyond repair, without any charge to the consumer.

Kohler Co. 5 1010564-5-J

One-Year Warranty - For Mexico (cont.)

4. The time of repair will not exceed six (6) weeks commencing on the date the product is received.

5. It is recommended that the consumer save the invoice or receipt as additional protection, as it may

substitute the warranty in the case that there is a discrepancy in the validity of the warranty.

EXCEPTIONS AND RESTRICTIONS

The Warranty will not be valid in the following cases:

1. When the product is not operated in accordance with the instructions concerning use and operation set

forth in the owner’s manual or installation instructions, and when the recommendations and warnings

included are not observed.

2. When the product has been modiﬁed or dismantled partially or totally; or has been used in a negligent

fashion and as a consequence has suffered damages attributable to the consumer, individual, or hardware not

authorized by Kohler Co.

3. This warranty does not cover the damages as a result of disaster such as ﬁre or acts of God, including

ﬂooding, earthquake, or electric storms, etc. To obtain a list of distributors in your area where you can

exercise your rights under this warranty, please call 001-877-680-1310.

KOHLER CO., KOHLER, WI 53044 U.S.A.

IMPORTER:

INTERNACIONAL DE CERÁMICA, S.A.B. DE C.V.

AV. CARLOS PACHECO NO. 7200

CHIHUAHUA, CHIH., MEXICO C.P. 31060

TEL: 52 (14) 29-11-11

Troubleshooting Procedures

This troubleshooting guide is for general aid only. A Kohler Authorized Service Representative or qualiﬁed

electrician should correct any electrical problems. For warranty service, contact your dealer or wholesale

distributor.

Symptoms Probable Causes Recommended Action

1. Whirlpool will not

start/stop. A. No power to pump. A. Verify pump is plugged in and

the GFCI/ELCB is not tripped.

Verify the outlet has power using

a multi-meter or by connecting a

110V item that you know is

working (lamp, radio, etc.) into

the outlet. Repair as needed.

B. Remove the access panel and

press the air switch, if you do not

hear a ″click,″the air switch

tubing is loose or disconnected.

B. Check if the air switch tubing is

connected at both the

receiver/pump end and the air

switch. Reconnect if needed.

C. Air switch tubing is pinched or

kinked. C. Adjust tubing to clear the

pinched/kinked area. If the

pinch/kink cannot be ﬁxed, or

no noticeable pinch/kink is

apparent, puncture the tubing

with a tack and try the system

again.

D. Push button assembly is damaged. D. Replace the push button

assembly.

E. Pump has power and a ″click″is

heard when the air switch is

pressed. Pump is defective.

E. Replace the pump.

1010564-5-J 6 Kohler Co.

Troubleshooting Procedures (cont.)

Symptoms Probable Causes Recommended Action

F. The receiver in the pump is

defective. F. Replace the receiver or pump.

G. System has a timer kit and the

pump is not switched to the ON

position.

G. Refer to the timer kit installation

instructions.

2. The system will start but

will not stay ON. A. The receiver in the pump is

defective. A. Replace the receiver or pump.

3. Whirlpool stops

automatically. A. System includes an integral timer

and will turn off automatically

after 18 minutes.

A. Verify your system has an

integral timer, if yes, no

additional action is needed.

B. Pump has overheated and the

protection devices has activated. B. Check for blockage at the motor

vents. Check for suction

blockage. Check for jet blockage.

Remove any blockage and allow

the motor to cool.

C. GFCI/ELCB circuit has tripped. C. Identify source fault and correct.

Check that the GFCI/ELCB has

not been tripped. If problem

persists, contact an electrician.

4. The motor starts but not

all jets fuction. A. Jets are closed. A. Rotate the jet trim ring

counterclockwise to

open/increase ﬂow to the jets.

B. Jets are blocked or trim ring

rotation is impeded. B. Glue may be obstructing the jet

opening or preventing the jet

trim ring from rotating. Remove

the trim ring and remove excess

glue.

C. Jets not installed correctly. C. Reinstall the jet; check for any

O-ring damage.

D. Pump is not supported correctly

and is cavitating. D. Review the installation

instructions and verify that the

pump is a the appropriate height

and tat the pump banding straps

(when applicable) have been cut.

5. Noisy pump operation. A. The pump banding straps have

not been cut (models with support

blocks only).

A. Using tin snips, cut pump

banding straps.

6. Heater does not operate

(units with heaters only). A. No power to heater or it is not

connected to a separate outlet

from the pump.

A. Verify that the heater is

connected to a separate outlet

from the pump and that the

connection has power.

B. The water temperature is above

104°F (40°C). B. As a safety precaution, the heater

will not operate when the water

temperature is above 104°F

(40°C).

Kohler Co. 7 1010564-5-J

Service Parts

**Finish/color code must be specified when ordering.

34353

O-Ring

67429

Flange

65885

Gasket

67889

Jet Housing

91967

Check Valve

30739

Jet Tool

1045715-P

Silicone

Lube Packet

67665

Plug

94469

Flange Removal

Tool

Single Jet For Whirlpools

With 5 or Less Jets

Single Jet For Whirlpools

With 6 or More Jets

1011031**

88531**

Jet

1011032**

88529**

(Colored Finishes)

(Metal Finishes)

(Colored Finishes)

(Metal Finishes)

Jet

93836

93838

93839

94853

(1/2")

(1")

(1-1/4")

(1-1/2")

Tube (w/Couplings)

93685

Housing

96708

Flange

96895**

65061**

Cover

65886

60050

(Colored Finishes)

(Metal Finishes)

(Acrylic and FRP)

(For Other Product)

Gasket

65054**

Screw

65226**

Suction Cover Plug

73518

Plug

1003065

Suction Flange

Removal Tool

1009718

(230 V, Canada)

(120 V, Canada)

In-line Heater

1012977

Adapter

1012653

Adapter

1011679

Gasket

94821

O-Ring

1012916

Nut w/Screws

1012916

Nut w/Screws

1009719 (120 V, Canada)

In-line Heater

1009720 (230 V)

In-line Heater

1012653

Adapter

94821

O-Ring

94821

O-Ring

1012653

Adapter

94821

O-Ring 1012916

Nut w/Screws

1010031 (120 V, USA and Mexico)

Tee Heater

1010032

Tee Heater

1012977

Adapter

94821

O-Ring

94821

O-Ring

1012977

Adapter

1012916

Nut w/Screws

1010033

(120 V, USA and Mexico)

Tee Heater

1012977

Adapter

1012653

Adapter

94821

O-Ring

94821

O-Ring

1012856

O-Ring

94821

O-Ring

94821

O-Ring

1012977

Adapter

1012977

Adapter

1012855

Union Nut

1012916

Nut w/Screws

1012916

Nut w/Screws

1011679

Gasket

1012301

Connector

1010564-5-J 8 Kohler Co.

1005363

Slip Nut

94821

O-Ring

1034673

Connector

60980

O-Ring

1010029

Tee

1010672

Air Switch

1010677

Screw

1010676

Cover

1010675

O-Ring

1010677

Screw

1010676

Cover

1010675

O-Ring

1010673

Seal

1010673

Seal 1013755

Impeller

1010674

Impeller

1015057

Screw

1015058

Cover

1009763

Motor/Control

1010548

Volute

1010548

Volute

1008235 (230 V)

(230 V)

1010547

Motor/Control

(Canada)

1010546 (120 V, USA and Mexico)

1008234

Pump

(120 V, Canada)

1008233 (120 V, USA and Mexico)

Pump

**Finish/color code must be specified when ordering.

See supporting

pump details.

