Kohler K-T467 Manual de usuario
Installation Guide
Bath/Deck Mount Faucet
Mproduct numbers are for Mexico (i.e. K-12345M)
Los números de productos seguidos de
Mcorresponden a México (Ej.
K-12345M)
Français, page“ Français-1”
Español, página“ Español-1”
K–T467 K–T469
1023371-2-B
Tools and Materials
Thank You For Choosing Kohler Company
We appreciate your commitment to Kohler quality. Please take a few
minutes to review this manual before you start installation. If you
encounter any installation or performance problems, please don’t
hesitate to contact us. Our phone numbers and website are listed on
the back cover. Thanks again for choosing Kohler Company.
Before You Begin
The valve is sold separately. Please read the instructions packed
with the valve for installation procedures.
Please read all instructions before you begin.
Shut off the main water supply.
Observe all local plumbing and building codes.
Complete the finished deck material before installing.
Before installation, unpack the new faucet trim and inspect it for
damage. Return it to the carton until installation.
Kohler Co. reserves the right to make revisions in the design of
faucets without notice, as specified in the Price Book.
Adjustable
Wrench • Rag
Plus:
Tube Cutter
Tape
Measure
Hex
Wrench Assorted
Screwdrivers
File
Plumbers
Putty
1023371-2-B 2 Kohler Co.
1. Remove the Plug
WARNING: Risk of personal injury. Lines may be pressurized.
Do not lean over the pipe plug when turning or removing the
plug.
Make sure the valves are closed (cold = fully counterclockwise;
hot = fully clockwise).
Turn off the main water supply.
Wrap a rag around the pipe plug to prevent water spray.
IMPORTANT! Water may purge from the supply tube when you
remove the plug.
Carefully remove the pipe plug.
Pipe Plug
Close
Hot
Close
Cold
Kohler Co. 3 1023371-2-B
2. Prepare for Spout Installation
Remove the plaster guard from the spout supply tube.
Cut off the spout supply tube 1-1/4” (3.2 cm) above the rim,
finished deck, or tile.
Remove all burrs from the spout supply tube to prevent damage
to the O-ring seal on the spout sleeve assembly.
NOTE: The washer is not needed for rim/finished deck installation.
If the installation includes a tile covered rough deck, slide the
washer, flat side facing forward, onto the spout supply tube.
NOTE: Before installing the spout sleeve assembly, make sure the
O-ring is properly positioned in the groove on the outside of the
sleeve.
Back off the setscrews in the spout sleeve assembly.
With a twisting motion, place the spout sleeve assembly over the
spout supply tube and push down to the deck surface.
Align the sleeve with the setscrews offset from the center (not
facing directly forward or backward) of the spout supply tube.
Tighten the setscrews.
Purge the supply tube of debris.
Rough
Deck
Tile
Finish
1-1/4"
(3.2 cm)
Washer
Spout
Supply
Tube
Rough
Deck
Finished
Deck
1023371-2-B 4 Kohler Co.
3. Install the Spout
CAUTION: Risk of product damage. Use care when installing
the spout assembly to prevent damage to the O-ring seal.
Position the spout on the sleeve, and carefully press down until
the spout contacts the finished deck.
Rotate the spout until it is aligned to face straight forward.
Tighten the setscrew.
Insert the O-ring onto the plug button.
Insert the plug button over the setscrew, flush with the spout
surface.
Setscrew
O-Ring
Plug
Button
Kohler Co. 5 1023371-2-B
4. Install the Classic Handles
Remove the plaster guards.
Close the valves (hot = clockwise, cold = counterclockwise).
Install a stem extension onto each valve stem spline. Make sure
that the splines are engaged.
Thread a handle assembly onto each valve body. Make sure the
splines in the handle and stem extension are engaged.
NOTE: The stem extension allows fine adjustment of the handle
alignment. To adjust, remove the handle and reposition the stem
extension.
Reinstall the handle and check the alignment. Repeat until the
handle alignment is satisfactory.
Cross
Handle
Assembly
Lever
Handle
Assembly
Valve
Stem
Spline
Stem
Extension
Valve
Body
1023371-2-B 6 Kohler Co.
5. Installing Stately Handles
Apply a bead of plumbers putty or other sealant around the
bottom of the escutcheon according to the putty manufacturer’s
instructions.
Position the escutcheons over the valves.
Install the threaded sleeves to the valves. Securely hand tighten.
Fit the handle assemblies over the valves, and align them so the
setscrews are not easily seen. Orient the lever handles with the
levers pointing away from the spout in the closed position.
Tighten the setscrews.
Press a plug button into each setscrew hole.
Remove any excess plumbers putty.
Valve
Setscrew
Setscrew
Escutcheon
Sleeve
Plug
Button
Lever
Handle
Assembly
Plug
Button
Cross
Handle
Assembly
Kohler Co. 7 1023371-2-B
6. Complete the Installation
Turn off the water (hot = clockwise, cold = counterclockwise).
Remove the aerator assembly.
Turn on the main water supply and check for leaks.
Turn on the hot and cold valves and run water through the spout
to remove debris. Check for leaks.
Turn off the hot and cold valves.
Reinstall the aerator assembly.
Spout
Aerator
1023371-2-B 8 Kohler Co.
Guide d’installation
Robinet montage sur baignoire/comptoir
Outils et matériels
Merci d’avoir choisi la compagnie Kohler
Nous apprécions votre engagement envers la qualité Kohler. Veuillez
prendre s’il vous plaît quelques minutes pour lire ce manuel avant de
commencer l’installation. Ne pas hésiter à nous contacter en cas de
problème d’installation ou de fonctionnement. Nos numéros de
téléphone et notre adresse du site internet sont au verso. Merci encore
d’avoir choisi la compagnie Kohler.
Avant de commencer
La valve est vendue séparément. Veuillez s’il vous plaît lire les
instructions d’installation emballées avec la valve.
Veuillez lire toutes les instructions avant de commencer.
Couper l’alimentation d’eau principale.
Respecter tous les codes de plomberie et de bâtiment locaux.
Compléter le matériau du comptoir fini avant d’installer.
Avant l’installation, déballer la garniture du nouveau robinet et
l’examiner pour en déceler tout dommage. Remettre le robinet
dans l’emballage jusqu’à l’installation.
Cléà
molette • Chiffon
Plus:
Coupe-tubes
Mètre
ruban
Clé
hexagonale Tournevis
assortis
Lime
Mastic de
plombier
Kohler Co. Français-1 1023371-2-B
Avant de commencer (cont.)
Kohler Co. se réserve le droit d’apporter toutes modifications au
design des robinets et ceci sans préavis, comme spécifié dans le
catalogue des prix.
1023371-2-B Français-2 Kohler Co.
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Idiomas:
Otros manuales de Accesorio de baño de Kohler
Kohler
Kohler K-8002 Instrucciones de montaje
Kohler
Kohler STERLING 5400 Series Manual de operación
Kohler
Kohler 12879T Manual de usuario
Kohler
Kohler K-14406 Manual de usuario
Kohler
Kohler KARAT K-17399 Manual de usuario
Kohler
Kohler Singuiler 72671T-C9 Manual de usuario
Kohler
Kohler K-842-H2 Instrucciones de montaje
Kohler
Kohler mira GO Manual de usuario
Kohler
Kohler Karat K-17399 Manual de usuario
Kohler
Kohler K-24985K Instrucciones de montaje
Kohler
Kohler K-6816 Manual de usuario
Kohler
Kohler Lakewood K-1649 Manual de usuario
Kohler
Kohler K-922 Manual de usuario
Kohler
Kohler K-T948 Instrucciones de montaje
Kohler
Kohler Margaux K-16238-4 Instrucciones de montaje
Kohler
Kohler 10257T Manual de usuario
Kohler
Kohler K-7223 Manual de usuario
Kohler
Kohler AWAKEN Geometric 72415T-E Manual de usuario
Kohler
Kohler Mira Showers Escape Thermostatic 9.8 kW Manual de usuario
Kohler
Kohler K-484 Manual de usuario
