Kodak Digital Science 9500 Instrucciones de funcionamiento
User’s
Maintenance
Guide
A-61092
Part No. 1E8133
Document Scanner 9500
A-61092 September 1999 5-1
5 Maintenance
Cleaning tasks To keep your scanner in good operating condition, the following tasks
should be performed:
•Cleaning the imaging guides (daily)
•Cleaning the feed and separator roller (semi-automatic feeder)
(daily)
•Cleaning the feeder module and separator roller (automatic feeder)
(daily)
•Cleaning the paper path (daily)
•Vacuuming inside the scanner (daily)
•Cleaning the exposure lamp housings (weekly)
•Cleaning the cabinet (weekly)
•Cleaning the air filter (monthly)
For additional maintenance and feeder adjustment information, see
Kodak publication A-61604. This publication is part of the Maintenance
and Feeder Adjustment procedure video; Catalog Number 828 5306.
Cleaning materials Materials needed to perform maintenance procedures are:
•A mild cleaning agent
•A quality lens cleaner
•A soft, clean, lint-free cloth
•A soft-bristled cleaning brush
•A vacuum cleaner
•Staticide Wipes
•Roller Cleaning Pads
•Paper Path Cleaner
IMPORTANT:
Do not use any unauthorized commercial cleaning
solvent in any of the cleaning procedures.
Replacement parts Consumable parts that can be replaced by the customer include:
•Air filter
•Exposure lamps
•Imaging guides
•Automatic Document Feeder Module
•Automatic Document Feeder Separator Roller
Instructions on how to replace these parts are included later in this
chapter.
5-2 A-61092 September 1999
Daily maintenance
procedures Maintenance procedures that should be performed daily include
cleaning the imaging guides, the feed and separator rollers, the paper
path and vacuuming inside the scanner.
Cleaning the imaging
guides To clean the imaging guides, follow the steps below:
IMPORTANT:
Do not use any abrasive materials when cleaning the
imaging guides. This includes abrasive cleansers,
commercial solvents, paper towels, or coarse cloths.
1. Open the right-side access door.
NOTE: The illustration below shows the rear view of the scanner.
Upper lamp
housing assembly
Upper imaging guide
Lower image guide
Lower lamp housing
assembly Right-side access door
Upper imaging guide
Lower imaging guide
2. Locate and grasp the end of the upper imaging guide. Carefully
slide the imaging guide out of its track.
3. Locate and grasp the end of the lower imaging guide. Carefully
slide the imaging guide out of its track.
A-61092 September 1999 5-3
4. Remove dust from the imaging guides, using a soft bristle brush.
5. Remove fingerprints or smudges from the imaging guides, wiping
both sides of each imaging guide with a clean, soft, lint-free cloth
slightly moistened with water or lens cleaner. Then, lightly wipe
both sides of each imaging guide with a dry cloth or an antistatic
wipe.
IMPORTANT:
Do not use cleaning pads on the imaging guides. Do
not use any abrasive materials when cleaning the
guides. This includes abrasive cleansers, commercial
solvents, paper towels, or course cloths.
6. Remove the upper lamp housing assembly.
7. Remove dust from the upper lamp housing assembly, using a soft
bristle brush.
8. Reinstall the upper lamp housing assembly.
Repeat Steps 6 through 8 for the lower lamp housing assembly.
IMPORTANT:
Use care when handling the imaging guides. Hold
the imaging guides by the green handles only.
9. Grasp and hold the lower imaging guide by the green handle and
carefully slide it back into place. Make sure the grooves fully
engage the track.
10. Grasp and hold the upper imaging guide by the green handle and
carefully slide it back into place. Make sure the grooves fully
engage the track.
NOTE: The imaging guides are not interchangeable. They can
only be inserted one way.
11. Close the right-side access door.
5-4 A-61092 September 1999
Cleaning the feed and
separator rollers (semi-
automatic feeder)
Clean the feed and separator rollers at least twice a day to prevent ink,
toner, and dust from collecting on the rollers and preventing documents
from separating.
1. Grasp the front cover and swing it open to the right.
Roller cover
Release lever
Feed roller
Separator roller
2. Push the roller cover release lever toward the back of the machine.
3. Grasp and rotate the roller cover toward the back of the machine,
exposing the feed and separator rollers.
Roller assembly
Feed roller
Separator roller
4. Hold the feed and separator rollers and scrub them with a roller
cleaning pad until all residue is removed from the roller ribs. Clean
the five small normal force rollers (below the feed roller — not
shown in this illustration) in the same manner.
5. Wipe the feed and separator rollers and the five normal force rollers
with a clean, dry, lint-free cloth to dry the rollers.
6. Rotate the roller assembly back into position.
7. Close the front cover.
A-61092 September 1999 5-5
Cleaning the feeder
module and separator
roller (automatic feeder)
Clean the feeder module and separator roller daily to prevent ink, toner,
and dust from collecting on the rollers and preventing documents from
separating.
Cleaning the feeder module and separator roller:
1. Open the front cover.
2. Push the roller cover release lever toward the back of the machine.
3. Grasp and rotate the roller cover toward the back of the machine,
exposing the feeder module and separator roller.
4. Remove the feeder module by pushing it to the right and lifting it out
of its position.
5. Clean both rollers of the feeder module.
6. Replace the feeder module, by aligning the pins and fitting it into
position.
