Kohler K-T10185 Manual de usuario
Installation Guide
Three-way Transfer Valve Trim
K-T376, K-T10185, K-T10113,
K-T10290, K-T10304, K-T10340,
K-T10424, K-T10429, K-T10595,
K-T10682, K-T10944, K-T12189,
K-T13175, K-T14491, K-T16178,
K-T16242, K-T18491
Mproduct numbers are for Mexico (i.e. K-12345M)
Los números de productos seguidos de
Mcorresponden a México (Ej.
K-12345M)
Français, page “Français-1”
Español, página “Español-1”
1041514-2-J
Thank You For Choosing Kohler Company
Thank you for choosing Kohler Company. Your Kohler Company
product reflects the true passion for design, craftsmanship, artistry, and
innovation Kohler Company stands for. We are confident its
dependability and beauty will surpass your highest expectations,
satisfying you for years to come.
All the information in this guide is based upon the latest product
information available at the time of publication. At Kohler Company,
we strive to fulfill our mission of improving the level of gracious living
for each person who is touched by our products and services. We
reserve the right to make changes in product characteristics, packaging,
or availability at any time without notice.
Please take a few minutes to review this guide. If you encounter any
installation or performance problems, please call 1-800-4KOHLER
(1-800-456-4537) from within the USA and Canada, or 001-877-680-1310
from within Mexico.
Tools and Materials
Before You Begin
Shut off the main water supply.
Observe all local plumbing and building codes.
The trim design illustrated in this guide is representative and
may differ from the actual trim being installed. Install the trim as
instructed.
Kohler Co. reserves the right to make revisions in the design of
products without notice, as specified in the price book.
Screwdrivers Hex
Wrenches
1041514-2-J 2 Kohler Co.
1. Install the Valve Stem Adapter
NOTE: Check the finished wall surface as related to the graphics on
the plaster guard.
Select the correct length valve stem adapter and valve stem
adapter screw for your application. Refer to the information
stamped on the plaster guard to verify the wall thickness.
For a thin wall - 3/16″(5 mm) to 9/16″(1.4 cm):use the 1/2″(1.3
cm) (short size) valve stem adapter, stamped ″3″on the plaster
guard, and the 13/16″(2.1 cm) screw.
For a standard wall - 9/16″(1.4 cm) to 1-1/16″(2.7 cm):use the 7/8″
(2.2 cm) (middle size) valve stem adapter, stamped ″1″on the
plaster guard, and the 13/16″(2.1 cm) screw.
For a thick wall - 1-1/16″(2.7 cm) to 1-9/16″(4 cm):use the 1-3/8″
(3.5 cm) (long size) valve stem adapter, stamped ″2″on the plaster
guard, and the 1-3/8″(3.5 cm) screw.
Remove and discard the plaster guard from the transfer valve.
Place the spline adapter over the valve stem.
Set the correct valve stem adapter over the valve stem. Do not
completely press or screw the valve stem adapter into place
until instructed to do so.
Select the correct
valve stem adapter.
Remove and discard
the plaster guard.
Transfer
Valve
Spline
Adapter
Valve Stem
Adapter
Kohler Co. 3 1041514-2-J
2. Adjust the Handle Assembly
NOTE: Valve Operation. Water will flow from a single shower
accessory when the control knob detent lines up with any of the
large detents on the escutcheon. Water will flow from two
accessories at the same time when the control knob detent lines up
with a small escutcheon detent.
Ensure the valve stem adapter is lightly placed over the spline
adapter.
Place the handle assembly over the valve stem adapter.
Turn on the water supply to the transfer valve.
Rotate the handle assembly until water begins to flow through
the shower accessory.
Determine the shower accessory that will correspond to the
Accessory ″A″setting at the 12 o’clock position on the escutcheon.
Turn the handle to the detent setting that corresponds with
Accessory ″A.″The handle should be in the vertical 12 o’clock
position.
Remove the handle assembly and set aside.
Accessory “A”
Accessory “C”
Accessory “B”
Accessory “A” Accessory “B”
Accessory “C”
Control Knob Detent
Combined Accessories
“A” and “C”
Combined Accessories
“B” and “C”
Combined
Accessories “A”
and “B”
Valve Stem
Adapter
Spline Adapter
Transfer Valve
Handle
Assembly
Mixed Water
Supply
1041514-2-J 4 Kohler Co.
Adjust the Handle Assembly (cont.)
To adjust for handle alignment:
NOTE: The spline adapter allows fine adjustment of the handle
alignment.
Remove the handle assembly and the valve stem adapter.
Reposition the spline adapter.
Reinstall the handle assembly and the valve stem adapter.
Check the alignment. Repeat this procedure until the handle
alignment is satisfactory.
Kohler Co. 5 1041514-2-J
3. Install the Trim
NOTE: If you are installing the K-T10424 trim, proceed to the
″Install the Trim - K-T10424″section of this guide.
Firmly press the valve stem adapter onto the valve stem.
Secure the valve stem adapter to the valve with the correct length
screw, as selected in the ″Install the Valve Stem Adapter″section
of this guide.
Align the holes on the front plate assembly and the valve.
NOTE: Be sure to select the correct length screw for your
application.
Attach the two screws through the front plate assembly and into
the valve. Do not overtighten.
Visually inspect the front plate assembly to ensure that the foam
seal is completely covering the wall opening. If not, stop the
installation and repair the wall opening.
Place the escutcheon against the wall. The drain hole in the
escutcheon should face downward in the 6 o’clock position.
Turn the handle assembly to the vertical 12 o’clock position.
Thread the handle assembly onto the hub of the front plate
assembly to secure the escutcheon in place.
NOTE: If the handle does not engage the valve or the escutcheon
does not tighten to the wall, replace the valve stem adapter with an
adapter of appropriate length.
Transfer Valve
Handle Assembly
Escutcheon
Screw
Valve Stem Adapter
Front Plate
Assembly
Screws
1041514-2-J 6 Kohler Co.
4. Install the Trim - K-T10424
Firmly press the valve stem adapter onto the valve stem.
Secure the valve stem adapter to the valve stem with the correct
length screw, as selected in the ″Install the Valve Stem Adapter″
section of this guide.
Align the holes on the front plate assembly and the valve.
NOTE: Be sure to select the correct length screw for your
application.
Attach the two screws through the front plate assembly and into
the valve. Do not overtighten.
Visually inspect the front seal plate assembly to ensure that the
foam seal is completely covering the wall opening. If not, stop the
installation and repair the wall opening.
Place the escutcheon against the wall. The drain hole in the
escutcheon should face downward in the 6 o’clock position.
Thread the adapter ring onto the hub of the front plate assembly.
Place the handle assembly against the escutcheon by lining up the
pins in the handle assembly with the holes in the escutcheon.
Make sure the handle is in the 12 o’clock position and the
setscrew hole is facing down.
Tighten the setscrew in place with a hex wrench. Make sure the
handle assembly is tight against the escutcheon.
Valve Stem
Adapter
Screw
Transfer Valve
Escutcheon
Front Plate Assembly
Adapter
Ring Handle
Assembly
Setscrew
Screws
Kohler Co. 7 1041514-2-J
Guide d’installation
Garniture de valve de transfert à trois voies
Outils et matériels
Merci d’avoir choisi la compagnie Kohler
Merci d’avoir choisi la compagnie Kohler. Votre produit de la
compagnie Kohler reflète la véritable passion du design, d’artisanat,
d’art et d’innovation représentant la compagnie Kohler. Nous sommes
confiants que sa fiabilité et beauté surpasseront vos exigences les plus
élevées, vous satisfaisant pendant les années à venir.
Toute l’information dans ce guide est basée sur la dernière disponible
au moment de la publication. A la compagnie Kohler, nous aspirons à
remplir notre mission d’améliorer le niveau de vie gracieux pour
chaque individu affecté par nos produits et services. Nous nous
réservons le droit d’apporter des modifications aux caractéristiques,
aux emballages et à la disponibilité des produits à tout moment, et ce
sans préavis.
Veuillez prendre s’il vous plaît quelques minutes pour étudier ce
guide. En cas de problème d’installation ou de performance, veuillez
composer le 1-800-4-KOHLER (1-800-456-4537) à partir des É.U., et
Canada, ou le 001-877-680-1310 à partir du Mexique.
