Kogan KACCTV4CHA Manual de usuario
Table of Contents
Chapter One: Product Introduction......................................................................................................2
1 Brief Introduction.........................................................................................................................2
2 Main Features...............................................................................................................................2
Chapter Two: Hardware........................................................................................................................3
1 Packa e Content...........................................................................................................................3
2 Front Panel Operation...................................................................................................................3
3 Rear Panel of Operation................................................................................................................3
4 Remote Controller.........................................................................................................................3
5 Hard Disk Installation...................................................................................................................4
6 Rear Panel Connection..................................................................................................................4
Chapter Three: Usa e...........................................................................................................................6
1 Brief Introduction.........................................................................................................................6
2 Menu Operations...........................................................................................................................7
Chapter Four: Operations.....................................................................................................................8
1 Turn on..........................................................................................................................................8
2 Preview.........................................................................................................................................8
3 Record.........................................................................................................................................10
4 Camera Control...........................................................................................................................11
5 Motion Detection Settin s..........................................................................................................12
6 Mask Settin ...............................................................................................................................13
7 Playback......................................................................................................................................13
8 Backup........................................................................................................................................14
9 Alarm Settin s.............................................................................................................................14
10 Network Operation...................................................................................................................15
11 Maintenance..............................................................................................................................18
10 Advanced Settin s.....................................................................................................................20
Chapter Five: Appendix......................................................................................................................22
1 Specifications
.......................................................................................................................................................22
2 Methods of Calculatin HDD Capacity......................................................................................24
3 Default Values.............................................................................................................................25
4 Introduction of Mobile Phone Monitorin ..................................................................................27
1
Chapter One: Product Introduction
1 Brief Introduction
This series DVR is a 4-channel playback H.264 main profile standalone DVR with Pentaple functionality:
record, playback, live preview, remote preview and backup supported.
With professional and high performance intelligent audio and video solutions, user-friendly GUI and practical
industrial design, this series DVR is suitable for civil applications such as home, store, internet bars and
small offices as well as for common security and surveillance applications.
2 Main Features
•Compression
4/8 channel PAL/NTSC/SECAM video input and H.264 compression standards with each channel
being compressed independently in real-time CIF resolution, or non-real time D1,2CIF resolution.
4 channel audio input and G.726/ADPCM-IMA compression standards with each channel being
compressed independently in 24Kbps.
Compressed video and audio are synchronous. You can select either mi ed streams or individual
video streams.
Four-level record quality and self-defined bit rate and frame rate settings supported.
Adjustable video parameters.
Multi-area motion detection.
OSD of channel name and time supported.
•Recording
Manual record and schedule record supported. The schedule report types include: timing, motion
detection, alarm, motion detection | alarm.
SATA hard-disk supported.
Backup and clip record files through USB drive, portable USB HDD and USB CD/DVD RW
supported.
•Preview and Playback
Simultaneous output of VGA and TV.
Up to 4 channels playback in fast play mode, slow play mode, rewind and single frame forward
supported.
OSD of channel name and time supported.
Status displaying of local record, alarm and motion detection supported.
•Control
Controlling of PTZ and dome supported.
Controlling multiple DVRs with on RS485 keyboard.
Setting and calling preset, sequence and track supported.
•Alarm
Local alarm (includes e ception and motion detection, video loss and hard disk full) triggered
handling supported.
Alarm linkage: triggered record, linkage alarm output and linkage PTZ preset, sound alarm, report to
alarm center, linkage channel single screen display and e-mail.
•Network
TCP/IP supported.
PPPoE supported.
Dynamic access to IP address, Dynamic Host Configuration Protocol (DHCP) supported.
DDNS supported.
Visit video files in DVR HDD through network neighbourhood supported.
Controlling of PTZ, configuring device parameters, acquiring device status and logs, and upgrade
remotely through network supported.
Local recording through network supported.
2
Chapter Two: Hardware
This chapter is a general description of the device interfaces and connections. It describes the methods of
hard disk installation, the interface of the front panel and the rear panel for users to connect the cables
correctly.
1 Packa e Content
After purchasing the DVR product, unpack it and unload it flat onto the floor or a place where it is to be
located, and refer to the “Package Contents” for the correct number of device fittings.
2 Front Panel Operation
Table 1 – Front Panel Description
Type Name Description
LED
Power Red when recording. Green when not recording.
HDD Hard disk indicator. Green or blinking when reading/writing.
Black when idle.
3 Rear Panel of Operation
Table 2 – Rear Panel Description
NO. Interface Description
1 Video In 4/8 channel video input: BNC (1Vp_p, 75Ω)
2 TV Out 1 channel TV output, BNC (1Vp-p, 75Ω)
3 Audio Out 1 channel audio output, BNC (2Vp-p, 600Ω)
4 Audio In 4 channels audio input: RCA (2Vp-p, 600Ω)
5 VGA Output 1: DIN-15
6
Network Interface 1: RJ45 10/100M self-adaptive
USB Interface 2: USB 2.0
7 RS485 1: Half Duple ( + - )
8 Power DC 12V
4 Remote Controller
Table 3 – Remote Controller Description
NO. Name Description
1 REC Record
2 Power ON/OFF Turn the device off or on.
3 Numbers Input numbers or select to switch among relevant channels.
4 Function Buttons DEL: Delete
5 Arrow Buttons When in menu mode, press [◄ ], [► ] to move to selection bo es.
Press [▲ ], [▼ ] to select sub-menu parameters.
6 1) Press to confirm operations in menu mode.
2) Press to select record type in setting schedule.
3) Press to change status of the current motion detection block.
3
7 Switch between single screen and multi-screen.
8 FN 1) Press to switch from single split to multi-split view mode, or
reverse in preview and playback mode.
2) Press to enter/e it continuous selection when setting motion
detection area and schedule record.
3) Press to set start time and end time in file search.
9 MENU One key system setup.
10 ESC Return to previous menu.
11 PTZ One key PTZ control.
12 BACKUP Backup Record
13 TV/VGA Switch the operation interface between TV and VGA.
14 CLEAR Alarm Off
15 SEQ Call Sequence
16 1) Play/Pause
2) One key file search
17 Stop
18 Play in slow mode/fast rewind
19 Fast forward
5 Hard Disk Installation
The hard disk is not included in the factory fittings. Users can mount suitable hard disks by calculating its
capacity referring “Appendi 5.2 Methods of Calculating HDD Capacity”.
1) Installation procedure
•Open the DVR case. Mount the 4 shock absorption washers into the clamping slots (four protruding
steps) in the case.
•Connect the HDD data cable and HDD power cable to the HDD.
•Attach the hard disk to the shock absorption washers by aligning the installation holes to the case.
Hold and fi them by 4 M3*12 head screws plus plain washers.
•Connect the HDD data cable and HDD power cable to the respond interfaces of the main board.
•Replace the DVR top cover, then screw it closed.
NOTE: If installing your own HDD, please be sure to purchase a DVR rated HDD instead of a computer rated
HDD. Computer rated HDDs are not designed for continuous DVR use.
NOTE: Please format the HDD for the first use, or the system will return a “Hard Disk Error” notification
accompanied by an audio alarm. Please see 4.9 Maintenance for details.
6 Rear Panel Connection
•Power Input
Connect the power adapter to the Power Input interface of the DVR. Confirm that the DVR power supply
input switch is positioned correctly for the local voltage before connecting and powering the unit.
Turn on the unit. The power LED will light up if the power cable is connected correctly.
NOTE: Please use the power adapter contained in the package.
•Video Input
The video input interface is standard BNC socket, 1Vp-p, 75Ω.
NOTE: The video signal cable should be kept away from the interference of strong electromagnetism and the
city electric power grid.
4
•Audio Input
The audio input interface standard RAC socket, 2Vp-p, 600Ω.
NOTE: The audio input resistance is a little high, please use an active sound collection device or active
microphone. The audio signal cable should be kept away from the interference of strong electromagnetism
and the city electric power grid.
•Network Input
The network input interface is RJ45 10/100M self-adaptive.
NOTE: Confirm that the network band width is enough for transmitting high definite images smoothly.
•Alarm Input and Output
The alarm input device should be the type of GND connected alarm or voltage input alarm, which can be set
as N/O, or N/C.
The requirement of signal input level for voltage alarm type is: low level 0~2V, high level 5~15V.
The green angle pins of the signal cable are designed for access of PTZ and alarming devices. Please
follow these steps to connect.
1. Pull out the angle pins that are inserted in the alarm input and output interfaces.
2. Unscrew the screws with a micro Philips screwdriver, insert the signal cable into the interface under
the spring, then tighten the screws.
3. Plug the connected pins into the green angle pin socket.
•PTZ Input (Pan-Tilt-Zoom)
Connect the PTZ control interface to the RS485 interfaces of the rear panel. The connection method is
similar to the method above.
NOTE: Please refer to the PTZ manual for setting specific parameters, for some PTZ devices contain
multiple telecommunication protocols, baud rates and IDs.
Video Output: VGA/Monitor Input
Video output interface: TV and VGA, which can work together simultaneously.
NOTE: VGA and TV cannot be in the operation interface simultaneously, but can be switched by mouse,
panel or remote control in the menu.
5
Chapter Three: Usa e
1 Brief Introduction
6
2 Menu Operations
Press [SET] button to enter into system setting screen.
Press [●] button to start/stop recording manually.
Press [► ▋▋ ] button to play the recorded file.
Press [PTZ] to enter into the PTZ control screen.
NOTE: This manual indicates the menu selection icons and selection bo es in [XX]; the buttons in the menu
screen (e cept menu selection icons) in [XX]; the buttons on the front panel and remote controller in [XX].
The highlight menu is the current active one. The user can move the highlight icon on the menu by using the
[►], [◄], [▲] and [▼] buttons, and press the [OK] button to confirm the selection, or press [ESC] to return to
the upper menu.
Selection Bo : User can move the highlight icon in the selection bo by using the [◄] and [►] button, and
press [OK] to confirm the selection. Multiple items are allowed to be selected together at once by left clicking
the mouse.
Sub menu list: User can move the highlight icon to the sub menu required by using the [◄] and [►] button,
or roll the mouse to select directly. Only one item can be selected here.
Edition Bo : When in edition bo , user can type in numbers directly by pressing the number buttons. Press
[DEL] to delete the character before the cursor and press [OK] or [ESC] button to e it.
Sub screen button: Press it to pop up the sub screen. When in sub screen, select [CONFIRM] to save the
configuration and return to the upper menu. Press [ESC] or select [CANCEL] to return to the upper menu
without being saved.
Use [◄], [►] to move the highlight icon to any of the selection bo es. Press [OK] button to switch to another
select status. User [▲], [▼] to specify the sub menu value where sub menu selections e ist.
E it: User can click the button on the upper right corner, or single right click the mouse, or press [ESC]
button to enter into the Save & E it screen. You can select e it directly or e it after being saved.
NOTE: There are two different ways to take effect: take effect instantly or take effect after being saved.
Please refer to the navigation for details.
7
Chapter Four: Operations
This chapter mainly describes the main system operations of the DVR. Please refer to the following contents
for details.
1 Turn on
Start Up
The power LED will be lit up after powering on correctly. Please refer to 2.6 Rear Panel Connection for
details of connection method. Press [Power on/off] to start up the device. The preview screen will appear.
After pressing the [ESC] button of the panel or remote, or right clicking the mouse, the login bo will appear.
Please select the proper user and type in the relevant password to log in.
NOTE: It takes about 60 seconds for the unit to start up. Please be patient.
NOTE: Modify the password by selecting <Tool Bar>→<System>→<System Setting>→<Password Setting>.
Set as indicated and the new password will take effect instantly.
NOTE: Default password for Admin is 111111. Default password for User is 111111. Admin password
can be restored to factory defaults by short-circuit “JP 1” on the main-board. After logging in by Admin, the
Admin can change the user's password. The system supports 8 users, and the Admin is the manager user
with all permissions, whose name cannot be deleted or changed. The Admin user can add and delete all
other users and permissions.
NOTE: The DVR will buzz and “NO Hard Disk” appears when running without a hard disk. User can choose
whether to buzz or not when using without a hard disk.
NOTE: The DVR can identify the display device automatically. When connected either to VGA or TV, the
menu will be on the specified screen automatically after start-up. When connecting VGA and TV
simultaneously, two images will be displayed on the screen, with it defaulting to VGA first. User can switch
by clicking in the tool bar.
SYSTEM SETTINGS
Language: Please enter <Tool Bar>→<System>→<System Setting>→<Language> to set the language.
VGA Resolution: Please enter <Tool Bar>→<System>→<System Setting>→<VGA Resolution> to set the
VGA resolution and refresh rate. It supports 800 600@60Hz, 1024 768@60Hz, 1280 1024@60Hz,
1440 900@60Hz currently. Please select relevant values according to the parameters of your setup.
Time Format: Please enter <Tool Bar>→<System>→<System Setting>→<Time Format> to set the time
format. 12 hour and 24 hour formats are supported.
Date/Time: Please enter <Tool Bar>→<System>→<System Setting>→<Time Setting> to set the date and
time.
Video Standard: Please enter <Tool Bar>→<System>→<System Setting>→<Video Standard> to set the
video standard. PAL, SECAM and NTSC are supported. Please set according to the parameters of the
camera.
NOTE: Please make sure the HDD is not recording when you set the system time, as it can cause an error
when playing back recorded video.
NOTE: “Language” and “Time” will take effect immediately. “Record Resolution” and “Video Standard” will
only take effect after being saved.
NOTE: When the resolution setting e ceeds the range of the display, please click [ESC][2][ESC] on the Front
Panel or remote controller within 3 seconds to reduce the resolution to 800 600@60Hz.
NOTE: Users can refer to the navigations on the bottom of the main screen to look for relevant guides.
Meanwhile, navigation info will display “Take effect instantly” / “Take effect after being saved”.
2 Preview
After starting up the system, the screen has a live view area and a tool bar. Right-click the mouse in
preview mode or press [OK] on the front panel, and the tool bar will appear. The system status column can
be dragged anywhere on the screen by mouse, and will be back in the default position ne t time the device is
restarted. The column can be hidden by right-clicking the mouse.
Videos, OSD of channel name, record time and alarm notifications will be displayed on screen.
8
1) Channel Status Display Area
Under preview mode, channel shows current input image and channel status information (video status and
mode, motion detection)
View Mode Switchin
When in 1/4/6/8/9/16 splits view mode, the tile with the highlighted green border is the currently selected one.
The user can use the mouse or press the direction buttons to switch to another tile. If the audio output
device is connected, the audio can be previewed together with video. The audio of the current channel can
be previewed besides in playback mode.
Users can select to display a particular channel by pressing the number buttons.
When in preview mode, user can enter into 1/4/6/8/9/16 splits view mode by pressing the button
directly, or vice versa.
NOTE: For 8 channel DVR, the view mode can be directly switched by tool bar. Please refer to 4.2.3 “Tool
Bar”.
Ima e Parameters Settin
Please enter <Tool Bar>→<System>→<Video>→<Colour Setting> to set brightness, contrast, hue and
saturation. It will take effect instantly.
NOTE: User can set image parameters of one channel one at a time, or for all channels at once by selecting
[ALL] in <Camera Channel>. It is similar to other screens when the user wants to set four channels together
at once: select [ALL] in <Channel>.
NOTE: In preview mode, brightness and contrast can be adjusted by the remote controller directly.
OSD Settin s
The OSD of channel name and system time is supported. Please enter <Tool Bar>→<System>→<Record
Setting>→<OSD Setting> to set. The channel name will be displayed on the left upper corner, and the
channel time will be displayed on the right corner of the screen.
Channel Status Display Area
The channel statuses include: “motion detection triggered recording” / “common recording” / “motion
recording” / “alarm triggered recording” / “e ternal alarm input” / “alarm output”.
Indication of “motion detection” / “common recording” / “alarm recording” will be displayed on the right upper
of screen. Details are as follows:
indicates “motion detection”. The settings of motion detection include sensitivity and area selection.
Please see “motion detection settings” for details.
Blue indicates “common recording”. Please see Record for details.
Green indicates “motion detection triggered recording”.
Red indicates “alarm triggered recording”.
Grey indicates “manual recording”.
Indication of “e ternal alarm input” / “alarm output” will be displayed on the system status column or tool bar.
Details are as follows.
: The 4/8 icons indicate the alarm input status. If alarm defence mode is set, the icon is , otherwise it
is . When alarm is triggered, the icon changes to red . E ternal alarm input can trigger multiple events
handling. Please see alarm settings for details.
: The 1/4 icons indicate alarm output. When alarm output is occurring, it changes to red .
System status bar
In preview mode, the system status bar will display the current system status, including: “E ternal alarm
input” / “Alarm output” / “Hard disk capacity” / “Number of Client connection” / “System Time”.
indicates the disk is OK. Number displayed indicates the capacity percentage of the disk remaining.
indicates “Hard disk error” or “No hard disk”.
indicates client connection. The number shows the client linking number.
indicates “no client connection”.
9
Tabla de contenidos
Otros manuales de Sistema de seguridad de Kogan
Manuales populares de Sistema de seguridad de otras marcas
EDM
EDM Solution 6+6 Wireless-AE Manual de usuario
Highway Safety Group
Highway Safety Group EA401 Manual de usuario
Siren
Siren LED GSM Manual de usuario
Detection Systems
Detection Systems 7090i Instrucciones de montaje
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Manual de usuario
Siemens
Siemens FDM273 Manual de usuario