Kleinn RS-GM6 Manual de usuario

Installation Guide

RS-GM6

*For automatic transmission vehicles only

•This remote start will monitor the vehicle lock circuit and use the pulses generated by pressing Lock>Unlock>Lock on

your OEM remote to start the vehicle.

•This is a pre-wired "plug & play" kit. No wiring is required for basic installation.

•We have already loaded the correct firmware into the remote start module. You will need to pair the module to your

vehicle when the wiring is complete. Instructions are on page 4.

There are 6 basic steps to this remote start installation. We’re going

to address each of these:

Download and install Flash Link Manager software

Locate the BCM connectors under the dash (no disassembly required)

Plug the connectors in to the vehicle.

Pair the remote start to the vehicle.

Test the system and record your Service Number

Button it up!

Step 1: Download and install Flash Link Manager software

**The Flash Link Manager (FLM) software only works on a Windows computer and requires a USB port and an

internet connection. Enter the following link into your web browser, then download and install the software:

https://fortin.ca/en/support/flashlinkmanager.html

Next, open the software and log in with the following credentials:

email: [email protected]

password: Flash2020

Once the (FLM) software installed and open, then connect the Flash Link Lite (FLL) to the USB port of your Windows

computer. The (FLM) software will detect (FLL) and display a message that the module is not connected, this is normal. Do

not plug the remote starter into the (FLL) tool until you have completed the wiring and vehicle programming procedure at

step 3. Leave the computer and software in this state ready to plug the module in when the time comes, and proceed with

the wiring connections.

REV 01132021

You may view a high-resolution

color version of this guide online

at http://install.kleinn.com/RSGM6

or by scanning this QR code.

1| P a g e

Overview

Silverado 1500 2019

Suburban 2015-2019

Tahoe 2015-2019

CHEVROLET

Sierra 1500 2019

2018-2020Terrain

Yukon 2015-2019

GMC

Step 2: Locate BCM Connectors

Step 3: Wiring

3.1 PLUG-IN VEHICLE CONNECTIONS:

a. Unplug the Blue, Green and White connectors from the vehicle BCM, then insert each one in to the corresponding

female connector on the t-harness.

b. Insert the male Blue, Green and White connectors from the t-harness in to the BCM.

2| P a g e

The vehicle BCM is under the dash on the driver's side, to the

left of the brake and just above the foot rest. You will not

need to remove any panels to access it. It can be identified by

the 7 colored plugs, as shown here.

a. Valet/Kill Switch - There is a mini toggle switch supplied with your kit. Connecting one side of the switch to the

Blue wire from the 20-pin plug and the other side of the switch to ground will allow the toggle switch to serve as a

'kill' switch for the system. Putting the switch in the "ON" position (continuity between both side of the switch) will

disable the system.

3.2 OPTIONAL WIRE CONNECTIONS - from the loose wires attached to the 20-pin connector

System Wiring Overview

3| P a g e

Yellow

Purple

Purple/White

Green

White

Orange

Orange/Black

Dk.Blue

Red/Blue

Lt.Blue/Black

A10

Out A11A11

A11

Out A12A12

A12

In A13

A13

Brown/White Out A14

A14

Pink/Black Out A15

A15

A16A16

A16

A17

Green/Red A18

A18

White/Black A19

A19

Lt.Blue A20

A20

C3 Gray

C2C2

C2 Orange/Brown

D6 White/Red

D4 White/Green

In A2

In A3

Out A5

In A8

In A1

In A9

A9A9

In A7

A7A7

In A6

Out A4

A4A4

(+)Ignion

NOT USED

Start / Stop external control

Contrôle de démarrage/arrêt

externe

Hood pin

OVERRIDE SWITCH

Hood pin only required on vehicles not

equipped with a factory hood pin.

27 PIN MALE

T-HARNESS PLUG

FEMALE T-HARNESS PLUG

26 PIN MALE

T-HARNESS PLUG

FEMALE T-HARNESS PLUG

MALE VEHICLE WHITE PLUG

25 PIN MALE

T-HARNESS PLUG

FEMALE T-HARNESS PLUG

MALE VEHICLE GREEN PLUG

26 PIN WHITE CONN.

THAR-GM6

27 PIN BLUE 25 PIN GREEN

MALE VEHICLE BLUE PLUG

BCM Above Driver Kick Panel.

5 PIN CONN.

OPTIONAL RFKIT

RF KIT

CABLE INCLUDED WITH RF KIT

BLUE FEMALE

CONNNECTOR

EVO-ALL

6 PIN RED CONN.

4| Pag e

RELEASE

xx55

Release the programming

button when the LED is

YELLOW.

If the LED is not solid YELLOW

disconnect the 4-Pin connector

(Data-Link) and go back to step

Insert the white 20-pin, red 6-pin and white 5-pin connectors.

FLASH

CONTINUED NEXT PAGE

OFF

Press and release the programming

button five times (5x).



The YELLOW LED will alternate

between 5x flashes and a pause.

Wait until the YELLOW LED turns ON.

FLASH

1Press and hold the

programming button:

Connect the 4-PIN Data-link

harness (Black connector).

The Blue, Red, Yellow and

Blue & Red LEDs will

alternatively illuminate.

xx11

HOLD

LED may differ depending on the module casing.

L’apparence des DELS peuvent différer selon le

boîtier du module.

Step 4: Programming/Pairing

Unplug all the connectors from the EVO module, then follow the steps below.

First generation

Place

OEM remotes

the OEM remotes in the

1 génération de clé:

Placez la télécommandes

icule dans

nt de la clé.

Remove the battery from the

OEM remote.

Second generation

remotes:

de la

télécommande d'origine.

Remove the battery from the

OEM remotes.

Place the OEM remotes in to the

center console.

Open the driver door.

START

PRESS

HOLD

RELEASE

START

IGNITIONOFF START

OFF

The RED LED will turn ON.

The YELLOW LED will turn

OFF.

Press the foot-brake pedal.

Press the Push-to-Start

button until the engine

start.

Release the foot-brake pedal.

NʼEST

5| P a g e

OFF

Press the Push-to-Start

button until the engine

turn OFF.

Press the Push-to-Start

button until the engine

turn OFF.

Close and open the

driver door.

The BLUE LED will turn ON.

The BLUE LED will turn OFF.

The RED LED will turn OFF.

The YELLOW LED will flash

rapidly

The BLUE LED will turn ON.

OFF

The BLUE LED will flash

rapidly

The BLUE LED will flash

slowly

OFF

PRESS

HOLD

RELEASE

OFF

PRESS

HOLD

RELEASE

START

PRESS

HOLD

RELEASE

START

Press the foot-brake pedal.

Press the Push-to-Start

button until the engine

start.

Release the foot-brake pedal.

IGNITION ON IGNITION OFF

OFF

FLASH

START

ACCESSORY OFF

FLASH

RAPIDLY

FLASH

RAPIDLY FLASH

SLOWLY

EVO-ALL

Disconnect all the connectors - do the

Data-Link (4-pin) connector last.

Use the tool:

FLASH LINK UPDATER

FLASH LINK UPDATER* FLASH LINK MANAGER*

SOFTWARE

Microsoft Windows

Computer with

Internet connection*

AFTER DCRYPTOR PROGRAMMING IS COMPLETED

Go back to the vehicle and reconnect the 4-Pin (Data-Link)

connector. The re-connect the white 20-pin, red 6-pin and

white 5-pin connectors.

EVO-ALL

DCRYPTOR PROGRAMMING EXPLAINED

DCRYPTOR writes the digital code from your key in to the EVO

module. It cannot be done in advance - it must be done after

wiring is completed.

Bring the remote starter module to your computer and plug it

into the supplied four-pin cable from the Flashlink Updater). For

a video on how to do these steps visit: www.kleinn.com/

flashlink

1. The software will detect you plugging it in and will automatically load the current settings.

2. Select your vehicle. Click the three bars at the top of the Red bar on the upper left corner of the screen. Select

your make, year, model, key type and then click load settings. Do not change any other dropdowns or any options -

we have already done these settings for you.

6| P a g e

4. Wait while the updater reads data from the remote starter. Once it is done it will update the remote starter

and you will need to wait again. You will see a status bar at the bottom of the screen. When it gets to 100%,

the Dcryptor process is complete.

5. You can now unplug the remote starter module and plug it back into the connectors in your vehicle. Make sure

to plug in the power connector first and then the rest of the plugs afterward. Do not hold the program button

down when you plug the connectors back in.

7| P a g e

3. Click the Dcryptor tab. Then click on the Send Data button.

8 | P a g e

Step 5: Test the System

If you have any installation questions or problems, call for tech support

520.579.1531

1. Press "Lock>UNLOCK>Lock" on your OEM remote control. You will see the Blue light on the remote start module

every time you press the Lock or Unlock buttons. Each press should be about 1 second apart. The vehicles ignition/

accessory circuits will turn on after a few seconds. Another few seconds later the starter motor will engage.

2. Step on the brake pedal to stop the engine.

•EVO-ALL Remote Start Data Module

•THAR-GM6 T-Harness

•Toggle Switch

•Pin Switch (not needed for most vehicles)

Step 7: Close it Up

Now gather up all of your wiring and neatly bundle it together using zip ties or electrical tape. Find a secure place to put

the remote start module and use zip ties to secure it. Make sure that the remote start wires are not near any

moving parts on the steering wheel, pedals or emergency brake! Re-Install any panels that were removed to

gain access to key switch in reverse order they were removed. Be careful not to pinch any wires. ENJOY!

Parts List

Step 6: Record your service number

Your EVO-ALL module has a unique service number. Before closing up

the installation, record that. In the event Kleinn tech support needs to

troubleshoot your system, they may need your service number to look up

the current status of your module.

001A07 ___________________

Remote start

the vehicle.

START

All doors must

be closed. Press the Unlock button of the

remote car starter.

UNLOCK

Enter the vehicle with the

Intelligent Access Key.

The vehicle can now be

put in to gear and

driven.

OFF

NOTE:

If the vehicle is not unlocked the module will shut down the remote-

starter and the vehicle as soon as any door is opened.

Tabla de contenidos

Otros manuales de Accesorios para automóviles de Kleinn

Kleinn

Kleinn GMHD20-230 Manual de usuario

Kleinn

Kleinn RAMHDOBA-6450 Manual de usuario

Kleinn

Kleinn JEEPKIT-1 Manual de usuario

Kleinn

Kleinn GMHD20-734 Manual de usuario

Kleinn

Kleinn GMHD20-OBA Manual de usuario

Kleinn

Kleinn JEEPKIT-99 Manual de usuario

Kleinn

Kleinn RZR1000-KIT Manual de usuario

Kleinn

Kleinn CANX3-KIT Manual de usuario

Manuales populares de Accesorios para automóviles de otras marcas

James Baroud

James Baroud Odyssey Manual de usuario

Motorola

Motorola i50sx Manual de usuario

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manual de usuario

Feniex

Feniex T3 Manual de usuario

Renault

Renault 77 11 423 180 Manual de usuario

Kia

Kia E8300-4D000 Manual de usuario

Brink

Brink 756843 Manual de usuario

Whispbar

Whispbar K085W Manual de usuario

v.link

v.link CI-VL2-PC-HSD Manual de usuario

Viking

Viking Stack-Rack Guía de configuración rápida

Aries

Aries 203015 Manual de usuario

Choetech

Choetech AT0005 Manual de usuario

ZZ2

ZZ2 ZZAIR-PRO Manual de usuario

Holman

Holman 4A80L Manual de usuario

Thule

Thule 2075 Manual de usuario

Motorola

Motorola T325 Manual de usuario

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guía de instalación

DV8

DV8 FBJL-02 Manual de usuario