KitchenAid KCCC151 Manual de usuario

MODELS: KUCC151 and KCCC151

9871628B

For questions about features, operation/performance, parts accessories or service, call: 1-800-422-1230

In Canada, call for assistance: 1-800-461-5681, for installation and service call:1-800-807-6777 or visit our website at...

www.kitchenaid.com or www.kitchenaid.com/canada

COMPACTORS

Table of Contents............2

TABLE OF

CONTENTS

Compactor Safety ..........................................................3

Electrical Requirements ................................................4

How Your Compactor Works ........................................4

Parts and Features..........................................................5

Installing Your Compactor ............................................6

Unpacking Your Compactor..........................................6

Space Requirements ....................................................6

Freestanding and

Undercounter Installation ..................7

Adjusting the Toe Plate..................................................9

Changing the Decorative Panel ....................................9

Using Your Compactor ................................................10

Using the Charcoal Air Filter........................................10

Starting Your Compactor ............................................11

Using Solid (Locked) Cycle ........................................11

Removing a Filled Bag ................................................12

Installing a New Bag....................................................12

Caring for Your Compactor..........................................13

Changing the Charcoal Air Filter ................................13

Cleaning Your Compactor ..........................................13

Troubleshooting ............................................................14

Assistance or Service ..................................................15

Warranty ........................................................................16

You can be killed or seriously injured if you don't

immediately follow instructions.

You can be killed or seriously injured if you don't

follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you

what can happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all

safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or

“WARNING.” These words mean:

COMPACTOR SAFETY

IMPORTANT SAFETY INSTRUCTIONS

WARNING:When using an electrical appliance, basic precautions should always be followed, including the

following:

Read all instructions before using the compactor.

Close supervision is necessary when used by or

near children. Do not allow to be used as a toy, or

to run unattended at any time. Lock Key Switch

when not in use and store key out of reach of

children.

Do not touch moving parts.

Do not operate with a damaged cord set, plug,

motor, or after damage in any manner. Have the

compactor examined, repaired or adjusted by an

authorized serviceperson.

Use only for intended use as described in this

manual. Do not use other than manufacturer's

recommended attachments.

Do not take apart the compactor. Incorrect

reassembly can cause electric shock when

subsequently used.

Handle a loaded trash bag with care. Sharp objects

can pierce the bag and cause injury. Do not

overload trash bag with heavy material such as

glass.

■This compactor is intended for household use only.

Do not compact toxic or volatile flammable material

such as oily rags and insect sprays. Do not compact

lighted cigarettes, cigars, or other hot or burning

items. Do not overload the compactor.

■

SAVE THESE INSTRUCTIONS

Electrical Requirements

This compactor must be grounded while in use to reduce

the risk of electric shock.The compactor is equipped with

a three-conductor cord and three-prong grounding-type

plug to fit the proper grounding-type receptacle.The green

(or green and yellow) conductor in the cord is the ground-

ing wire. Never connect the green (or green and yellow)

wire to a live terminal.The outlet should be properly

installed and grounded in accordance with the National

Electrical Code and local codes and ordinances. No

adapter should be used with this appliance.

Recommended Grounding Method

This compactor is for use on a single phase, 115-volt, 60

Hz, AC only 15 or 20 ampere fused and properly ground-

ed circuit and is equipped with a grounding plug as shown

below.Time delay fuse or circuit breaker is recommended.

It is recommended that a separate circuit serving only this

appliance be provided. In the event of an electrical short

circuit, grounding reduces the risk of electric shock by

providing an escape wire for the electric current. Do not

modify the plug attached to the compactor; use only with

a grounded receptacle.

wWARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Failure to follow these instructions can result in

death, fire, or electrical shock.

How Your

Compactor Works

The compacting ram is the part of the compactor which

compresses the trash.The compacting ram does not go

to the bottom of the drawer.You will not see compacting

of trash the first few times you load the compactor.

NOTE: The compactor drawer should be about 1/2 full

before the compactor can begin to compress the load.

You may hear a noise when glass breaks. Strong glass

bottles may not break at all.

The trash in a full compactor bag will be about 1⁄4the size

of its original bulk.

Load bulky trash, bottles, and cans in the center of the

drawer. Bottles or cans not placed in the center may

become caught between the ram and the drawer.The

drawer monitor switch senses a “misload”and causes the

ram to return to the “up”position without compacting.

PARTS AND FEATURES

1. Key-knob start switch

2. Charcoal air filter switch

3. Drawer handle

4. Model and serial number

label

5. Wraparound panel

6. Touch-toe bar drawer opener

7. Compact switch

8. Activated charcoal air filter

9. Drawer monitor switch

10. Bag retainer buttons

11. Lever-action lock

START

OFF

AIRFILTER

SOLID

(LOCKED)

NORMAL

(ADDTRASH)

COMPACT

INSTALLING

YOUR

COMPACTOR

leveling legs

4. Place the other two corner posts on the floor to the

side of the compactor. Grasp the sides of the com-

pactor cabinet and put compactor on its side on top of

the corner posts. Remove the shipping base from the

bottom of compactor.

3. Place two corner posts from carton on floor near com-

pactor. Open compactor drawer and remove any shipping

materials or other items shipped in the drawer. Do not

remove the compactor bag (if installed). Grasp the handle

and raise the front of drawer until it clears the drawer

stops. Grasp sides of drawer and lift drawer out of

compactor. Place the drawer on the two corner posts.

IMPORTANT:

Installer: Leave Use and Care Guide with the homeowner.

Homeowner: Keep Use and Care Guide for future reference

and for local electrical inspector’s use, if required.

wWARNING

Excessive Weight Hazard

Use two or more people to move and install

compactor.

Failure to do so can result in back or other

injury.

Space Requirements

Check the location where your compactor will be

installed.The cabinet opening should be square.You

should be able to fully open the compactor drawer. Six

inches (15.2 cm) of clearance is needed on the right side

of compactor drawer to be able to remove compactor bag.

Allow 23 inches (58.4 cm) in front of the compactor to

remove drawer.

341⁄8"

(86.7 cm)

24"

(61 cm)

15"

(38.1 cm)

The overall look of your compactor may vary.

Product dimensions

Unpacking Your

Compactor

IMPORTANT:

• Do not grasp console to move compactor.

• Begin in the room where the compactor will be

located.

1. Remove compactor from shipping carton. Remove

all protective packaging materials such as tape and

shipping pads. Remove waxy residue caused by pro-

tective shipping material with a mild solution of liquid

household cleaner and water.

2. Check that power supply cord is attached to the cord

clip on the rear of the compactor.

cord

clip

1. Use pliers to lower leveling legs away from cabinet.

Place level inside on the floor of the cabinet. Check that

the compactor is level from front to back and side to

side. Adjust the leveling legs until the compactor is

level.

Freestanding installation:

2. Move the compactor close to its final position. Plug

the power supply cord into a 3-prong grounded outlet.

3. Carefully move compactor into its final position.

Check that compactor is still level. Repeat step 1

if necessary.

4. Grasp sides of compactor drawer and place bottom

of drawer into tracks. Lift at the handle so drawer will

go over drawer stops. Close drawer. Check if drawer

opens freely. If the toe plate rubs against floor, see

“Adjusting the Toe Plate”for further instructions.

Freestanding and Undercounter Installation

NOTE: Proper installation is your responsibility. Make sure

you have everything necessary for correct installation. It is

the personal responsibility and obligation of the customer

to contact a qualified installer to assure that electrical

installation meets all national and local codes and ordi-

nances.

Tools and materials needed for installation:

Level

Pliers

Scissors

Phillips screwdriver

Flat-Blade screwdriver

Utility knife

Measuring tape

5⁄16" (8 mm)-Box-end wrench

Gloves

IMPORTANT:

• Do not grasp console to move compactor.

• Slide compactor onto cardboard or hardboard

before moving compactor across floor to prevent

damaging floor covering.

• Do not allow the rear frame of the compactor to

touch the floor covering when lifting or moving com-

pactor.

18" min.

(45.7 cm)

24" min.

(61 cm)

Grounded

electrical outlet

must be

3" (7.6 cm) min.

from either side

wall.

6" (15.2 cm)

clearance to the

nearest vertical

wall on the right

side of compactor

is needed to

remove bag.

23" (58.4 cm) clearance in

front of the compactor is

needed to fully open or

remove compactor drawer.

151⁄4" min.

(38.7 cm)

341⁄4" min.

(87 cm)

Cutout dimensions

Clearance dimensions

Undercounter installation:

NOTE: Installation hardware is not provided with full

cabinet models.

1. Measure the height of your cabinet opening.The top of

the compactor should be at least 1⁄8" (3 mm) from the

top of the cabinet opening.

The rear wheels are preset for a cabinet opening

height of 341⁄4" (87 cm) (Position “A”).

To adjust for other cabinet opening heights, loosen

screw just enough to clear stud from hole in position

“A”. Move the rear wheel and stud to position “B”or “C”

as needed for your cabinet opening measurement:

Position B: 341⁄4" to 347⁄16" (87 to 87.5 cm)

Position C: 347⁄16" to 345⁄8" (87.5 to 88 cm)

Tighten screw. Repeat for other rear wheel.

cabinet

locating stud

self-tapping

screw (pivot)

wheel

bracket

assembly

Countertop mounting

mounting

screw

retaining

bracket

6. Grasp sides of compactor drawer and place bottom

of drawer into tracks. Lift at the handle so drawer will go

over drawer stops. Close drawer. Check if drawer opens

freely. If the toe plate rubs against floor, see “Adjusting

the Toe Plate”for further instructions.

Cabinet-front mounting

mounting

screw

retaining

bracket

mounting

clip

2. Use pliers to lower leveling legs away from cabinet.

Adjust legs so there will be a 1⁄8" (3 mm) to 1⁄4" (6.4 mm)

space between the top of the compactor and the top of

the cabinet opening. Stand the compactor upright.

3. For model with cabinet, remove the plastic plugs from the

compactor cabinet top.

4. Determine if you want the compactor frame or drawer

front flush with the cabinet front.

Using the two #8 -18 x 5⁄16" (8 mm) screws, install the

retaining brackets to cabinet top as needed:

If the compactor frame is to be flush with the cabinet

front, place retaining bracket screws through “A”.

If the compactor drawer front is to be flush with the

cabinet front, place retaining bracket screws through “C”.

If the compactor is to be midway between “A” and

“C”, place retaining bracket screws through “B”.

5. Carefully lift the front slightly and roll compactor into

the cabinet opening.

retaining

bracket

countertop

Using the two #8 -18 x 1⁄2" (12 mm) screws, fasten the

retaining brackets to the underside of the countertop

with the mounting screws.

If brackets cannot be attached to the underside of

countertop, attach mounting clips to brackets. Fasten

compactor to cabinet front with mounting screws

through mounting clips.

Changing the

Decorative Panel

2313⁄16"

(60.5 cm)

145⁄8"

(37.2 cm)

Raised panel: The outer section of panel must be 7⁄32"

(5.6 mm) thick to fit into trim. Raised panel dimensions as

shown above.

Custom-made panel dimensions

Adjusting theToe Plate

If the toe plate rubs the floor covering, the toe plate

clearance may be changed as follows:

1. Mark on each side of the toe plate the amount of toe

plate that rubs the floor covering.

2. Remove the drawer from the unit. (See step 3 in the

“Unpacking Your Compactor”section.)

3. Use a ruler and a pencil or chalk to draw a line

between the marks on each side of toe plate.

4. Use scissors or utility knife to cut toe plate along line.

5. Replace drawer. If toe plate still rubs floor covering,

repeat steps 1-4.

Flat panel: A 7⁄32" (5.6 mm) thick panel is required.This is

the same thickness as a standard 1⁄4" plywood or paneling.

Trim for decorative panel

Order trim for installation of a custom-made panel through

your KitchenAid dealer or by calling the KitchenAid

Consumer Assistance Center at 1-800-422-1230. In

Canada, call 1-800-807-6777.

Trim for custom-made panels available are:

Part No. 9871381 (Brushed stainless steel)

Part No. 9871382 (White)

Part No. 9871383 (Black)

Part No. 9871384 (Almond)

Part No. 9871600 (Biscuit)

7⁄32"

(5.6 mm) 11⁄4"

(32 mm)

5⁄16"

(8 mm)

both sides 5⁄16"

(8 mm)

outer section

of panel

raised

panel or

decorative

trim

145⁄8"

(37.2 cm)

2313⁄16"

(60.5 cm)

USING YOUR

COMPACTOR

Open the drawer

Lift and pull the handle or press the drawer opener to

open the drawer.

wWARNING

Explosion Hazard

Do not compact any container, aerosol cans, or

cloths which might contain insecticide, hair

spray, engine starting fluid, paints, liquids,

thinners, or any other poisonous or explosive

products.

Doing so can result in death, explosion, or fire.

wWARNING

Cut Hazard

Do not push items down into compactor with

hands or feet.

Doing so can result in cuts.

Put in the trash

NOTE: You will not see compacting of trash the first

few times you load the compactor. The compactor

drawer should be about 1/2 full before the compactor

can begin to compress the load.

1. Wrap or cover wet or messy trash.

2. Load bottles or cans on their sides in the center of the

drawer.

3. Do not load bottles in an upright position in drawer as

shown here.

4. Do not compact items that may develop offensive odors

such as raw meat, fish, grapefruit rinds, disposable dia-

pers, or personal hygiene items.

Close the drawer

Push drawer in until it stops.

Using the Charcoal Air Filter

The fan-powered Charcoal Air Filter absorbs and mini-

mizes odor.The degree of odor in the compactor

depends on the type of trash placed in it.The length of

time before the filter needs to be replaced varies with the

type of trash compacted. Under normal use the filter

should be replaced once or twice per year.

OFF

AIR FILTER

Indicator

To use the filter

1. Set the Charcoal Air Filter switch to ON. The Air Filter

indicator lights up.The fan creates air movement in the

compactor for odor removal.

NOTE: The Charcoal Air Filter works even when the

Key-Knob is in the OFF position.

2. Set the Charcoal Air Filter switch to OFF to turn off the

fan.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Compactador de basura de KitchenAid

KitchenAid

KitchenAid Architect Series II W10242569A Manual de usuario

KitchenAid

KitchenAid KUCS181T Manual de usuario

KitchenAid

KitchenAid KUCS03FTSS - 15" Trash Compactor Instrucciones de uso

KitchenAid

KitchenAid 9871915B Manual de usuario

KitchenAid

KitchenAid 4KUCS181T Manual de usuario

KitchenAid

KitchenAid KCC-151 Manual de usuario

KitchenAid

KitchenAid KUCP02IR Manual de usuario

KitchenAid

KitchenAid Integrated Compactor 9871915A Manual de usuario

KitchenAid

KitchenAid KFCK03IT Manual de usuario

KitchenAid

KitchenAid 4KUCS181T Manual de usuario

KitchenAid

KitchenAid KFCK03ITWH1 Guía de inicio rápido

KitchenAid

KitchenAid KCS-200 Manual de usuario

KitchenAid

KitchenAid 9872215B Manual de usuario

KitchenAid

KitchenAid KUCK03ITBL0 Manual de usuario

KitchenAid

KitchenAid KUCC151 Manual de usuario

KitchenAid

KitchenAid KUCS03FTPA0 Manual de usuario

KitchenAid

KitchenAid KUCC151JSS0 Manual de usuario

KitchenAid

KitchenAid KUCS03CTSS0 Manual de usuario

KitchenAid

KitchenAid KUCS03CTWH0 Manual de usuario

KitchenAid

KitchenAid 9871780C Manual de usuario

KitchenAid

KitchenAid KUCV151MSS0 Manual de usuario

KitchenAid

KitchenAid KUCS03FSSS0 Manual de usuario

KitchenAid

KitchenAid compactor Manual de usuario

KitchenAid

KitchenAid KFCK03ITWH0 Manual de usuario

Manuales populares de Compactador de basura de otras marcas

NuTone

NuTone 1050 Manual de usuario

Rousseau

Rousseau R1C-SE19S Manual de usuario

Kenmore

Kenmore 665.1361 Series Manual de usuario

Newstripe

Newstripe Pack-Master Air Manual de usuario

Whirlpool

Whirlpool GX900QPLQ - 15" Trash Compactor Manual de usuario

Vestil

Vestil FM-T-DUMP Manual de usuario

GE GCG1700P Manual

Euro Shatal

Euro Shatal RP4014-50 Manual de usuario

third coast equipment

third coast equipment SP3410 Manual de usuario

Cucine Oggi

Cucine Oggi EKKO CUBE 40 9000 Manual de usuario

GE GCG1700II Manual de usuario

Viking

Viking Designer Series Manual de usuario

GE GCG1500RBB Manual

Centro

Centro 85-1066-6 (A01001 Guía rápida

Whirlpool

Whirlpool 9872208 Manual de usuario

Jenn-Air

Jenn-Air TC607X2 Manual de usuario

Displays2go

Displays2go “THANK YOU” DUAL Manual de usuario

GE Monogram ZCG3500DSS Manual de usuario