Avant de commencer
Couper l’alimentation d’eau principale.
Respecter tous les codes de plomberie et de bâtiment locaux.
La conception de la garniture illustrée dans ce guide est
représentative et pourrait différer de la garniture actuelle installée.
Installer la garniture tel qu’instruit.
Tournevis Clés
hexagonales
Kohler Co. Français-1 1041514-2-J
Avant de commencer (cont.)
Kohler Co. se réserve le droit d’apporter toutes modifications sur
le design des produits et ceci sans préavis, tel que spécifié dans le
catalogue des prix.
Kohler Co. Français-2 1041514-2-J
1. Installer l’adaptateur de la tige de valve
REMARQUE : Vérifier la surface du mur fini tel que lié aux
graphiques du renfort en plâtre.
Sélectionner la longueur correcte de l’adaptateur de la tige de
valve et la bonne vis de l’adaptateur de la tige de valve pour
votre application. Se référer à l’information estampillée sur le
renfort de plâtre pour vérifier l’épaisseur du mur.
Pour un mur fin - 3/16″(5 mm) à 9/16″(1,4 cm):utiliser l’adaptateur
de tige de valve (le plus court) de 1/2″(1,3 cm), estampillé ″3″sur
le renfort de plâtre, et la vis de 13/16″(2,1 cm).
Pour un mur standard - de 9/16″(1,4 cm) à 1-1/16″(2.7 cm):utiliser
l’adaptateur de tige de valve (moyen) de 7/8″(2,2 cm), estampillé
″1″sur le renfort de plâtre. et la vis de 13/16″(2,1 cm).
Pour un mur épais - 1-1/16″(2,7 cm) à 1-9/16″(4 cm):utiliser
l’adaptateur de tige de valve (long) de 1-3/8″(3,5 cm), estampillé
″2″sur le renfort de plâtre, et la vis de 1-3/8″(3,5 cm).
Retirer et jeter le renfort en plâtre de l’unité de valve de transfert.
Placer l’adaptateur à cannelures sur la tige de la valve.
Placer l’adaptateur de la tige de valve approprié sur la tige de
valve. Ne pas complètement presser ou visser l’adaptateur de la
tige de valve en place avant d’en être instruit.
Retirer et jeter le renfort en plâtre.
Sélectionner l'adaptateur
de tige de valve correct.
Valve de
transfert
Adaptateur à
cannelures
Adaptateur de tige
de robinet
1041514-2-J Français-3 Kohler Co.
Este manual sirve para los siguientes modelos
16
Tabla de contenidos
Idiomas:
Otros manuales de Unidad de control de Kohler
Kohler
Kohler K-528 Manual de usuario
Kohler
Kohler K-2976-KS Instrucciones de montaje
Kohler
Kohler 880A Manual de usuario
Kohler
Kohler K-10949 Manual de usuario
Kohler
Kohler K-304 Instrucciones de montaje
Kohler
Kohler K-307 Manual de usuario
Kohler
Kohler DTV+ Instrucciones de montaje
Kohler
Kohler K-76746GL-NA Manual de usuario
Kohler
Kohler 28209W-NA Manual de usuario
Kohler
Kohler K-11842 Series Instrucciones de montaje
Kohler
Kohler K-5557 Instrucciones de montaje
Kohler
Kohler K-305 Instrucciones de montaje
Kohler
Kohler K-10668 Instrucciones de montaje
Kohler
Kohler K-408 Instrucciones de montaje
Kohler
Kohler K-402 Instrucciones de montaje
Kohler
Kohler K-13516X Instrucciones de montaje
Kohler
Kohler K301 Manual de usuario
Kohler
Kohler GM77177-KP1-QS Manual de usuario
Kohler
Kohler TAUT 73193T-4CD Manual de usuario
Kohler
Kohler K-308 Manual de usuario
Manuales populares de Unidad de control de otras marcas
Festo
Festo Compact Performance CP-FB6-E Manual de lista de piezas
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manual de usuario
JS Automation
JS Automation MPC3034A Manual de usuario
JAUDT
JAUDT SW GII 6406 Series Guía rápida
Spektrum
Spektrum Air Module System Manual de usuario
BOC Edwards
BOC Edwards Q Series Manual de usuario
