KMC Controls NetSensor KMD-1101 Instrucciones de funcionamiento originales

Installation & Operation Guide

KMD-1101/1121 NetSensor

893-019-01F

Introduction

This section provides a brief overview of the KMD-1101/1121 NetSensor. Review

this material before you attempt to install the controller.

Illustration 1 shows the major components and their locations.

Illustration 1. NetSensor Component1

LED Display

11TIMETIME

Main Control

Buttons

Flip Door PC Port

RJ–12 Connector

Secondary Button Group

(Under Flip Door)

SETPOINTSETPOINT

OVERRIDEOVERRIDE

ROOMROOMûûFF

O.A.O.A.ûûFF

NOTE: Actual label text will depend on

application and labels used.

3.280 (83.3)

0.875

2.750

4.500

Installation

This section provides important instructions and guidelines for installing the

KMD-1101/1121 NetSensors. These boards are designed for use with KMD-5500

and KMD-6000 series controllers.

Carefully review this information prior to attempting installation.

Installation

Note:

Preliminary wiring to each sensor location should be completed prior to actual

sensor installation. (This includes the installation of the appropriate mounting

base.) If wiring is not completed, finish that first. Mounting backplates are

available from KMC. (See the appropriate datasheet for accessories.)

To install the NetSensor unit:

1. Turn the Allen screws in the base of the Netsensor clockwise until they clear

the cover then swing the sensor away from the backplate to remove it.

2. Feed the RJ–12 cable through the mounting base.

3. Secure the mounting base to the backplate or the 2” x 4” outlet box with

the Allen screws toward the floor.

4. If the pig-tail leads are being used, connect them to the wires coming from

the wall mount as indicated in the site wiring diagram. Be sure to protect

bare wires with suitable insulating material.

5. Insert the RJ– 12 cable coming from the base into the NetSensor.

6. Place the top of the NetSensor over the top of the mounting base and swing

it down over the Allen screw brackets. Be careful not to pinch any wiring.

7. Back the Allen screws out of the brackets until they engage the NetSensor

cover and hold it in place.

Operation

Controls and Indicators

The following sections describe the controls and indicators found on the

NetSensor.

Display

The display contains four .375-inch, 7-segment LEDs that are visible across a

normal size office. The display can be programmed to remain on constantly, or to

turn off after a set time period. (Refer to the KMD Applications Manual for

programming instructions.)

Controls

The KMD-1101/1121 NetSensors include a total of nine pushbuttons; seven of

which are user programmable. The actual operation of the programmable but-

tons will depend on the program assigned to the device.

The remaining two buttons will adjust the value (up or down) if this function is

enabled in the programming. Values can be changed for all buttons (if pro-

grammed) except the #1 button as follows:

1. Press the button for the desired function.

2. Adjust the value up or down.

PC Port

The NetSensor is equipped with a PC Port. This port provides a RS–485 connec-

tion to the digital network that is accessible by a PC. The port is located beneath

the flip door on the side of the controller.

To use this port:

1. Open the flip door on the front of the controller.

2. Connect the keyed, flat end of the KMD-5624 NetSensor to PC cable to the

port on the NetSensor.

3. Connect the RJ–11 end of the cable to device that converts the RS–485

signal from the NetSensor into an RS–232 signal.

Note:

The KMD-5557 Computer Interface or the KMD-5559 CommTalk are suitable

for this purpose.

4. Connect a suitable cable (such as the KMD-5625) from the interface to the

computer’s serial port.

You should have normal access to the network provided the PC has the proper

software application installed and the serial port is configured properly.

Disclaimer

The material in this document is provided for information purposes only.

The contents and the product(s) described herein are subject to change

without notice. KMC Controls, Inc. makes no representations or warranties

with respect to this document. In no event shall KMC Controls, Inc. be liable

for any damages, direct or incidental, arising out of or related to the use of

this document.

Important Notices

No part of this publication may be reproduced, transmitted, transcribed,

stored in a retrieval system, or translated into any language in any form by

any means without the written permission of KMC Controls, Inc.Printed in

U.S.A.

Technical Support

If you have any questions about this technical document or need additional

details, please call KMC Controls technical services at 574-831-5250 or e-

mail us at [email protected].

KMC Controls

P.O. Box 497

19476 Industrial Drive

New Paris, IN 46553

U.S.A.

TEL: 574.831.5250

FAX: 574.831.5252

E-mail: [email protected]

893-019-01D

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Termostato de KMC Controls

KMC Controls

KMC Controls CTE-5202 Instrucciones de funcionamiento

KMC Controls

KMC Controls BAC-19 FlexStat Series Guía del usuario

KMC Controls

KMC Controls FlexStat Guía del usuario

KMC Controls

KMC Controls FlexStat BAC-10000 Series Manual de usuario

KMC Controls

KMC Controls FlexStat Manual de usuario

KMC Controls

KMC Controls CTE-1005 Manual de usuario

KMC Controls

KMC Controls CTE-5202 Guía del usuario

KMC Controls

KMC Controls CTC-4001 Manual de usuario

KMC Controls

KMC Controls FlexStat Manual de usuario

KMC Controls

KMC Controls FlexStat BACnet Manual de usuario

KMC Controls

KMC Controls CTC-1653 Manual de usuario

KMC Controls

KMC Controls CTC–5500 Series Manual de usuario

KMC Controls

KMC Controls FlexStat Manual de usuario

KMC Controls

KMC Controls CTE-5001 Manual de usuario

KMC Controls

KMC Controls FlexStat BACnet Manual de usuario

KMC Controls

KMC Controls CTE–5101 Manual de usuario

KMC Controls

KMC Controls BAC-1xx63 Series Manual de usuario

KMC Controls

KMC Controls CTE-5201 Instrucciones de funcionamiento

KMC Controls

KMC Controls FlexStat Manual de usuario

Manuales populares de Termostato de otras marcas

EWELLY

EWELLY EW-181 Manual de usuario

Prolon

Prolon T1100 Instrucciones de instalación

Computherm

Computherm Q20 Manual de usuario

Heatmiser

Heatmiser neoStat Manual de usuario

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manual de usuario

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manual de usuario

Saswell

Saswell SAS920XWHB-7-S-RF Guía

Aircalo

Aircalo TFP1-ET85P2 Manual de usuario

Honeywell

Honeywell CM721 Manual de usuario

Carrier

Carrier DEBONAIR 33CS Manual de usuario

Lennox

Lennox iHarmony Zone Thermostat Instrucciones de montaje

Gemtech

Gemtech GT7000 Manual de instrucciones

Rollei

Rollei Smartes 45000 Manual de usuario

Sinope

Sinope TH1300RF Manual de usuario

Honeywell

Honeywell RLV4305 Manual de usuario

Honeywell

Honeywell Prestige 2.0 THX9421 Manual de usuario

NuTone

NuTone NTBZ48 Instrucciones de funcionamiento originales

Stelpro

Stelpro MAESTRO ASMT402AD Manual de usuario