1041995**

Air Switch

1054431

Receiver Switch

1054436

Wet End

1054430

Pump

(120 V, Canada)

1052586 (120 V, USA and Mexico)

Kohler Co. 9 1010564-5-J

1012855

Nut

1012301

Connector

1012856

1010999

Screw

1011002

1012854

Tee

1012856

O-Ring

1012297

Impeller

Volute Cover

1010998

1012298

Seal

1012299

Volute

Air Pressure Switch

1012857

73515-C

Nut

1012859

Pump

1012300

Motor

1010672

1012296

1012858

Cord

1012855

Nut

1012301

Connector

1012856

1010999

Screw

1011002

1012854

Tee

1012856

1012297

Impeller

1015436

1012298

Seal

1015435

Volute

1015434

Nut

1008232

Pump

1015437

Motor

Noise Isolator

1010672

1012296

1014347

Cord

**Finish/color code must be specified when ordering.

(120 V, USA and Mexico)

(120 V, Canada)

Lock Washer

1043366

Pump

1043365

Pump

To Air Switch

To Heater (if applicable)

1010564-5-J 10 Kohler Co.

Otros manuales para K-1106

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Jacuzzi de Kohler

Kohler

Kohler Purist K-1110-M Manual de usuario

Kohler

Kohler ENGLEFIELD T1180-CP Guía de instalación

Kohler

Kohler K-1025-H2 Manual de usuario

Kohler

Kohler Stargaze K-1958-GW Manual de usuario

Kohler

Kohler K-1110 Manual de usuario

Kohler

Kohler Whirlpool Baths Manual de usuario

Kohler

Kohler SA Series Manual de usuario

Kohler

Kohler K-1418-AH Instrucciones de montaje

Kohler

Kohler K-1110-CT Instrucciones de montaje

Kohler

Kohler K-1111-VLN-0 Manual de usuario

Kohler

Kohler Portrait K-1457-H2 Guía de inicio rápido

Kohler

Kohler MASSDREAM Manual de usuario

Kohler

Kohler K-1753T Manual de usuario

Kohler

Kohler K-1152-L Guía de inicio rápido

Kohler

Kohler K-1394 Series Manual de usuario

Kohler

Kohler K-1160P Guía de inicio rápido

Kohler

Kohler K-1703 Manual de usuario

Kohler

Kohler Tea-For-Two K-852-V-AB Manual de usuario

Kohler

Kohler K-856-V-G9 Instrucciones de montaje

Kohler

Kohler VINTAGE K-7158 Manual de usuario

Kohler

Kohler K-702 Manual de usuario

Kohler

Kohler K-1418-CT Instrucciones de montaje

Kohler

Kohler BodySpa K-1000 Manual de usuario

Kohler

Kohler K-1418-V Instrucciones de montaje

Manuales populares de Jacuzzi de otras marcas

Bestway

Bestway Lay-Z-Spa 54189 Manual de usuario

Jacuzzi

Jacuzzi ARGA ARG101C0110 Manual de lista de piezas

Morphy Richards

Morphy Richards Essentials PC4006 Manual de usuario

Softub

Softub PRESTIGE Manual de usuario

JNJ SPAS

JNJ SPAS SPA-318 Manual de instalación

KIRAMI

KIRAMI Comfort Family Manual de usuario

QCA Spa

QCA Spa VS501 PAK (VL260 TOPSIDE) Manual de usuario

HoMedics

HoMedics FB-655HJ-GB Manual de usuario

Everyday Hot Tubs

Everyday Hot Tubs 530 Manual de usuario

anko

anko SS-601A Manual de usuario

Jacuzzi

Jacuzzi Duetta 6042 Manual de usuario

Pooli

Pooli OS030979B Manual de usuario

Jacuzzi

Jacuzzi alimia Manual de usuario

ab Solares Smart Spa Manual de usuario

CalderaSpas

CalderaSpas CalderaSpas Utopia Series Manual de usuario

Outsunny

Outsunny 848-047V70 Manual de usuario

Aquatic

Aquatic INFINITY 1 Manual de usuario

Master Spas

Master Spas MP Force Manual de usuario