Kidde I9060CA Manual de usuario

Manual P/N 820-1496 Rev. A 04/08

ATTENTION: Please take a few minutes to thoroughly read this

user’s guide, which should be saved for future reference and

passed on to any subsequent owner.

Smoke Alarm

User’s Guide

i9060CA and i9080CA

i9060CA

with Safety Light

i9080CA

9VBattery Operated

SINGLE STATION

SMOKE ALARM

Introduction . . . . . . . . . . . . . . . . . . . . . . . . 1

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-11

Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . 12-15

Fire Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . 16-19

Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-21

Contents

Introduction

Thank you for purchasing this smoke alarm. It is an important

part of your family’s home safety plan. You can trust this

product to provide the highest quality safety protection. We

know you expect nothing less when the lives of your family are

at stake.

Please take a few minutes to thoroughly read this alarm manual,

and save it for future reference. Teach children how to respond

to the alarms, and that they should never play with the unit.

If you have any questions about the operation or installation of

your alarm, please call our toll free Consumer Hotline at

1-800-880-6788.

Image 1C will help you determine the correct location of safety

products that will help make your home a safer place.

Made in China. Patents Pending

Kidde Canada Inc.

P.O. Box 40, Apsley, ON K0L 1A0

www.kiddecanada.com

Models i9060CA and i9080CA are designed to detect products

of combustion using the ionization technique. They contain 0.9

microcurie of Americium 241, a radioactive material. Distributed

under U.S. NRC License No. 32-23858-01E. Manufactured in

compliance with U.S. NRC safety criteria in 10 CFR 32.27. The

purchaser is exempt from any regulatory requirements. Do not

try to repair the smoke alarm yourself. Refer to the instructions

in Warranty section for service.

WARNING: Battery door will not close unless battery is present.

Removal of battery will render the smoke alarm inoperative.

NOTE: Any statements referring to a battery, applies to both

batteries used with the i9080CA.

IMPORTANT: Read all instructions before installation and keep

this manual near the alarm for future reference.

Do not try to repair the smoke alarm yourself. Refer to the

instructions in Warranty section for service.

Installation

Recommended Locations

• Locate the first alarm in the immediate area of the sleeping

rooms. Try to monitor the exit path, as the sleeping rooms are

usually farthest from the exit. If more than one sleeping area

exists, locate additional alarms in each sleeping area (Image 1A).

• Locate additional alarms to monitor any stairway as stairways act

like chimneys for smoke and heat.

• Locate at least one alarm on every floor level (Image 1B).

• Locate an alarm in every sleeping room.

• Locate an alarm in every room where electrical appliances are

operated (i.e. portable heaters or humidifiers).

• Locate an alarm in every room where someone sleeps with the

door closed. The closed door may prevent an alarm not located in

that room from waking the sleeper.

• Smoke, heat, and combustion products rise to the ceiling and

spread horizontally. Mounting the smoke alarm on the ceiling in

the center of the room places it closest to all points in the room.

Ceiling mounting is preferred in ordinary residential construction.

• For mobile home installation, select locations carefully to avoid

thermal barriers that may form at the ceiling. For more details, see

Mobile Homes.

• When mounting an alarm on the ceiling, locate it at a minimum of

10 cm (4") from the side wall (Image 2A).

• When mounting the alarm on the wall, use an inside wall with the

top edge of the alarmat a minimum of 10 cm (4") and a

maximum of 30.5 cm (12") below the ceiling (Image 2A and 2B).

• Put smoke alarms at both ends of a hallway or large room if the

hallway or room is more than 9.1 m (30 ft) long. For large rooms,

one smokealarmis recommended for every 500 square feet of

floor space.

• Install smoke alarms on sloped, peaked or cathedral ceilings at or

within 0.9 m (3') of the highest point (measured horizontally).

NFPA72 states: “Smoke alarms in rooms with ceiling slopes

greater than 0.3 m in 2.4 m (1 foot in 8 feet) horizontally shall be

located on the high side of the room.” NFPA 72 states: “A row of

detectors shall be spaced and located within 0.9 m (3') of the peak

of the ceiling measured horizontally” (Image 2B and 2C).

