Kidde P4010LDCS-WCA Manual de usuario

WIRELESS

Photoelectric Smoke Alarm

with Voice and Wireless Interconnect

User Guide

Model P4010DCS-WCA

Model P4010LDCS-WCA

(Safety Light)

WIRELESS INTERCONNECT:

You do NOT need a home wi-fi

system to use these units. Multiple

wireless units create their own

independent wireless alarm

network.

10YEAR BATTERY

WIRELESS INTERCONNECT

VOICE ALARM

SMOKE ALARM

P/N: 0314-7202- 01

Thank You for Purchasing this Kidde Alarm

These models are powered by a non-replaceable, long life sealed lithium battery system, and include

Hush®Control to temporarily silence nuisance alarms. They are capable of Wireless Interconnect.

READ SECTION 9: Activation and Wireless Alarm Network, before powering the units. You do

NOT need a home wi-fi system to use these units. Multiple wireless units create their own independent

wireless alarm network.

Teach children how to respond to the alarm and that they should never play with the unit. Your Kidde

Smoke Alarm was designed for use in a residential environment. It is not designed for use in a recreational

vehicle (RV) or boat.

NOTE: Please take a few minutes to thoroughly read this user guide which should be saved for future

reference and passed on to any subsequent owner.

The National Fire Protection Association (NFPA) and the manufacturer recommend replacing this alarm

ten years from the date code on back of alarm.

Model (on back): _______________

Date Code (on back): _______________

Date of Purchase: _______________

Where Purchased: _______________

Date to Replace: _______________

Product Support: 1-800-880-6788

Please write down the below information

and have this at hand when you call.

Contents

1. Smoke Alarm: What To Do When The Alarm Sounds . . . . . . . . . . 4

2. Carbon Monoxide Alarm: What To Do When The Alarm Sounds . . . . . .5

3. Other Alarm Visual And Audible Indicators . . . . . . . . . . . . . . 6

4. Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . .7

5. Introduction, Product Features & Specifications . . . . . . . . . . . .8

6. Limitations Of Smoke Alarms . . . . . . . . . . . . . . . . . . . 9

7. Recommended Locations For Smoke Alarms . . . . . . . . . . . . . 10

8. Locations To Avoid . . . . . . . . . . . . . . . . . . . . . . .12

9. Activation And Wireless Alarm Network . . . . . . . . . . . . . . .13

9.1 Setting Up A Wireless Alarm Network . . . . . . . . . . . . . . 14

9.2 Adding Another Device to an Existing Wireless Alarm Network . . . . .16

9.3 Resetting a Device’s Wireless Settings . . . . . . . . . . . . . . 18

10. Operation And Testing . . . . . . . . . . . . . . . . . . . . .18

11. Recognizing Nuisance Alarms . . . . . . . . . . . . . . . . . . 20

12. Battery . . . . . . . . . . . . . . . . . . . . . . . . . . .22

13. Permanently Disable Alarm / Discharge Battery. . . . . . . . . . . . 23

14. Cleaning Your Alarm . . . . . . . . . . . . . . . . . . . . . .24

15. Good Safety Habits . . . . . . . . . . . . . . . . . . . . . . 25

16. Service And Warranty . . . . . . . . . . . . . . . . . . . . . 28

1. Smoke Alarm: What To Do When the Alarm Sounds

Smoke alarm pattern is three long beeps with voice “Fire!,” a 1.5 second pause, and three long beeps

repeating. The red LED blinks in time with alarm pattern.

•Alert small children in the home as well as anyone else that might have difficulty recognizing the

importance of the alarm sounding or that might have difficulty leaving the area without help.

•Leave immediately by your escape plan. Every second counts, so don’t waste time getting dressed or

picking up valuables.

•In leaving, don’t open any inside door without first feeling its surface. If hot, or if you see smoke

seeping through cracks, don’t open that door! Instead, use your alternate exit. If the inside of the

door is cool, place your shoulder against it, open it slightly and be ready to slam it shut if heat and

smoke rush in.

•If the escape route requires you to go through smoke, stay close to the floor where the air is cleaner.

Crawl if necessary, and breathe shallowly through a cloth, wet if possible.

•Once outside, go to your selected meeting place and make sure everyone is there.

•Call the fire department from your cell phone outside, or from your neighbour’s home—not from

yours!

•Don’t return to your home until the fire officials say that it is all right to do so.

There are situations where a smoke alarm may not be effective to protect against fire as stated in the NFPA

Standard 72. For instance:

a) smoking in bed

b) leaving children home alone

c) cleaning with flammable liquids, such as gasoline

NOTE: See Section 11. RECOGNIZING NUISANCE ALARMS, for nuisance alarm situations.

2. Carbon Monoxide Alarm: What To Do When the Alarm Sounds

NOTE : This is not a carbon monoxide (CO) alarm, but will receive and transmit a CO alarm signal

(with voice message) from an interconnected CO or combination smoke / CO alarm.

Carbon monoxide (CO) alarm pattern is four quick beeps with voice “Warning! Carbon Monoxide”

repeating every 5 seconds. The red LED blinks in time with alarm pattern.

warning: Carbon monoxide alarm aCtivation indiCates the presenCe of

Carbon monoxide (Co) at high ConCentrations whiCh Can kill you.

1. Immediately move to fresh air – outdoors or by an open door/window. Do a head count to check

that all persons are accounted for. Do not re-enter the premises nor move away from the open door/

window until the emergency services responders have arrived, the premises have been aired out, and

your alarm remains in its normal condition.

2. Call your local emergency service.

(fire department or 911)

Never restart the source of a CO problem until it has been corrected. Never ignore the sound of the

alarm!

NOTE: See Section 11. RECOGNIZING NUISANCE ALARMS, for nuisance alarm situations.

PHONE NUMBER

3. Other Alarm Visual and Audible Indicators

Operational Mode Visual Indications Audible Indications Action/Note:

Normal (standby) Green LED blink approx every

60 sec.

Test (button press

when no alarm condi-

tion is present)

• 4 patterns of Red/Amber/Green.

• Test: Red LED blinks in time

with alarm pattern. Safety light

will briey illuminate on model

P4010LDCS-WCA.

• Green LED fade on/o at test

complete

• Button press sound

• Voice: "Testing, this is very loud.

Press now to cancel test. 5, 4,

3, 2, 1."

• 3 long beeps, Voice "Fire!", 3 long

beeps, Voice "Test Complete,"

Power on/reset sound.

• Voice "Test Canceled" if button

pushed before test sequence begins.

Perform Test/Hush button

press once a week to verify

proper alarm operation

* Push/release button before

the countdown ends to

cancel test.

Smoke Alarm Memory

(unit has experienced

a smoke alarm event

within the last hour)

Red and Amber LED alternate on

1 sec, every 10 sec.

After button push: "Smoke

previously detected" only on the

initiating alarm unit.

Push test button to clear

Alarm Memory. NOTE:

standard test sequence will

follow. (Push/release button

again to cancel test).

Smoke Alarm Hush

Mode, (Hush®

Control)

Red LED blinks every 2 sec. After button push: "Hush Mode

Activated." Smoke alarm pattern

stops.

(If there is too much smoke to allow

Hush: Voice "Too Much Smoke,

Alarm cannot be Hushed" Smoke

alarm pattern continues.)

This feature is to be used

only when a known alarm

condition, such as smoke

from cooking, activates

the alarm.

Locate None After button push on non-initiating

unit, only initiating unit continues

alarm pattern.

Use this to quickly locate the

alarm source and determine

if alarm is nuisance or real.

Smoke Alarm Hush

Mode Canceled

None Voice message "Hush Mode

Canceled."

When smoke levels drop

below the alarm threshold,

the voice message "Hush

Mode Canceled" will occur .

Initiating Alarm,

(Multiple alarms in an

interconnected system)

Green LED blinks once per sec indi-

cating that this is the unit initiating

the alarm in an interconnected,

multiple alarm, system.

Unit in Smoke alarm mode. During alarm, the initiating

alarm red blink will be

interrupted by a green blink.

4. Troubleshooting Guide

Trouble Condition Visual Indications Audible Indications Action:

Low Battery

Amber

LED

blinks

every

5 seconds

Chirp every 60 sec, voice every

30 sec: “Replace alarm.”

Voice stops after 5 mins.

* Remove, discharge, dispose unit, and replace as

soon as possible.

Fault Mode Chirp every 30 sec.

Voice every 30 sec: “Error, see

trouble shooting guide”

After 5 mins: no voice message

* See Cleaning Your Alarm section.

* Push Test/Hush button once to attempt to

reset the unit .

* Red LED will blink out an error code (number of

blinks) when Test/Hush button is push/released

once. Report the number of blinks to customer

service if needed.

End of Unit Life Double chirp every 30 sec.

First 5 mins: Voice every 30 sec:

“Replace alarm, press button to

temporarily silence.” Voice stops

after 5 mins. After 7 days: Chirps

continue. Voice every 30 sec for

5 mins: “Replace alarm.”

* Push/release Test/Hush button to temporarily

silence (see End of Unit Life Hush Mode section

below)

* Remove, discharge, dispose unit, and replace as

soon as possible.

End of Unit Life Hush

Mode (after push/

release Test/Hush

button during End

of Life)

Voice “Temporarily Silenced.”

End of Unit Life chirps silenced

for 24 hrs. (7 days after End of

Unit Life chirps begin, the chirps

cannot be silenced.)

* Remove, discharge, dispose unit, and replace as

soon as possible.

Network Error Chime every 30 secs. Voice every

30 sec: “Connection lost. Press

button to temporarily silence.”

After 5 min: no voice messages

(Note: network must have 3 or

more alarms for voice messages.)

* Push/release the Test/Hush button once to

silence for 24 hrs at a time.

* Red LED will blink out an error code (number of

blinks) when Test/Hush button is push/released

once. Report the number of blinks to customer

service if needed.

* Push and hold Test/Hush button until two beeps

are heard (approx 4 sec) and then release the

button to try to rejoin. Or reset (section 9.3) and

then rejoin (section 9.2).

* If error persists, remove, discharge, and replace

alarm as soon as possible.

Network Error Hush

(after button push

during Network

Error)

Voice “Temporarily

Silenced.”

If you require further information please contact Product Support at 1-800-880-6788 or write us at:

Kidde Canada Inc., P.O. Box 40, Apsley, ON K0L 1A0. Our internet address is www.kiddecanada.com.

5. Introduction, Product Features and Specifications

INTRODUCTION

This alarm detects products of combustion using photoelectric technology. Ten (10) years after the unit

is installed, this unit will automatically alert you that it is time to replace the unit. This is called “End of

Unit Life” mode. See Troubleshooting Guide. To help identify the date to replace the unit, a label has

been affixed to the side of the alarm. Write in the “Replace by” date (10 years from initial power up) in

permanent marker on the label prior to installing the unit.

PRODUCT FEATURES AND SPECIFICATIONS:

•Temperature: Operating Range: 4.4°C (40°F) to 37.8°C (100°F)

•Humidity: Operating range: up to 95% RH non-condensing

•Audible Alarm: 85+ dB at 10’ 3.0 to 3.5 KHz pulsing alarm, with voice message “Fire!”

•NOTE: This is not a CO alarm, but it will receive and transmit a CO alarm signal (with voice message

“Warning! Carbon Monoxide”) from an interconnected CO or combination smoke/CO alarm.

