Klein Tools CL800A Manual de usuario

INSTRUCTIONMANUAL

600A AC/DC Auto-Ranging

Digital Clamp Meter

TrueRMS

Measurement

Technology

• NON-CONTACT

VOLTAGE TESTER

• LOW IMPEDANCE

• DATA & RANGE HOLD

• AUDIBLE CONTINUITY

• DIODE TEST

• CAPACITANCE &

FREQUENCY

1000V

60M

600A

ENGLISH

日本語 pg. 33

한국어 pg. 17

IP40

-26° –

538° C

4007177

CL800A

GENERAL SPECIFICATIONS

Klein Tools CL800A is an automatically ranging true root mean square

(TRMS) digital clamp-meter that measures AC/DC current via the

clamp, measures AC/DC voltage, resistance, continuity, frequency,

capacitance, and tests diodes via test-leads, and temperature via a

thermocouple probe. It also features a Low Impedance (LoZ) mode

for identifying and eliminating ghost or stray voltages.

• Operating Altitude: 2000m

• Relative Humidity: <80% non-condensing

• Operating Temp: 0°to 40°C

• Storage Temp: -10°to 60°C

• Accuracy: Values stated at 18° to 28°C

• Temp Coefcient: 0.1 x (Quoted Accuracy) per °C above

28°C or below 18°C, corrections are required when ambient

working temp is outside of Accuracy Temp range

• Dimensions: 231 x 97 x 39 mm

• Weight: 354 g including batteries

• Calibration: Accurate for one year

• Standards: Conforms to: UL STD 61010-1, 61010-2-032,

61010-2-033.

Certified to: CSA STD C22.2 # 61010-1,

61010-2-032, 61010-2-033.

IEC EN 61010-1, 61010-2-032,

61010-2-033, 61326-1.

• Pollution degree: 2

• Accuracy: ± (% of reading + # of least significant digits)

• Drop Protection: 2m

• Safety Rating: CAT IV 600V, CAT III 1000V, Class 2,

Double insulation

CAT III: Measurement category III is applicable to test and

measuring circuits connected to the distribution part of the

building’s low-voltage MAINS installation.

CAT IV: Measurement category IV is applicable to test and

measuring circuits connected at the source of the building’s

low-voltage MAINS installation.

• Electromagnetic Environment: IEC EN 61326-1. This

equipment meets requirements for use in basic and controlled

electromagnetic environments like residential properties,

business premises, and light-industrial locations.

Specifications subject to change.

ENGLISH

ELECTRICAL SPECIFICATIONS

Function Range Resolution Accuracy (50/60 Hz)

AC Voltage

(V AC)

6.000V 1mV ±(1.5% + 5 digits)

60.00V 10mV ±(1.2% + 5 digits)

600.0V 100mV

1000V 1V ±(1.5% + 5 digits)

DC Voltage

(V DC)

600mV 0.1mV ±(1.0% + 8 digits)

6.000V 1mV

±(1.0% + 3 digits)60.00V 10mV

600.0V 100mV

1000V 1V ±(1.2% + 3 digits)

Input Impedance: 10MΩ Frequency Range: 50 to 400Hz

Maximum Input: 1000V AC RMS or 1000V DC

AC Current

(A AC)

60.00A 10mA ±(2.0% + 8 digits)

600.0A 100mA ±(2.0% + 5 digits)

DC Current

(A DC)

60.00A 10mA ±(2.0% + 8 digits)

600.0A 100mA ±(2.0% + 5 digits)

Frequency Range: 50 to 60Hz

Function Range Resolution Accuracy

Resistance

600.0Ω 0.1Ω

±(1.5% + 5 digits)

6.000KΩ 1Ω

60.00kΩ 10Ω

600.0kΩ 100Ω

6.000MΩ 1kΩ

60.00MΩ 10kΩ ±(2.0% + 10 digits)

Maximum Input: 600V AC RMS or 600V DC

Capacitance

60.00nF 0.010nF ±(5.0% + 35 digits)

600.0nF 0.1nF

±(3.0% + 5 digits)6.000µF 0.001µF

60.00µF 0.01µF

600.0µF 0.1µF ±(5.0% + 5 digits)

6000µF 1µF

Maximum Input: 600V AC RMS or 600V DC

Temperature

(Fahrenheit)

-14°to 32°F

0.1 to 1

°F

±(2.0% + 9

°F

)

33° to 752°F

±(1.0% + 5.4

°F

)

753° to 1000°F

±(2.0% + 9

°F

)

Temperature

(Celsius)

-26° to 0°C

0.1 to 1

°C

±(2.0% + 5

°C

)

1° to 400°C

±(1.0% + 3

°C

)

401° to 538°C

±(2.0% + 5

°C

)

ELECTRICAL SPECIFICATIONS

FREQUENCY (AUTO-RANGING)

9.999Hz 0.001Hz

±(1.0% + 5 digits)

99.99Hz 0.01Hz

999.9Hz 0.1Hz

9.999kHz 1Hz

99.99kHz 10Hz

500.00kHz 100Hz

Sensitivity: >8V RMS

Maximum Input: 600V DC or 600V AC RMS

DUTY CYCLE

1% to 99.9%

0.1% ±(1.2% + 2 digits)

Pulse width: 0.1 – 100ms

Frequency width: 5Hz to 10kHz

Sensitivity: >8V RMS

Maximum Input: 600V DC or 600V AC RMS

OTHER MEASUREMENT APPLICATIONS

Maximum Input: 600V AC RMS or 600V DC

• Diode Test: Max. 1.5mA, open circuit voltage ~3.0V DC

• Continuity Check: Audible signal <50Ω, test current <0.35mA

• Sampling Frequency: 3 samples per second

• Low Impedence (Low Z): Input impedence >3kΩ

Max input 600V RMS

• Auto Power off: After ~30 minutes of inactivity

• Overload:

"OL" indicated on display, overload protection

1000V in Voltage setting, 600V RMS in all other settings

• Polarity: "-" on display indicates negative polarity

• Display: 3-5/6 digit, 6000 Count LCD

ENGLISH

WARNINGS

To ensure safe operation and service of the meter, follow these

instructions. Failure to observe these warnings can result in

severe injury or death.

• Before each use verify meter operation by measuring a known

voltage or current.

• Never use the meter on a circuit with voltages that exceed the

category based rating of this meter.

• Do not use the meter during electrical storms or in wet weather.

• Do not use the meter or test leads if they appear to be damaged.

• Use only with CAT IV rated test leads.

WARNINGS

• Ensure meter leads are fully seated, and keep fingers away from

the metal probe contacts when making measurements.

• Do not open the meter to replace batteries while the probes are

connected.

• Use caution when working with voltages above 25V AC RMS or

60V DC. Such voltages pose a shock hazard.

• To avoid false readings that can lead to electrical shock, replace

batteries when a low battery indicator appears.

• Do not attempt to measure resistance or continuity on a live

circuit.

• Always adhere to local and national safety codes. Use personal

protective equipment to prevent shock and arc blast injury where

hazardous live conductors are exposed.

SYMBOLS ON METER

AC/DC

Resistance (in Ohms) Audible Continuity

Double Insulated Class II Ground

Diode Capacitance

Frequency

Duty-cycle

Temperature (Fahrenheit / Celsius)

Low Impedance

V Voltage (Volts) A Amperage (Amps)

Warning or Caution

To ensure safe operation and service of this meter, follow all

warnings and instructions detailed in this manual.

Risk of Electrical Shock

Improper use of this meter can lead to risk of electrical shock. Follow

all warnings and instructions detailed in this manual.

Risk of Electrical Shock

Application around and removal from UNINSULATED HAZARDOUS

LIVE conductors is permitted.

SYMBOLS ON LCD

AC Measurement

DC Measurement

Negative Reading Data Hold

Auto Ranging MAX Maximum Value Hold

MIN Minimum Value Hold Low Battery

Auto Power Off Audible Continuity

Diode Test

kilo (value x 10

)

Mega (value x 10

)

mili (value x 10

-3

)

micro (value x 10

-6

)

nano (value x 10

-9

)

Ohms

Volts

Amps

Farads

Frequency (Hertz)

Duty Cycle

Degrees (Fahrenheit)

Degrees (Celsius)

ENGLISH

FEATURE DETAILS

1. 6000 count LCD display 8. "MAX/MIN" button

2. Function selector switch 9.

"SEL" (select) button

3. Clamp 10.

Clamp trigger (press to open clamp)

4. "COM" jack 11. Arrow markings

5. "VΩ" jack 12. N

on-Contact Voltage Testing Button

6. Data Hold / Backlight /

Worklight button

13. Test lead holder for test probe

14.

Non-Contact Voltage Testing Sensor

7. "RANGE" button 15.

Polarity markings (for DC current)

16.

Worklight

(back of meter)

NOTE: There are no user-serviceable parts inside meter.

FUNCTION BUTTONS

ON/OFF

To power ON the meter, rotate the Function Selector switch

from

the OFF setting to any measurement setting. To power OFF the meter,

rotate the Function Selector switch

to the OFF setting. By default,

the meter will automatically power OFF after 30 minutes of inactivity.

If the meter automatically powers OFF while in a measurement

setting, rotate Function Selector switch

to any other setting

(excluding the OFF setting) to power ON the meter. To deactivate

the power OFF functionality press and hold the "SEL" button

before powering ON from the OFF setting. When auto power OFF

is deactivated, the Auto Power Off icon will not be visible in the

display.

"SEL" (SELECT) BUTTON (FOR SECONDARY FUNCTIONS)

The "SEL" button

activates the secondary function for each

application accessible by the function selector switch

. For current,

voltage, and low impedance it toggles between AC and DC, for the

other functions it switches between °F and °C, between Hz and %

Duty-Cycle, and between Continuity, Resistance, and Diode-Test. The

default function for each application is printed on the meter in white;

the secondary function or functions for each setting is printed on the

meter in orange.

DATA HOLD

Press the Data Hold / Backlight / Worklight button

to hold the

measurement on the display. Press again to release the display to

return to live measuring.

BACKLIGHT & WORKLIGHT

Press and hold the Data Hold / Backlight / Worklight button

for

more than one second to turn ON the backlight and worklight

simultaneously. The backlight and worklight will both automatically

power OFF after 3 minutes of inactivity.

RANGE

The meter defaults to auto-ranging mode . This mode

automatically determines the most appropriate measurement range

for the testing that is being conducted. To manually force the meter to

measure in a different range, use the Range button

1. Press the "RANGE" button

to manually select measurement

range ( is deactivated on the LCD). Repeatedly press the

"RANGE" button

to cycle through the available ranges, stopping

once the desired range is reached.

2. To return to auto-ranging mode, press and hold the "RANGE"

button

for more than one second ( is reactivated).

ENGLISH

FUNCTION BUTTONS

MAX/MIN

When the "MAX/MIN" button

is pressed, the meter keeps track

of the Maximum and Minimum values and the difference between

the Maximum and Minimum values as the meter continues to take

samples.

1. When measuring, press "MAX/MIN" button

to toggle between

the Maximum value (MAX) and the Minimum value (MIN). If a

new Maximum or Minimum occurs, the display will update with

the new value.

2. Press "MAX/MIN" button

for more than one second to return to

normal measuring mode.

NON-CONTACT VOLTAGE TESTING

Press the NCV button

to test for AC voltage using the integrated

non-contact voltage meter. Approach the conductor under test

leading with the sensing antenna

. The meter delivers visual

warning signals when AC voltage is detected.

TEST LEAD HOLDER

When working with test leads, one test probe may be mounted in the

test lead holder

to facilitate natural two-handed operation with the

clamp in one hand and a single test probe in the other.

OPERATING INSTRUCTIONS

CONNECTING TEST LEADS

Do not test if leads are improperly seated. Results could cause

intermittent display readings. To ensure proper connection, firmly

press leads into the input jack completely.

TESTING IN CAT III / CAT IV MEASUREMENT LOCATIONS

Ensure the test lead shield is pressed firmly in place. Failure to use

the CATIII / CATIV shield increases arc-flash risk.

TESTING IN CAT II MEASUREMENT LOCATIONS

CAT III / CAT IV shields may be removed for CAT II locations. This

will allow testing on recessed conductors such as standard wall

outlets. Take care not to lose the shields.

5/32"

(4 mm)

.7" (18 mm)

INCORRECT

CORRECT

ENGLISH

OPERATING INSTRUCTIONS

AC/DC CURRENT (LESS THAN 600A)

AC Current is measured by pressing the clamp trigger

to open

the clamp

and placing it around a current-carrying wire. When

measuring, care should be taken to ensure that the clamp

completely closed with trigger

fully released, and that the wire

passes perpendicularly through the center of the clamp

in line

with the arrow markings

To measure current:

1. Rotate the Function Selector switch

to the AC/DC current A

setting.

NOTE: The meter defaults to AC measurement. Press the "SEL"

button

to toggle between AC and DC modes. The AC or DC icon

on the LCD indicates which mode is selected.

2. Place clamp

around wire. When measuring DC current, align the

polarity markings

on the clamp with the polarity of the wire to

avoid negative readings. The current measurement will be shown in

the display. The meter will auto-range to display the measurement in

the most appropriate range.

Disconnect test leads when measuring with the clamp.

NOTE: If non-zero values are displayed prior to measuring in DC

current mode, an offset correction is required. With meter in DC

current mode, press and hold the "SEL" button

to activate the

DC current ZERO function. Subsequent DC current measurements

automatically subtract the offset correction for improved accuracy.

WIRE

Tabla de contenidos

Idiomas:

Otros manuales de Instrumento de medición de Klein Tools

Klein Tools

Klein Tools IR3000 Manual de usuario

Klein Tools

Klein Tools CL360 Manual de usuario

Klein Tools

Klein Tools CL700 Manual de usuario

Klein Tools

Klein Tools CL440 Manual de usuario

Klein Tools

Klein Tools CL200 Manual de usuario

Klein Tools

Klein Tools VDV501-089 Manual de usuario

Klein Tools

Klein Tools 935DAA Manual de usuario

Klein Tools

Klein Tools CL380 Manual de usuario

Klein Tools

Klein Tools CL2200 Manual de usuario

Klein Tools

Klein Tools CL2200 Manual de usuario

Klein Tools

Klein Tools CL900 Manual de usuario

Klein Tools

Klein Tools NCVT-1XTKIT Manual de usuario

Klein Tools

Klein Tools 93LDM100C Manual de usuario

Klein Tools

Klein Tools CL210 Manual de usuario

Klein Tools

Klein Tools MM1300 Manual de usuario

Klein Tools

Klein Tools 93LDM100C Manual de usuario

Klein Tools

Klein Tools ET100 Manual de usuario

Klein Tools

Klein Tools RT390 Manual de usuario

Klein Tools

Klein Tools MM1300 Manual de usuario

Klein Tools

Klein Tools CL150 Manual de usuario

Klein Tools

Klein Tools VDV512-110 Manual de usuario

Klein Tools

Klein Tools CL450 Manual de usuario

Klein Tools

Klein Tools ET110 Manual de usuario

Klein Tools

Klein Tools CL3200 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario