Kimo FrigoPack EC FU+/12 Manual de usuario
FS 4.7 www.frigokimo.com
0. FrigoPack®EC FU+/12 Connections
Terminal designations of
FrigoPack®FU+/12
Warning: This is an abbreviated and customized version with recommendations for a rst setup of this product.
Please refer to the document "Planning Guide FrigoPack®EC FU+/12“ for detailed information.
FrigoPack®EC FU+/12 Quick-Start Guide
Refrigeration Inverters with external
signal input (0...+10 V / 4...20 mA)
FrigoSoft 4.7
- 1 -
OK
„Zurück“- Taste
● Auswahl eine Ebene zurück
● Bedienerebene durch mehrmaliges Drücken erreichbar
● Bricht Eingabevorgang ab
„OK“- Taste
● Auswahl eine Ebene vorwärts
● Wechsel in das Parametereingabefeld
● Bestätigung der Eingabe
„Grüne“- Taste
Dauerhaft grünes Licht
● Signalisiert, dass Verdichter läuft
● Blinkt zusammen mit „Rot“-Taste: Frequenzumrichter
bendet sich im Kongurationsmodus
FS 4.7 www.frigokimo.com
Ensure that all recommendations for compliance to mounting, electrical safety, EMC and UL regulations have
been adhered to.
1. Basic information on rst set-up
1.1 Recommendations
•It is important to ensure that an interlocked contactor is tted between the Refrigeration Inverter and the
compressor if a parallel bypass connection is used.
•In particular ensure that two isolated contacts of a relay are connected to the Safe-Torque-Off inputs of
FrigoPack®FU+ Refrigeration Inverter: STO-A (Terminal X10:1) / STO-B (Terminal X10.3).
• Remove start command (cable to terminal X13:2)
• Connect main power supply
1.2 Keypad functionality
1.3 Menus - Selection of user level for rst set-up
To start commissioning, the user level TECHNICIAN must be enabled. Please follow the steps shown below.
Press key "Back" several times to access the menu "View Level".
Password for user level TECHNICIAN: 8670. The level is then activated for 10 minutes.
- 2 -
OK
OK OKOK
PASSWORD:
8670
Back Back
Start screen Menu levels
User level
Key "Back"
● Navigates to previous level
● Press multiple times to enter Operator Menu
● Aborts the edit mode
Key "OK"
● Displays the next menu level
● Changes to parameter entry mode
● Accepts value entered
"Green" key
Green light on
● Compressor running
● When flashing with "Red" key: Frequency Inverter
in Configuration Mode
Key "Red"
● Resets any trip
Red light on
● Compressor stopped
● When flashing with "Green" key: Frequency Inverter
in Configuration Mode
Keys "Left" and "Right"
● Displays previous menu level
● Selects the digit to be changed
Keys "Up" and "Down"
● Moves up or down through selected menu level
● Increments / decrements the value of the displayed
parameter by "1"
www.frigokimo.com
The setting-up of this inverter can be done without SD memory card, as usually only 3 parameters are to be
set: Maximum compressor current (parameter 61) as well as maximum and minimum motor frequencies
(parameters 62 and 64). You may nd these parameters in the menu COMPRESSOR SETUP.
2. First set-up
Caution: When setting the value of parameter 61, keys "Green" and "Red" are ashing permanently
(conguration mode). Conrm your setting with key "OK" and then press "Red" shortly in order
to leave the conguration mode!
KIMO RHVAC Controls GmbH | Hüttendorfer Weg 60 | D - 90768 Fürth, Germany
01117.144-472/08
Connect start command (cable to terminal X13:2) to start the system!
Please contact our
applications team for any
questions in planning or
commissioning under
or
tel +49 (0) 9131 – 934570
Otros manuales de Inversor de Kimo