•Smoke Sensor: Photoelectric

•Voice message system

•Smoke Alarm Hush®Control

•Ambient Light Sensing

•Powered by 3 V DC non-replaceable sealed lithium battery.

•Wireless interconnectable to other compatible alarms.

•One large, user- friendly button.

•LED safety light on model P4010LDCS-WCA to help illuminate escape pathways.

6. Limitations of Smoke Alarms

WARNING: PLEASE READ CAREFULLY AND THOROUGHLY

•Life safety from fire in residential occupancies is based primarily on early notification to occupants of

the need to escape, followed by the appropriate egress actions by those occupants.

•Fire warning systems for dwelling units are capable of protecting about half of the occupants in

potentially fatal fires. Victims are often intimate with the fire, too old or young, or physically or

mentally impaired such that they cannot escape even when warned early enough that escape

should be possible. For these people, other strategies such as protection-in-place or assisted escape

or rescue are necessary.

•Leading authorities recommend that both ionization and photoelectric smoke alarms be installed

to help insure maximum detection of the various types of fires that can occur within the home.

Ionization sensing alarms may detect invisible fire particles (associated with fast flaming fires) sooner

than photoelectric alarms. Photoelectric sensing alarms may detect visible fire particles (associated

with slow smoldering fires) sooner than ionization alarms.

•A battery powered alarm must have a battery of the specified type, in good condition and installed

properly (This model has a sealed battery).

•Smoke alarms must be tested regularly to make sure the battery and the alarm circuits are in good

operating condition.

•Smoke alarms cannot provide an alarm if smoke does not reach the alarm. Therefore, smoke alarms

may not sense fires starting in chimneys, walls, on roofs, on the other side of a closed door or on a

different floor.

•If the alarm is located outside the bedroom or on a different floor, it may not wake up a sound sleeper.

•The use of alcohol or drugs may also impair one’s ability to hear the smoke alarm. For maximum

protection, a smoke alarm should be installed in each sleeping area on every level of a home.

This alarm is not intended to alert hearing impaired individuals.

7. Recommended Locations for Smoke Alarms

•Locate smoke alarms in all sleeping areas. Try to monitor the exit path as the bedrooms are usually farthest

from the exit. If more than one sleeping area exists, locate additional alarms in each sleeping area.

•Locate additional alarms to monitor any stairway as stairways act like chimneys for smoke and heat.

•Locate at least one alarm on every floor level.

•Locate an alarm in every bedroom.

•Locate an alarm in every room where electrical appliances are operated (i.e. portable heaters or humidifiers).

•Locate an alarm in every room where someone sleeps with the door closed. The closed door may

prevent an alarm not located in that room from waking the sleeper.

•Smoke, heat, and combustion products rise to the ceiling and spread horizontally. Mounting the

smoke alarm on the ceiling in the center of the room places it closest to all points in the room. Ceiling

mounting is preferred in ordinary residential construction.

ANYWHERE ALONG

THIS BOLD SURFACE

Locations permitted for smoke

alarms and smoke detectors

on tray-shaped ceilings.

(4")

10cm

(4")

10cm

(12")

30.5

(12")

30.5cm

(3')

0.9m

(3')

0.9m

(3')

0.9m

ANYWHERE ALONG

THIS BOLD SURFACE

Locations permitted for smoke

alarms and smoke detectors

on tray-shaped ceilings.

(4")

10cm

(4")

10cm

(12")

30.5cm

(12")

30.5cm

(3')

0.9m

(3')

0.9m

(3')

0.9m

ANYWHERE ALONG

THIS BOLD SURFACE

Locations permitted for smoke

alarms and smoke detectors

on tray-shaped ceilings.

(4")

10cm

(4")

10cm

(12")

30.5cm

(12")

30.5cm

(3')

0.9m

(3')

0.9m

(3')

0.9m

ANYWHERE ALONG

THIS BOLD SURFACE

Locations permitted for smoke

alarms and smoke detectors

on tray-shaped ceilings.

(4")

10cm

(4")

10cm

(12")

30.5cm

(12")

30.5cm

(3')

0.9m

(3')

0.9m

(3')

0.9m

ANYWHERE ALONG

THIS BOLD SURFACE

Locations permitted for smoke

alarms and smoke detectors

on tray-shaped ceilings.

(4")

10cm

(4")

10cm

(12")

30.5cm

(12")

30.5cm

(3')

0.9m

(3')

0.9m

(3')

0.9m

ANYWHERE ALONG

THIS BOLD SURFACE

Locations permitted for smoke

alarms and smoke detectors

on tray-shaped ceilings.

(4")

10cm

(4")

10cm

(12")

30.5cm

(12")

30.5cm

(3')

0.9m

(3')

0.9m

(3')

0.9m

NFPA 72 states: “Smoke alarms in rooms with

ceiling slopes greater than 0.3 m in 2.4m (1ft in

8 ft) horizontally shall be located on the high side

of the room.” NFPA 72 states: “A row of detectors

shall be spaced and located within 0.9 m (3ft) of

the peak of the ceiling measured horizontally.”

Figure 7-A

Figure 7-B Figure 7-C

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Detector de humo de Kidde

Kidde

Kidde P1235CA Manual de usuario

Kidde

Kidde P4010ACLEDSCA-2 Manual de usuario

Kidde

Kidde 976 Manual de usuario

Kidde

Kidde P9050 Manual de usuario

Kidde

Kidde VM-1 Manual de usuario

Kidde

Kidde 916 Manual de usuario

Kidde

Kidde 3050-VDSC10 Manual de usuario

Kidde

Kidde 1276CA Manual de usuario

Kidde

Kidde 915 Manual de usuario

Kidde

Kidde 0910KCA Manual de usuario

Kidde

Kidde TRUSENSE SMOKE Manual de usuario

Kidde

Kidde P4010ACS-WCA Manual de usuario

Kidde

Kidde 1235CA Manual de usuario

Kidde

Kidde FIREX 4985 Manual de usuario

Kidde

Kidde PI9000 Manual de usuario

Kidde

Kidde P9040 Manual de usuario

Kidde

Kidde FADC230 Manual de usuario

Kidde

Kidde 2030-DSR Manual de usuario

Kidde

Kidde P3010L-CO-CA Manual de usuario

Kidde

Kidde RF-SM-DC Manual de usuario

Kidde

Kidde I12020 Manual de usuario

Kidde

Kidde P3010CUCA Manual de usuario

Kidde

Kidde PI9000CA Manual de usuario

Kidde

Kidde i4618AC Manual de usuario

Manuales populares de Detector de humo de otras marcas

x-sense

x-sense SD19-W Manual de usuario

BRK electronic

BRK electronic First Alert P1010 Manual de usuario

FireAngel

FireAngel Thermoptek ST-622 Manual de usuario

teko

teko Astra-42A Manual de usuario

Safetec

Safetec SDS-2/6 Manual del propietario

Siemens

Siemens PE-11C Manual de usuario

System Sensor

System Sensor DH500ACDC Manual de usuario

Resolution Products

Resolution Products RE612 CryptiX Manual de usuario

First Alert

First Alert PC900V Manual de usuario

Eminent

Eminent EM6590 E-Domotica Manual de usuario

Ei Electronics

Ei Electronics Ei Ei168RC Manual de usuario

Carrier

Carrier Kidde Quell Q301 Manual de usuario

VESDA

VESDA VLF-500 Manual de usuario

ELRO

ELRO FS8110 Manual de usuario

Heiman

Heiman SMOKI NS-626PHS Manual de usuario

Regin

Regin SDD-S65 Manual de usuario

Family Gard

Family Gard FG225 Manual de usuario

Greystone

Greystone DSD120 Manual de usuario