Installation

DINING

ROOM

LIVING

ROOM

Smoke Alarms for Minimum Protection

Ionization Type Smoke Alarm with

Hush

Control or Photoelectric Type

Smoke Alarms for Additional Protection

KITCHEN BEDROOM

BEDROOM

LIVING

ROOM KITCHEN

BEDROOMBEDROOM HALL

BASEMENT

IMAGE 1A

IMAGE 1C

IMAGE 1B

SINGLE FLOOR PLAN MULTIPLE FLOOR PLAN

BEDROOM

FAMILY ROOM

WORKSHOPBASEMENT

KITCHEN

HALL

GARAGE

MASTER

BEDROOM

FIRE

EXTINGUISHERS

SMOKE

ALARMS

CARBON

MONOXIDE

ALARMS

TALKING

SMOKE/CO

ALARM

TOTAL HOME PROTECTION

• In homes that are not well insulated, extreme heat or cold can

be transferred from the outside to the inside through poorly

insulated walls and roof. This may create a thermal barrier

which can prevent the smoke from reaching an alarm mounted

on the ceiling. If you are not sure about the insulation in your

home, or if you notice that the outer walls and ceiling are either

hot or cold, install the alarm on an inside wall. In such homes,

install the smoke alarm with the top edge of the alarm at a

minimum of 10 cm (4") and a maximum of 30.5 cm (12")

below the ceiling (Image 2A).

Installation

• Install Smoke Alarms on tray-shaped ceilings (coffered ceilings) on

the highest portion of the ceiling or on the sloped portion of the

ceiling within 12” (305mm) vertically down from the highest point

(Image 2D).

Locations to Avoid

• Do not install within 0.9 m (3') of the following: The door to a

kitchen, or a bathroom that contains a tub or shower, forced

air supply ducts used for heating or cooling, ceiling or whole

house ventilating fans, or other high air-flow areas.

• Do not place the alarm where drapes or other objects will

block the sensor. Smoke must be able to reach the sensor to

accurately detect conditions.

• Do not install in peaks of vaulted ceilings, “A” frame ceilings

or gabled roofs. (Less than 10 cm (4") from the peak of an “A”

frame type ceiling.)

• Install at least 30.5 cm (12") away from fluorescent lights as

electronic noise may cause nuisance alarms.

• Keep out of insect infested areas. Avoid excessively dusty, dirty

or greasy areas. Dust particles may cause nuisance alarms or

failure to alarm.

• Extreme temperatures may effect the sensitivity of the alarm.

Do not install in areas where the temperature is colder than

4.4°C (40°F) or hotter than 37.8°C (100°F), such as garages

and unfinished attics.

•Do not install in areas where the relative humidity (RH) is

greater than 85%. Very humid areas, with moisture or steam,

can cause nuisance alarms.

• Avoid placing ionization smoke alarms in kitchen areas.

Normal cooking may cause nuisance alarms. If a kitchen alarm

is desired, it should have an alarm silence feature or be a

photoelectric type.

• Do not place in the garage. Particles of combustion are

present when you start your automobile.

• Smoke alarms are not to be used with detector guards unless

the combination (alarm and guard) has been evaluated and

found suitable for thatpurpose.

Installation

IMAGE 2A

IMAGE 2C

HORIZONTAL DISTANCE FROM PEAK

CEILING

10 cm (4”)

MINIMUM

10 cm (4”)

MINIMUM

30.5 cm (12”)

MAXIMUM

SIDE WALL

BEST

PLACEMENT

ACCEPTABLE

PLACEMENT

NEVER HERE

STAGNANT

AIR

10 cm (4”)

0.9 m (3’) 0.9 m (3’)

NOTIN

THIS AREA

ANYWHERE IN THIS

AREA

10 cm (4”)

NOT IN

THIS AREA

ANYWHERE IN THIS

AREA

0.9 m (3’)

IMAGE 2B

Installation

Mounting

CAUTION: This unit is sealed. The cover is not removable!

NOTE: Any statements referring to a battery, applies to both

batteries used with the i9080CA.

NOTE: Any statements referring to a battery reminder tab,

applies to both battery reminder tabs used with the i9080CA.

• Remove the mounting plate from the back of the alarm by

holding the plate and twisting the alarm in the direction

indicated by the “OFF” arrow on the alarm cover.

• To ensure aesthetic alignment of the alarm with the hall-way,

or wall, the “A” line on the mounting plate should be parallel

with the hallway when ceiling-mounted, or horizontal when

wall mounted (Image 3A).

• Secure the mounting plate to the wall or ceiling with the

anchors and screws provided (Image 3B).

• For aesthetic reasons, the suggested position for wall mounting

is with the button(s) facing down (Image 3C).

• Press the battery reminder tab down into the battery

compartment while inserting the battery (Image 3E).

CAUTION: If the battery reminder tab is not held down in the

battery compartment by the battery, the battery door will not

close and the unit will not attach to the mounting plate.

•Alignment marks are provided on the edge of the mounting

plate and the alarm. After installing the mounting plate, place

the alarmonto the mounting plate, making sure the alignment

marks are lined up. Twist the alarm in the direction indicated by

the “ON” arrow on the alarm cover (Image 3D) until it locks

in place.

ANYWHERE IN THIS

AREA

30 cm (12")

IMAGE 2D

Installation

Alarm Tamper Resist Feature

• To make the smoke alarm tamper-resistant, a locking pin has

been provided in the bag with the screws and anchors. Using

this pin will help deter children and others from removing the

alarm from the mounting plate. To use the pin, insert it into

the hole in the side of the alarm after the alarm has been

installed on the mounting plate (Image 3F).

NOTE: The tamper-resistant pin will have to be removed in order

to change the battery. Use long nose pliers to pull the pin out of

the hole. It is now possible to remove the alarm from the

mounting plate.

Mobile Homes

Modern mobile homes have been designed and built to be energy

efficient. Install smoke alarms as recommended in Recommended

Locations and Image 2A.

In mobile homes that are not well insulated compared to present

standards, extreme heat or cold can be transferred from the

outside to the inside through poorly insulated walls and roof. This

may create a thermal barrier that can prevent the smoke from

reaching an alarm mounted on the ceiling. In such units, install

the smoke alarm on an inside wall with the top edge of the alarm

at a minimum of 10 cm (4") and a maximum of 30.5 cm (12")

below the ceiling (Image 2A and 2B).

If you are not sure about the insulation in your mobile home, or

if you notice that the outer walls and ceiling are either hot or

cold, install the alarm on an inside wall. For minimum protection,

install at least one alarm close to the sleeping rooms. For

additional protection, see Image 1A and 1B.

WARNING: Test your smoke alarm operation after R.V.or mobile

home vehicle has been in storage, before each trip and at least

once a week during use.

Installation

A A

THIS SIDE UP FOR WALL MOUNTING

FACE VERS LE HAUT POUR INSTALLATION MURALE

5 5

IMAGE 3A IMAGE 3B

IMAGE 3C IMAGE 3D

“A” LINE

ALIGNMENT MARKS

SUGGESTED WALL

MOUNTING POSITION ROTATE TO MOUNT OR

TOREMOVE

IMAGE 3E

BATTERY

REMINDER TAB

IMAGE 3F

TAMPER-RESIST

LOCKING PIN

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Detector de humo de Kidde

Kidde

Kidde Smoke Alarm Manual de usuario

Kidde

Kidde KF1 Manual de usuario

Kidde

Kidde 915 Manual de usuario

Kidde

Kidde i9040EU Manual de usuario

Kidde

Kidde P4010ACSAQ-WF Manual de usuario

Kidde

Kidde RF-SND Manual de usuario

Kidde

Kidde Slick 1SF23/9HI Instrucciones de montaje

Kidde

Kidde 0918LL Manual de usuario

Kidde

Kidde P3010K-CO Manual de usuario

Kidde

Kidde P4010ACS-WF Manual de usuario

Kidde

Kidde i12060A Manual de usuario

Kidde

Kidde TRUSENSE 3050-VASC10 Manual de usuario

Kidde

Kidde Fyrewatch 0913 Manual de usuario

Kidde

Kidde P4010ACSCO Manual de usuario

Kidde

Kidde 976 Manual de usuario

Kidde

Kidde KN-COSM-BCA Manual de usuario

Kidde

Kidde I12020 Manual de usuario

Kidde

Kidde P4010ACSCO-W Manual de usuario

Kidde

Kidde 2070-VASR Manual de usuario

Kidde

Kidde 0910UK Instrucciones de montaje

Kidde

Kidde P12040 Manual de usuario

Kidde

Kidde i9010UK Manual de usuario

Kidde

Kidde Fyrewatch 0913 Manual de usuario

Kidde

Kidde P4010DCSCO-W Manual de usuario

Manuales populares de Detector de humo de otras marcas

x-sense

x-sense SD19-W Manual de usuario

BRK electronic

BRK electronic First Alert P1010 Manual de usuario

FireAngel

FireAngel Thermoptek ST-622 Manual de usuario

teko

teko Astra-42A Manual de usuario

Safetec

Safetec SDS-2/6 Manual del propietario

Siemens

Siemens PE-11C Manual de usuario

System Sensor

System Sensor DH500ACDC Manual de usuario

Resolution Products

Resolution Products RE612 CryptiX Manual de usuario

First Alert

First Alert PC900V Manual de usuario

Eminent

Eminent EM6590 E-Domotica Manual de usuario

Ei Electronics

Ei Electronics Ei Ei168RC Manual de usuario

Carrier

Carrier Kidde Quell Q301 Manual de usuario

VESDA

VESDA VLF-500 Manual de usuario

ELRO

ELRO FS8110 Manual de usuario

Heiman

Heiman SMOKI NS-626PHS Manual de usuario

Regin

Regin SDD-S65 Manual de usuario

Family Gard

Family Gard FG225 Manual de usuario

Greystone

Greystone DSD120 Manual de usuario

Kidde i9060CA Manual de usuario

Manuales populares de Detector de humo de otras marcas