Roller cover
release lever
Roller cover
Feeder
module
5-6 A-61092 September 1999
Cleaning the separator roller:
1. Open the front cover.
2. Push the roller cover release lever toward the back of the machine.
3. Grasp and rotate the roller cover toward the back of the machine,
exposing the feeder module and separator roller.
4. Lift and remove the separator roller cover plate.
5. Lift the separator roller out of the grooved brackets.
6. Clean the separator roller. Inspect the roller any areas where the
white foam is showing through the roller cover. If the roller shows
signs of wear, obtain and replace the separator roller.
7. Replace the separator roller by aligning the pins in the grooved
brackets.
8. Reinsert the separator roller cover plate.
9. Close the feeder cover.
10. Close the front door.
Roller cover
Feeder module
Roller cover
release lever
Separator roller
Grooved brackets
A-61092 September 1999 5-7
Cleaning the paper path NOTE: Before doing the following procedure, clean the machine
thoroughly and use the roller cleaning pads to clean the feed,
separator and normal force rollers — start with a clean
machine.
Use the Paper Path Cleaner to clean the paper path rollers. Periodically
feed a cleaning sheet with the gum side up through the machine in both
the portrait and landscape orientation.
The paper path should be cleaned twice a day. Before you clean the
paper path, be sure the feed and separator rollers and imaging guides
have been cleaned.
1. To ensure complete coverage of the transport and normal force
rollers, feed the cleaning sheet in the center, and to the left and
right of the feeder document guides.
2. Repeat the procedure until no further residue is picked up by the
cleaning sheet.
3. Using a clean Paper Path Cleaner sheet, repeat Step 1 to verify that
the rollers are clean.
4. Turn the gum side down, and repeat Steps 1 through 3.
NOTE: When the gum side is down, it may be necessary to hold
down the gap release lever to allow the Paper Path Cleaner
sheet to feed past the separator roller.
Regular use of Paper Path Cleaner sheets may result in fewer major
cleanings with the roller cleaning pads.
NOTE: If there are feeder errors after cleaning the feed and separator
rollers, refer to the section entitled “Adjusting the feed and
separator roller gap”, in Chapter 2.
Vacuuming inside the
scanner The sensors located under the horizontal plate in the feeder/horizontal
transport area and in the upper section of the lower roller housing
assembly, the exposure lamp housings, and the air filter should be
vacuumed or wiped down thoroughly with a clean, dry, soft, lint-free
cloth at least once a week.
Refer to the instructions and illustrations provided in the Chapter 7,
Troubleshooting,
to assist in accessing the sensor locations.
5-8 A-61092 September 1999
Cleaning the feeder/
horizontal transport area The sensors in the feeder/horizontal transport area are located under
the horizontal plate, behind the feed/separator rollers, near the reflector
strips.
1. Open the front cover.
2. Raise the horizontal plate.
3. Vacuum the area underneath the horizontal plate.
4. Remove the lower belt module.
5. Vacuum under the module and wipe with a clean, damp cloth.
6. Replace the lower belt module.
7. Lower the horizontal plate back into place.
8. Close the front cover.
Cleaning the lower roller
housing assembly area To clean the lower roller housing assembly area, follow the steps
below:
1. Open the top cover.
2. Open the right-side access door.
3. Remove the imaging guides (not shown in illustration).
IMPORTANT:
Use care when handling the imaging guides. Hold
the imaging guides by the green handles only.
Vertical baffle handle
Baffle plate
Lower roller
housing
assembly
Screen
Lower roller
housing assembly
4. Grasp the vertical baffle handle, push it in and turn it
counterclockwise until the baffle plate unlatches. Pull the baffle
plate down until it stops, this unlocks the lower roller housing
assembly.
A-61092 September 1999 5-9
5. Slide the lower roller housing assembly out of its housing and
vacuum inside the housing.
IMPORTANT:
Do not slide the lower roller housing assembly back
into place without first removing the imaging guides.
Failure to remove them first can cause misalignment
and/or damage to the machine.
6. Slide the lower roller housing assembly back into its original
position.
7. Replace the imaging guides.
8. Vacuum the screen located at the base of the transport system.
9. Raise the baffle plate and push it into its original position. Turn the
vertical baffle handle and latch it into place.
10. Close the right-side access door and top cover.
Otros manuales para Digital Science 9500
1
Tabla de contenidos
Otros manuales de Escáner de Kodak
Kodak
Kodak i1400 Series Manual de usuario
Kodak
Kodak I610 - Document Scanner Instrucciones de montaje
Kodak
Kodak i100 Series Manual de usuario
Kodak
Kodak i4200 Manual de usuario
Kodak
Kodak i4600 Manual
Kodak
Kodak 3520D - Digital Science Manual de usuario
Kodak
Kodak i2900 Manual de usuario
Kodak
Kodak HR 500 Manual
Kodak
Kodak I610 - Document Scanner Manual de usuario
Kodak
Kodak i30 Instrucciones de montaje
Kodak
Kodak A-61506 Manual de usuario
Kodak
Kodak SLIDE N SCAN Manual de usuario
Kodak
Kodak Truper 3210 Manual de usuario
Kodak
Kodak Scanmate i1120 Manual de usuario
Kodak
Kodak ScanMate i940 Manual de usuario
Kodak
Kodak I780 - Document Scanner Manual de usuario
Kodak
Kodak SCAN STATION 100 Manual de capacitación
Kodak
Kodak PS400 Series Manual de usuario
Kodak
Kodak Digital Science 9520 Manual de usuario
Kodak
Kodak I250 - Document Scanner Manual de usuario
