Kodak UC101 Manual de usuario
GB
FR
ES
IT
PT
FI
ET
DA
Quick Start
Guide
KODAK Car Charger UC101
02
HOW TO ATTACH MAGNET PLATE SHEET
Note: The magnet plate sheet must be used correctly to
charge and mount phone stably. Follow the below
instuctions, otherwise wireless charging will not work.
Be sure to aix the included magnet plate sheet
perfectly to the phone case with the double sided tape,
otherwise it will move and interfere or stop the wireless
charging process.
Do not use any other magnet plates with this wireless
charger.
Center of Coil
Wireless Coil
image 1
1 - Find the center of the wireless coil in the phone as shown in
image 1.
Generally most phones, it is located in the center of the
phone.
2 - Place magnet plate sheet into the phone case and mount
onto the holder to check for the correct mounting and
charging position before aixing double sided tape on to
the phone case.
03
The magnet plate sheet center point must be aligned
perfectly to both coil centers of holder and phone.
Refer to image 2.
3 - Peel o the protection sheet from the double sided tape
on the magnet plate sheet (image 3).
4 - Firmly aix magnet plate sheet to phone case.
5 - When mounting phone onto holder, be sure that the
metal sheets perfectly align with the 4 magnets in the
holder as shown in image 4 to achieve enough magnetic
strength.
image 2 image 3
Caution: It is recommended phone case with
thickness of 2mm or less be used for optimal
mounting and charging.
If the magnet plate or any foreign objects come into
contact with either coil, the charger will not work
correctly due to interference.
04
image 4 image 5
6 - Connect the holder and the car charger with provided
USB cable as shown in image 5.
7 - Check the phone and LED indicator on the holder to make
sure phone is charging correctly.
The recommended capacity of a car charger is more
than 1.5A.
05
LED INDICATOR
Fully Charged
Wireless Charging Error
White and Red LED Blinking
Over and Low Voltage
Over and Low Currency
Over Heat
Foreign Object Detection
Over Distance
Power On White LED
(Turns o after 3sec)
Wireless Charging Red LED
LED changes from
Red to White (Only Samsung Galaxy)
CHARGER SPECIFICATIONS
Max Current
Input Voltage
Input Connector Type
1.5A
Micro USB
5W
4.75 - 5.25 V
Power Provided
110 - 250 KHz
Frequency
Wireless Coil A11
Over and Low Voltage
Protection
Workable Temperature
Over and Low Currency
Over Heat
Foreign Object Detection
Over Distance
-10~30℃
06
4 - Press the suction plate firmly against attaching position
and press the lever to lock.
5 - Check the strength of the suction.
1 - Select a location to install the holder and clean the area
where suction base will be placed.
2 - Unlock the suction lever.
3 - Peel out the gel pad protection clear sheet.
Refer to image 6.
SUCTION BASE INSTALLATION
The optional use of the included suction plate is for unsmooth
surfaces to be used in conjunction with sticky gel suction base.
1 - Clean area where suction plate is to be placed.
2 - Peel o the protection sheet from the double sided suction
plate and fix to chosen area. (Then follow steps 2-5 of the
HOW TO USE SUCTION PLATE
image 6
Suction Base
Sticky Gel Pad
Protection Clear Sheet
07
above suction base installation by placing the sticky gel suction
base on to the suction plate).
The sticky gel pad can be cleaned with water to maintain
stickiness. After washing, please check the stickiness has
recovered after a short period of time.
CAUTION
MAINTENANCE OF GEL PAD
1 - It is advised wireless charging be done in cooler
environments.
In a hot environment, the charging speed will decrease or
charging will stop automatically with overheat protection.
Recommeded charging environment from 5°- 25°
2 - It is normal for the phone to get hotter whilst wireless
charging compared to cable charging.
3 - The phone will not charge normally with a phone case
thicker than 2mm.
4 - Wireless pad must not come into contact with metal,
magnetic or hot objects.
5 - Periodically check the strength of the suction base.
6 - Do not install the holder where it will obstruct the driving
view.
7 - Do not operate phone and holder while driving.
8 - Be careful not to operate charger near implantable medical
devices.
C.
suction plate
08
WARRANTY CARD
Copyright 2018, Car Parts Design Trading Co. Ltd.
www.carpadesign.net/kodak
Car Parts Design Trading Co., Ltd.
21st Floor Tai Yau Building 181
Johnston Road Wanchai, Hong Kong
The Kodak trademark, logo and trade dress are used under license from Kodak.
The supplier guarantees Carpa Design
Other warranty
restrictions that are
not covered by it.
Information
SERVICES DESCRIPTION
Warranty period 24 months within the EU.
12 months outside the EU.
Location
Based Restrictions
The warranty only applies to the country
where the sale takes place.
Conditions The receipt must be attached to the
warranty claim.
The warranty of the products will be
communicated with the corresponding
warranty card in the box along with the
warranty conditions that can be downloaded
as a PDF file from the warranty technical
service website.
- Abnormal use of the product.
- Accidental damage.
- Aesthetic defects.
- Extreme weather conditions.
- The use of non-compatible and/or
non-original accessories.
- User data loss.
GB
FR
ES
IT
PT
FI
ET
DA
Guide de démarrage
rapide
KODAK Chargeur de voiture UC101
FIXATION DE LA PLAQUE MAGNÉTIQUE
Remarque: la plaque magnétique doit être utilisée
correctement pour garantir le maintien et le chargement
du téléphone dans une position stable. Le non-respect
des instructions ci-dessous peut compromettre le
chargement sans fil. Assurez-vous que la plaque
magnétique incluse est parfaitement alignée et fixée sur
la coque du téléphone à l’aide du ruban adhésif double
face. Dans le cas contraire, elle risque de bouger et de
perturber ou interrompre le chargement. N’utilisez pas
d’autre plaque magnétique que celle fournie avec ce
chargeur sans fil.
Centre de la bobine
Bobine sans fil
Image1
1 – Trouvez le centre de la bobine sans fil du téléphone (image1).
Sur la plupart des modèles, il se situe au centre du téléphone.
2 – Placez la plaque magnétique dans la coque du téléphone
et installez le téléphone sur le support pour vérifier qu’il est
correctement installé et peut charger. Puis, fixez la plaque
sur la coque du téléphone à l’aide de l’adhésif double face.
10
Tabla de contenidos
Idiomas:
Otros manuales de Accesorios para automóviles de Kodak
