Kidde CTM City Tie Instrucciones de montaje

P/N 3101025-EN • REV 03 • ISS 16NOV15 1 / 2

CTM City Tie Module

Installation Sheet

Description

The CTM City Tie Module provides a single municipal box connection

for activating a local energy type master box connected to a public fire

alarm reporting system.

Installation

Install the CTM in accordance with NFPA 70 National Electrical Code.

WARNING: This device will not operate without electrical power. As

fires frequently cause power interruptions, we suggest you discuss

further safeguards with your fire protection specialist.

The CTM is shipped from the factory as an assembled unit; it contains

no user-serviceable parts and should not be disassembled.

For more information, refer to the technical reference manual listed

inside the control panel door.

To install the module:

1. Verify that all field wiring is free of opens, shorts, and ground

faults.

2. Make all wiring connections as shown in the wiring diagram. See

Figure 1.

3. Using the 4-24 × 1/2 in (13 mm) self-tapping screw provided,

mount the wall plate to the module.

4. Using the two 6-32 × 1/2 in (13 mm) machine screws provided,

mount the module to the electrical box.

Wiring

Wire the CTM to a dedicated notification appliance circuit (NAC) as in

Figure 1 on page 2. Do not install other notification appliances on the

same circuit.

Specifications

Voltage

24 VDC nom.

Current

Standby

Alarm

20 mA

300 mA, max.

Ground fault impedance

0 Ω

Wire size

12 to 18 AWG (0.75 to 2.5 sq mm)

Mounting

North American 2-1/2 in (64 mm) deep

1-gang box

Municipal box connection

Wire resistance:

Trip current:

26 Ω

200 mA into a 14.5 Ω coil

Operating environment

Temperature

Relative humidity

32 to 120°F (0 to 49°C)

0 to 93% noncondensing

Contact information

For contact information, see www.edwardsfiresafety.com.

firealarmresources.com

2 / 2 P/N 3101025-EN • REV 03 • ISS 16NOV15

Figure 1: CTM installation wiring diagram

[1] Power-limited and supervised for opens, shorts, and ground faults

[2] Nonpower-limited and supervised for opens and ground faults only.

26 Ω, max. 4.4 A, max.

[3] Use end-of-line resistor value required by the notification appliance

circuit

[4] NAC output signal must be compatible with the input rating of the

local energy type master box.

1234

– ActiveNormal

Public fire alarm

reporting system

Local energy type

master box

–

– +

–

EOLR [3]

ActiveNormal

From dedicated notification

appliance circuit [4]

Compatible electrical box

CTM

Wall plate

Screws

14.5 Ω

trip coil

[1]

[2]

firealarmresources.com

Otros manuales de Unidad de control de Kidde

Kidde

Kidde GSA-UM Instrucciones de montaje

Kidde

Kidde Alarmline II Manual de usuario

Kidde

Kidde AEGIS Manual de usuario

Kidde

Kidde CO120X Manual de usuario

Kidde

Kidde FX-2WIRE Instrucciones de montaje

Kidde

Kidde GSA-CC1 Instrucciones de montaje

Kidde

Kidde FX-IDC1A Instrucciones de montaje

Kidde

Kidde GSA-REL Manual del producto

Kidde

Kidde FX-IDCWS Instrucciones de montaje

Kidde

Kidde ARIES Manual de usuario

Kidde

Kidde AEGIS 84-732001-001 Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario