Knightsbridge SN3P Manual de instrucciones

INSTALLATION & MAINTENANCE MANUAL

SN3P / SN4P

These instructions should be read carefully and retained after installation by the

end user for future reference and maintenance.

These instructions should be used to aid installation of the following products:

SN3P / SN4P

GENERAL INSTRUCTIONS

SAFETY

INSTALLATION

• This product must be installed in accordance with the latest edition of the IEE Wiring

Regulations (BS7671) and current Building Regulations. If in any doubt, consult a

qualiﬁed electrician

• Please isolate mains prior to installation or maintenance

• Please note the IP (Ingress Protection) rating of this product when deciding the location

for installation

• Do not overload this accessory or subject it to conditions outside its rating

• This product is for indoor use only

• This product is IP20 rated

• Provide power to the required point of installation

• Squeezing the tab on the top of the connector to pull the two halves apart (see Fig. 1)

INSTALLATION & MAINTENANCE MANUAL

These instructions should be read carefully and retained after installation by the end user for future reference

and maintenance.

These instructions should be used to aid installation of the following products:

SN3P / SN4P

SAFETY

•This product must be installed in accordance with the latest edition of the IEE Wiring Regulations

(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician

•Please isolate mains prior to installation or maintenance

•Please note the IP (Ingress Protection) rating of this product when deciding the location for installation

•Do not overload this accessory or subject it to conditions outside its rating

•This product is for indoor use only

•This product is IP20 rated

INSTALLATION

•Provide power to the required point of installation

•Squeezing the tab on the top of the connector to pull the two halves apart (see Fig. 1)

Fig. 1

•Squeeze the sides of each half together to remove the cover (see Fig. 2)

Fig. 2

•Ensuring correct polarity is observed, carefully wire the supply side of the connector as shown in Fig. 3

Fig. 3

•Connect the load side ensuring the correct polarity is observed (see Fig. 4)

INSTALLATION & MAINTENANCE MANUAL

These instructions should be read carefully and retained after installation by the end user for future reference

and maintenance.

These instructions should be used to aid installation of the following products:

SN3P / SN4P

SAFETY

•This product must be installed in accordance with the latest edition of the IEE Wiring Regulations

(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician

•Please isolate mains prior to installation or maintenance

•Please note the IP (Ingress Protection) rating of this product when deciding the location for installation

•Do not overload this accessory or subject it to conditions outside its rating

•This product is for indoor use only

•This product is IP20 rated

INSTALLATION

•Provide power to the required point of installation

•Squeezing the tab on the top of the connector to pull the two halves apart (see Fig. 1)

Fig. 1

•Squeeze the sides of each half together to remove the cover (see Fig. 2)

Fig. 2

•Ensuring correct polarity is observed, carefully wire the supply side of the connector as shown in Fig. 3

Fig. 3

•Connect the load side ensuring the correct polarity is observed (see Fig. 4)

• Squeeze the sides of each half together to remove the cover (see Fig. 2)

• Ensuring correct polarity is observed, carefully wire the supply side of the connector as

shown in Fig. 3

Fig. 1

Fig. 2

INSTALLATION & MAINTENANCE MANUAL

These instructions should be read carefully and retained after installation by the end user for future reference

and maintenance.

These instructions should be used to aid installation of the following products:

SN3P / SN4P

SAFETY

•This product must be installed in accordance with the latest edition of the IEE Wiring Regulations

(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician

•Please isolate mains prior to installation or maintenance

•Please note the IP (Ingress Protection) rating of this product when deciding the location for installation

•Do not overload this accessory or subject it to conditions outside its rating

•This product is for indoor use only

•This product is IP20 rated

INSTALLATION

•Provide power to the required point of installation

•Squeezing the tab on the top of the connector to pull the two halves apart (see Fig. 1)

Fig. 1

•Squeeze the sides of each half together to remove the cover (see Fig. 2)

Fig. 2

•Ensuring correct polarity is observed, carefully wire the supply side of the connector as shown in Fig. 3

Fig. 3

•Connect the load side ensuring the correct polarity is observed (see Fig. 4)

Fig. 4

•Check all electrical connections are secure with all exposed copper within the terminal and no loose

strands of cable

•Refit the covers ensuring that the cables are secured by the cord grip

•Push the two halves together until the tab clicks into place

•Switch on and check for correct operation

GENERAL

Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may damage the

product.

