Kodak PIXPRO WPZ2 Manual de usuario

User Manual

DIGITAL CAMERA

KODAK PIXPRO WPZ2

Declaration of Conformity

Responsible Party: JK Imaging Ltd.

Address: JK Imaging Ltd., 17239 So. Main Street, Gardena, CA 90248 USA

Company website: kodakpixpro.com

INDUSTRY CANADA

This device complies with Canadian RSS210.

This device complies with Industry Canada license-exempt RSS standard (s).Operation is subject to the

following two conditions: (1) this device may not cause interference, and (2) this device must accept any

interference, including interference that may cause undesired operation of the device.

Radiation Exposure Statement:

This product complies with the Canadian portable RF exposure limit set forth for an uncontrolled

environment and is safe for intended operation as described in this manual. Additional RF exposure

reduction can be achieved if the product can be kept as far as possible from the user body or set the device

to lower output power if such function is available.

BEFORE YOU START

For Customers in Europe

This symbol [crossed-out wheel bin WEEE Annex IV] indicates separate collection of electrical

waste and electronic equipment in the European countries. Please do not throw the equipment into

domestic refuse. Please use the return and collection systems available in your country for proper,

safe disposal of this product.

“CE” mark indicates that this product complies with the European requirements for safety, health,

environment and customer protection. “CE” marked cameras are intended for sales in Europe.

Europe – EU Declaration of Conformity

This device complies with the essential requirements of the R&TTE Directive 2014/53/EU. The

following test methods have been applied in order to provepresumption of conformity with the

essential requirements of the R&TTE Directive 2014/53/EU:

- EN 609501: 2006+A11:2009 +A1:2010 +A12:2011

Safety of Information Technology Equipment

- EN 50566: 2013

Product standard to demonstrate compliance of radio frequency ields from handheld and body-

mounted wireless communication devices used by the general public (30 MHz — 6 GHz)

- EN 622092: 2010

Human exposure to radio frequency ields from handheld and bodymounted wireless communication

devices — Human models, instrumentation, and procedures

Part 2: Procedure to determine the speciic absorption rate (SAR) for wireless communication devices

used in close proximity to the human body (frequency range of 30 MHz to 6 GHz)

- EN 300 328 V1.8.1 : 2012

Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband Transmission systems;

Data transmission equipment operating in the 2.4 GHz ISM band and using spread spectrum

modulation techniques; Harmonized EN covering essential requirements under article 3.2 of the

R&TTE Directive.

- EN 301 4891 V1.9.2: 2011

Electromagnetic compatibility and Radio Spectrum Matters (ERM); Electro Magnetic Compatibility

(EMC) standard for radio equipment and services; Part 1: Common technical requirements.

- EN 301 48917 V2.2.1:2012

Electromagnetic compatibility and Radio spectrum Matters (ERM); Electro Magnetic Compatibility

(EMC) standard for radio equipment and services; Part 17: Speciic conditions for 2.4 GHz wideband

transmission systems and 5 GHz high performance RLAN equipment.

Manufacturer: Sintai Optical (Shenzhen) Co., Ltd

Address: Qiwei Ind Sec, 1st, 2nd,& 3RD Bldg, Lisonglang Village, Gongming Town, Bao’an

District, Shenzhen, Guangdong, China

Batteries: Please dispose of used batteries at designated collection centers.

Packaging: Please follow local regulations for the recycling of packaging.

For Customers in the U.S.A.

Federal Communication Commission Interference Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)

This device may not cause harmful interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment o and on, the user is encouraged to try to correct the interference

by one of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modiications not expressly approved by the party responsible for compliance

could void the user’s authority to operate this equipment.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Radiation Exposure Statement:

This product complies with the FCC portable RF exposure limit set forth for an uncontrolled environment

and is safe for intended operation as described in this manual. Additional RF exposure reduction can be

achieved if the product can be kept as far as possible from the user body or set the device to lower output

power if such function is available.

About this Manual

Thank you for purchasing this KODAK PIXPRO Digital Camera. Please read this manual carefully and keep it

in a safe place for future reference.

JK Imaging Ltd. reserves all rights of this document. No part of this published manual may be

reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or

computer language, in any form, by any means, without the prior written permission of JK Imaging Ltd.

All trademarks mentioned in this manual are used for identiication purposes only and are properties of

their respective owners.

This manual provides you with instructions on how to use your new KODAK PIXPRO Digital Camera. Every

eort has been made to ensure that the contents of this manual are accurate; however JK Imaging Ltd.

reserves the right to make changes without notice.

Throughout this manual, the following symbols are used to help you locate information quickly and

easily:

Indicates useful information.

The following symbols may be used throughout this manual to facilitate your understanding of how to

operate the camera:

[Item properties]: The optional properties in the camera interface are indicated by the [ ] symbol.

If there is dust, sand or other foreign materials on

the waterproof rubber of the battery cover and its

contact surface, please wipe it with a clean, dry

and lint free cloth as soon as possible.

Before using the product underwater, make sure

that there is no damage to or foreign debris on

the waterproof rubber gasket. Then close the

battery cover tightly to ensure the waterproof

capability of the product.

Waterproof rubber with scratches and cracks

will allow water to penetrate into the product.

Contact customer service immediately

for maintenance with replacement of new

waterproof rubber.

SAFETY NOTES

Waterproof / Dustproof / Shockproof

JIS / IEC waterproof grade 8 (IPX8).

JIS / IEC dustproof grade 6 (IP6X).

Height for shockproof rating is 2m (6.6 feet).

Waterprooing Notes:

Do not use the product below 15 meters (49.2

feet) underwater. The product can remain

waterproof for one hour at the depth of 15m

(49.2 feet).

Do not use this product in a geothermal spring

or in water at a temperature greater than 40 °C

(104°F).

Please do not open the battery cover

underwater.

If water accidentally comes in contact with the

product, please do not open the battery cover.

Turn the product o, and dry it with a clean, dry

and lint free cloth. Then open the battery cover,

and remove the battery and the memory card.

When opening the battery cover, if there are

water drops on the contact surface between

the inside of the battery cover and the body,

please dry the water drops.

After using the product in water or near sand,

mud or other foreign materials, please rinse it

with clean water (close the battery cover before

cleaning). After cleaning, dry the product with a

clean, dry and lint free cloth.

Waterproof Rubber

Safety Notes for this Camera

Do not drop the camera or allow it to hit solid

objects.

Do not attempt to disassemble or repair the

camera.

Do not use or store the camera in dusty places

or on a beach to help prevent dust or sand from

entering the camera, causing possible damage.

Do not use or store the camera in a hot

environment or in direct sunlight.

Do not use or store the camera near powerful

magnetic ields, for example near a magnet or

transformer.

Avoid touching the lens of the camera.

Do not expose the camera to direct sunlight for

a long period of time.

To prevent the camera from being damaged by

moisture, do not use or store the camera in very

humid environments, such as in rain or near

bodies of water.

If water accidentally comes in contact with

the interior of the camera, turn the camera

o immediately, remove the battery and the

memory card and dry it completely within 24

hours.

When you take the camera from a cold

environment to a warmer environment,

condensation may occur. Please wait for a

reasonable period of time before you turn the

camera on.

Make sure the camera is turned o before you

remove the battery and memory card.

When you clean the body of the camera, do

not use abrasive, alcohol-based or organic

cleansers or solvents.

Use a professional lens cleaning cloth and

appropriate cleaner to wipe and clean the lens.

Download your photos and remove the memory

card when you are going to store the camera

for long periods of time.

If this camera is not in use for a long period of

time, please keep it in a dry and clean storage

location.

Our company will not pay compensation for any

failure of playback of pictures or videos caused

by improper operation.

Safety Notes for Battery

Please use a battery that is the same type as the

one included.

Please use the included USB cable and AC

adapter to charge the battery inside the

camera.

If battery luid leaks inside the camera, contact

our customer service department immediately.

If battery luid leaks onto your skin, rinse your

skin with clean water and seek immediate

medical attention.

Disposal of used batteries should be carried

out in accordance with your local (national or

regional) regulations.

To prevent the battery from being damaged,

do not drop the battery or allow it to hit solid

objects or to be scratched by foreign objects.

Do not let the battery come in contact with

metal objects (including coins) to avoid short

circuiting, discharging, excessive heat or

possible leakage.

Do not attempt to disassemble the battery.

Do not expose the battery to water. Always keep

the battery contacts dry.

Do not heat the battery or throw it into a ire to

avoid a possible explosion.

Do not store the battery in a hot environment or in

direct sunlight.

If the battery overheats during charging or use,

stop charging or stop use immediately. Turn o

the product, remove the battery carefully and

wait until it cools down.

When the camera is stored for a long period of

time, remove the battery and keep it in a safe,

dry place that is not accessible to infants and

children.

In colder environments, the performance of the

battery could be noticeably reduced.

When you install the battery, align the battery

markings according to the positive and

negative markings inside the camera battery

compartment. Never force the battery into the

battery compartment.

Safety Notes for Memory Cards

The memory card referred to in this user manual

is a microSD card/microSDHC card that is Class

4 or higher and no larger than 32GB.

We highly suggest buying only well-known,

name brand memory cards to ensure peak

performance and reliability.

Format the memory card using the camera

before you use it to store photo or video iles or

when you insert a new memory card.

Do not drop the memory card or allow it to hit

solid objects to avoid damaging it.

Do not attempt to disassemble or repair the

memory card.

Do not expose the memory card to water.

Always keep it dry.

Do not remove the memory card when

the camera is turned on. Otherwise, the

memory card and photo/video iles could be

permanently damaged.

Do not directly edit the data on the memory

card. Copy the data to your computer before

you edit iles.

When the camera is stored for long periods

of time, be sure to download your photos and

remove the memory card. Store the memory

card in a dry environment.

Do not modify the name of the iles or folders

of the memory card using your computer.

Modifying the ile names may cause the iles to

not be recognized on the camera or a possible

permanent error may occur.

A photo taken with the camera will be stored in

the folder that is automatically generated on the

memory card. Do not store photos that are not

taken using this camera in these folders as the

pictures cannot be recognized during playback.

When you insert the memory card, make sure

the notch of the card matches the markings on

the top of the camera card slot.

Otros manuales para PIXPRO WPZ2

Tabla de contenidos

Otros manuales de Cámara digital de Kodak

Kodak

Kodak DC240 Instrucciones de montaje

Kodak

Kodak EASYSHARE C183 Manual de servicio

Kodak

Kodak Z712 - EASYSHARE IS Digital Camera Manual de usuario

Kodak

Kodak DCS Pro Back Plus Manual de usuario

Kodak

Kodak PIXPRO AZS250 Manual de usuario

Kodak

Kodak EASYSHARE M5350 Manual de servicio

Kodak

Kodak Pro 14n - DCS-14N 13.89MP Professional Digital SLR... Manual de usuario

Kodak

Kodak CX7300 - EASYSHARE Digital Camera Manual de usuario

Kodak

Kodak DCS 720x Manual

Kodak

Kodak C610 - EXTENDED GUIDE Manual de usuario

Kodak

Kodak Z612 - EasyShare 6.1 MP Digital Camera Manual de usuario

Kodak

Kodak RODSV50 Manual de usuario

Kodak

Kodak Z980 - EASYSHARE Digital Camera Manual de servicio

Kodak

Kodak Digital Science DC40 Manual de usuario

Kodak

Kodak PIXPRO WPZ2 Manual de usuario

Kodak

Kodak Z915 - EASYSHARE Digital Camera Manual de usuario

Kodak

Kodak PIXPRO AZ251 Manual de usuario

Kodak

Kodak PIXPRO AZ521 Manual de usuario

Kodak

Kodak EASYSHARE TOUCH M577 Manual de usuario

Kodak

Kodak EASYSHARE Z812 IS Manual de usuario

Kodak

Kodak C743 - EASYSHARE Digital Camera Manual de usuario

Kodak

Kodak ZD710 - EASYSHARE Digital Camera Manual de usuario

Kodak

Kodak EASYSHARE Z5120 Manual de usuario

Kodak

Kodak Pixpro AZ651 Manual de usuario

Manuales populares de Cámara digital de otras marcas

Mercury

Mercury 350K Manual de usuario

Pentax

Pentax Optio LS 465 Manual de usuario

Sanyo

Sanyo VPC-S1085 Manual de usuario

GE SMART A1255 Manual de usuario

Point Grey

Point Grey Gazelle Manual de usuario

Nikon

Nikon COOLPIX A Manual de usuario

Pentax

Pentax P-5 Manual de usuario

BlazeVideo

BlazeVideo A280 Manual de usuario

Sony

Sony MCA-20 Manual de usuario

Sony

Sony Alpha DSLR-A290 Manual de usuario

ATIK Cameras

ATIK Cameras One Manual de usuario

CohuHD Costar

CohuHD Costar 3930 Series Manual de usuario

Leica

Leica M10-R Manual de usuario

FujiFilm

FujiFilm FinePix A700 Manual de usuario

Lorex

Lorex LNZ81P25 Series Manual de usuario

GE J1470S Manual de usuario

Sony

Sony A6700 Guía del usuario

Canon

Canon EOS ELAN7 Manual de usuario