This product should be recycled in the correct manner when it reaches the end of its life. Check local authorities

for where facilities exist.

WARRANTY

This product has a warranty of 1 year from date of purchase. Failure to install this product in accordance with

the current edition of the IEE Wiring Regulations (BS7671), improper use, or removal of the batch code will

invalidate the warranty. If this product should fail within its warranty period, it should be returned to the place of

purchase for a free of charge replacement. ML Accessories does not accept responsibility for any installation

costs associated with the replacement product. Your statutory rights are not affected. ML Accessories reserve

the right to alter product specification without prior notice.

230V 50Hz, IP20, indoor only

DCxxx22_V1

• Connect the load side ensuring the correct polarity is observed (see Fig. 4)

• Check all electrical connections are secure with all exposed copper within the terminal and

no loose strands of cable

• Reﬁt the covers ensuring that the cables are secured by the cord grip

• Push the two halves together until the tab clicks into place

• Switch on and check for correct operation

Fig. 3

Fig. 4

GENERAL

WARRANTY

Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which

may damage the product.

This product should be recycled in the correct manner when it reaches the end of its life.

Check local authorities for where facilities exist.

This product has a warranty of 1 year from date of purchase. Failure to install this product

in accordance with the current edition of the IEE Wiring Regulations (BS7671), improper

use, or removal of the batch code will invalidate the warranty. If this product should fail

within its warranty period, it should be returned to the place of purchase for a free of

charge replacement. ML Accessories does not accept responsibility for any installation

costs associated with the replacement product. Your statutory rights are not affected. ML

Accessories reserve the right to alter product speciﬁcation without prior notice.

DCSEP22_V1

SUPPLIED BY:

(UK) MANUFACTURER ML ACCESSORIES LTD,

UNIT E CHILTERN PARK, BOSCOMBE ROAD,

DUNSTABLE LU5 4LT,

WWW.MLACCESSORIES.CO.UK

(EU) SLV LIGHTING GROUP,

DAIMLERSTRASSE 21-23,

52531 ÜBACH-PALENBERG, GERMANY

EMAIL: EPREL@GROUP.SLV.COM

MADE IN CHINA

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Equipo de iluminación de Knightsbridge

Knightsbridge

Knightsbridge 24DCIP60 Manual de instrucciones

Knightsbridge

Knightsbridge BL12ALEDEM Manual de instrucciones

Knightsbridge

Knightsbridge EMGUKIT1 Manual de instrucciones

Knightsbridge

Knightsbridge KIT4B Manual de instrucciones

Knightsbridge

Knightsbridge LEDM06 Series Manual de instrucciones

Knightsbridge

Knightsbridge EMPOWER2 Manual de instrucciones

Knightsbridge

Knightsbridge GDL2 Manual de instrucciones

Knightsbridge

Knightsbridge CPL6CT Manual de instrucciones

Knightsbridge

Knightsbridge TNXQUADSTW Manual de instrucciones

Knightsbridge

Knightsbridge BATC Series Manual de instrucciones

Knightsbridge

Knightsbridge LEDFIPRGBW Manual de instrucciones

Knightsbridge

Knightsbridge OS002 Manual de instrucciones

Knightsbridge

Knightsbridge TNXQUADEMW Manual de instrucciones

Knightsbridge

Knightsbridge EMSWING Manual de instrucciones

Knightsbridge

Knightsbridge TNXQUADMWSTW Manual de instrucciones

Knightsbridge

Knightsbridge EMPOWERST Manual de instrucciones

Knightsbridge

Knightsbridge BT14CTEM Manual de instrucciones

Knightsbridge

Knightsbridge EMXST Manual de instrucciones

Knightsbridge

Knightsbridge SHE P Series Manual de instrucciones

Knightsbridge

Knightsbridge EMPOWERST Manual de instrucciones

Knightsbridge

Knightsbridge 12DC40 Manual de instrucciones

Knightsbridge

Knightsbridge BATC Series Manual de instrucciones

Knightsbridge

Knightsbridge TNXQUADW Manual de instrucciones

Knightsbridge

Knightsbridge TRI Series Manual de instrucciones

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario