Kidde KN-COPP-3 Manual de usuario

Model KN-COPP-3

900-0099

P/N 820-1028 Rev. A

SINGLE STATION

CARBON MONOXIDE

ALARM

120 V AC and Self-recharging Battery Backup

CARBON MONOXIDE

ALARM

with Digital Display, Test, and Peak Level Memory

Alarm Manual

ATTENTION: Please

take a few minutes to

thoroughly read this

manual, which should

be saved for future

reference and passed

on to any subsequent

owner. If you have any

questions about the

operation or installation

of your alarm, please call

our toll-free hotline at

1-800-880-6788.

Introduction . . . . . . . . . . . . . . . . . . . . . . . . 1

Quick Set-up . . . . . . . . . . . . . . . . . . . . . . . . . 2–3

Illustration . . . . . . . . . . . . . . . . . . . . . . . . . 4

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–6

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . 7–14

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 15–19

Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . 20

Carbon Monoxide Safety . . . . . . . . . . . . . . . 21–27

Specifications. . . . . . . . . . . . . . . . . . . . . . . . 28–29

Display Readings . . . . . . . . . . . . . . . . . . . . . 30–32

Li-Ion Battery Handling Precautions . . . . . 32–33

Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Contents

IMPORTANT: THIS CARBON MONOXIDE ALARM IS DESIGNED TO

DETECT CARBON MONOXIDE FROM ANY SOURCE OF IMPROPER OR

MALFUNCTIONING APPLIANCES. IT IS NOT DESIGNED TO DETECT

SMOKE, FIRE, OR ANY OTHER GAS.

WARNING: THIS CARBON MONOXIDE ALARM IS NOT A SUBSTITUTE

FOR INSTALLING AND MAINTAINING AN APPROPRIATE NUMBER OF

SMOKE ALARMS IN YOUR HOME.

WARNING: THIS CARBON MONOXIDE ALARM WILL NOT SENSE

SMOKE, FIRE, OR ANY POISONOUS GAS OTHER THAN CARBON

MONOXIDE. FOR THIS REASON YOU MUST INSTALL SMOKE ALARMS

TO PROVIDE EARLY WARNING OF FIRE AND TO PROTECT YOU AND

YOUR FAMILY FROM FIRE AND ITS RELATED HAZARDS. NOT SUITABLE

FOR INSTALLATION IN HAZARDOUS LOCATIONS.

DURING A POWER OUTAGE, UNIT WILL OPERATE FOR A PERIOD OF

AT LEAST TWENTY HOURS ON A FULLY CHARGED KIDDE

RECHARGEABLE BATTERY PACK.

WARNING: THIS PRODUCT IS INTENDED FOR USE IN ORDINARY

INDOOR RESIDENTIAL AREAS. IT IS NOT DESIGNED TO MEASURE

COMPLIANCE WITH COMMERCIAL AND INDUSTRIAL STANDARDS.

THE INSTALLATION OF THIS DEVICE SHOULD NOT BE USED AS A

SUBSTITUTE FOR PROPER INSTALLATION, USE AND MAINTENANCE OF

FUEL-BURNING APPLIANCES, INCLUDING APPROPRIATE VENTILATION

AND EXHAUST SYSTEMS.

This Kidde carbon monoxide (CO) alarm is an important part of

your family’s home safety plan. Because CO alarms for the home

haven’t been available until recently, most people haven’t had

much experience using them. As a new owner of a CO alarm,

there are some basic facts you should know for your protection

and convenience.

Many people think that CO alarms operate like smoke alarms. And

in some basic ways, this is true. Like smoke alarms, CO alarms

monitor the air in your home and sound a loud alarm to warn

you of trouble.

But, the similarities end here. The way you respond to a CO alarm

is quite different than that of a smoke alarm. That’s because a

house fire and a carbon monoxide problem are two distinctly

different situations. If your smoke alarm were to alarm, you would

quickly be able to judge the level of danger you were in (if any)

with your five senses: you could see and smell the smoke, you

could feel the heat, you could see and even hear the fire burning.

You could also readily see if your smoke alarm were alarming in

a non-emergency situation, say if someone smoked up the kitchen

with some seriously burnt toast. Because your sense of sight,

smell, hearing and touch give you so much information, you

could almost instantly judge what action to take if you heard your

smoke alarm.

Carbon monoxide (CO) is invisible, odorless, tasteless and non-

irritating–completely undetectable to your five senses. That’s why

it’s so important to your safety that you have a carbon monoxide

alarm. But, how do you know what to do if your unit alarms?

You have to learn what to do, because your five senses won’t tell

you. That’s why this user’s guide is so important. Please take the

time to read this guide from cover to cover, to familiarize yourself

with the facts about carbon monoxide, how your new unit works,

and what to do if it alarms. Then, find a handy place to keep the

guide so it will be readily available in the future when you have a

question. For more information on this product call our toll-free

customer service hotline at 1-800-880-6788.

Thank you for making Kidde a part of your complete home safety

program. With proper installation and use, your new Kidde CO

alarm should provide you with years of dependable service.

Introduction

Quick Set-Up

We urge you to read this entire manual in the sequence it

is presented. But, if you only read one part of this guide

initially, read this page! Listed below are seven easy steps

for setting up your unit. Please read the entire guide for

complete information.

Step 1

Determine the best location for your CO alarm(s). Refer to

Page 7 for complete information.

Step 2

Your CO alarm is equipped to be mounted as a corded unit,

a direct plug unit, or a tabletop unit. In the “as shipped”

configuration, the unit can be plugged directly into a wall

socket (if your outlets are mounted horizontally, please

refer to page 10). If the transformer / adaptor is taken out

of the unit, the alarm can be mounted on the wall at eye

level, while the transformer is plugged into a wall socket.

The unit can also be set on a table if the support at the

bottom of the unit is pulled out (see “rear view” illustration

on page 4). Refer to page 11 for further information on

installing your alarm.

Step 3

A rechargeable battery pack is provided for backup in the

event of a power outage. To install the battery pack, open

the back door and align the connector with the slot in the

battery. Insure the orientation of the two alignment ribs

align with the slot in the battery. Press the connector in

until it is fully seated. Depending on the charge state of the

battery pack (the battery packs can have different amounts

of energy stored in them due to storage time), you may

hear the alarm sound briefly to indicate the alarm is

receiving power. Place battery pack into battery

compartment and replace back door.

Note: Battery backup will be limited until the battery has

fully charged. It may take up to 24 hours for the battery

back up to fully charge.

Quick Set-Up

Step 4

Plug the alarm into a standard, unswitched 120 volt AC

electric outlet in one of the configurations listed in step 2.

Step 5

If the battery pack has a full charge when first powered

up, you will see three eights in the digital display

indicating the alarm is warming up. After approximately 20

seconds, the first reading will be displayed. The number

on the display should be “0”. If the battery pack is partially

charged,“Lb”(Low battery) will flash every second alternating

with a “0” until the battery is charged.

Step 6

Make sure the red dot in the digital display is blinking.

Then test the unit’s operation by pressing and releasing

the Test / Reset button. Within 15 seconds you will hear 4

quick “chirps”–followed by 5 seconds of silence–followed

by 4 quick “chirps”.

Step 7

While testing the alarm, have someone else check that the

alarm can be heard easily from the sleeping areas. The

alarm should be located where it can wake you if it

alarms at night. See page 7 for complete information on

the best locations for your alarm.

Caution: Continuous exposure to the loud 85 decibel (db)

alarm at close range over an extended period of time may

cause hearing loss.

Your Kidde CO alarm is now monitoring for the presence

of carbon monoxide.

Illustration

Digital Display

Blinking Red Dot

Test/Reset Button

Peak Level Button

Front View

Rear View

Adaptor Release

Removable Adaptor

Door Latch (4 corners)

Back Door

Cord Recess

Key Hole

Slide Support for Table-Top

Grip for Back Door

Removal (Slide Down)

Power Cord

Adaptor Cord

Strain Relief

Rechargeable Backup

Battery (shown

installed)

Install Backup Battery

For correct installation,

refer to Quick Set-Up

and refer to Installation

on page 12.

Rear View - Back Door Removed

Sounder Alarm

Digital Display

The continuous digital display shows you the level of carbon

monoxide (if any) the unit is sensing. The unit updates this

reading every 15 seconds so you can watch levels rise or fall.

Test/Reset Button

This button has three functions. First, this is the button you

press when you test the unit weekly. Secondly, you press this

button if the unit alarms and you want to silence the alarm.

This will reset the unit and it will then again start monitoring

for CO. Finally the Test / Reset button is used to reset the peak

level memory.

Peak Level Button

By pressing this button, you can see the peak CO level

recorded by the alarm since it was last cleared or unplugged.

Sensor

The CO sensor is a highly sensitive, electrochemical sensor

that is CO-specific to help avoid false alarms.

Sounder Alarm

The sounder alarm is the loud 85 decibel (db) pulsing alarm

that will sound to alert you to a potential problem.

Keyholes

The keyholes located on the back of the alarm slide onto the

screws located in the wall.

Pull-Out Transformer/Adaptor

This unique feature enables the alarm to be used as a direct

plug unit, a wall-mounted unit or a tabletop unit.

Rechargeable Backup Battery

The rechargeable battery pack is to supply a short-term

backup during a power outage. In the event of a power

outage, the rechargeable battery pack will continue operating

the alarm for at least 20 hours.

Features

What This Alarm Can and Cannot Do

CO alarms designed to sense unacceptable levels of CO

from malfunctioning furnaces, appliances, gasoline engines

or other sources.

CO alarms provide early warning of the presence of

carbon monoxide, usually before a healthy adult would

experience symptoms.

This early warning is possible, however, only if your alarm

is located, installed and maintained as described in this

alarm manual.

When on AC power, this unit is designed to act as a

monitor. It is not designed for use as a short-term testing

device to perform a quick check for the presence of CO.

Alarms have limitations. Like any other electronic device, CO

alarms are not fool-proof.

CO alarms have a limited operational life. You must test

your alarm weekly, because it could fail to operate at any

time. If your alarm fails to test properly, or if its self-

diagnostic test reveals a malfunction, immediately have the

unit replaced.

CO alarms can only sense CO that reaches the unit’s sensor.

CO may be present in other areas without reaching the alarm.

The rate at which CO reaches the unit may be affected by

doors or other obstructions. In addition, fresh air from a vent

or open window or any other source may prevent CO from

reaching the sensor.

CO could be present on one level of the home and not reach

the alarm installed on a different level. For example, CO in

the basement may not reach an alarm on the second level,

near the bedrooms. For this reason, we recommend you

provide complete coverage by placing a CO alarm on every

level of the home.

CO alarms should not be used to detect the presence of natural

gas (methane), propane, butane, or other combustible fuels.

CO alarms are not a substitute for property, disability, life

or other insurance of any kind. Appropriate insurance

coverage is your responsibility. Consult your insurance

agent.

Features

Installation

Recommended Installation Locations

Your Kidde CO alarm should be mounted in or near bedrooms

and living areas. It is recommended that you install a Kidde

CO alarm on each level of a multi-level home. You may use

the number and location of smoke alarms installed in your

home according to current building code requirements as a

guide to the location of your Kidde CO alarm(s).

When choosing your installation locations or the number of

alarms that may be required, make sure that you can hear the

alarm from all sleeping areas. If you install only one carbon

monoxide alarm in your home, install the alarm near

bedrooms, not in the basement or furnace room.

Two labels have been provided with important information

on what to do in case of an alarm. Add the phone number

of your emergency service provider in the space provided.

Place one label next to the alarm after it is mounted, and

one label near a fresh air source such as a door or window.

CAUTION:This alarm will only indicate the presence of

carbon monoxide at the sensor. Carbon monoxide may be

present in other areas.

IMPORTANT: Improper location can affect the sensitive

electronic components in this alarm. Please see the next

section describing where NOT to install this alarm.

DINING KITCHEN BEDROOM BEDROOM

BEDROOMLIVING ROOM

Recommended Locations

Installation

Locations To Avoid

To avoid causing damage to the unit, to provide optimum

protection, and to prevent unnecessary alarms, follow the

directions below where NOT to install this alarm:

It is recommended that you DO NOT install this CO alarm

in garages, kitchens or furnace rooms. Installation in these

areas could lead to nuisance alarms, may expose the sensor

to substances that could damage or contaminate it, or the

alarm may not be heard by persons in other areas of the

home, especially if they are sleeping.

In the garage, vehicle exhaust can contain some carbon

monoxide. These levels are higher when the engine is first

started. Within hours of starting a vehicle and backing it

out of the garage, the levels present over time can activate

the alarm and become a nuisance.

In the kitchen and furnace room, some gas appliances can

emit a short burst of carbon monoxide upon start-up. This

is normal. If your CO alarm is mounted too close to these

appliances, it may alarm often and become a nuisance.

If you must install the unit near a cooking or heating

appliance, install AT LEAST 1.5 m (5') away from the

appliance.

Do not install in excessively dusty, dirty or greasy areas

such as kitchens, garages and furnace rooms. Dust grease

or household chemicals can contaminate or coat the

alarm’s sensors, causing the alarm not to operate properly.

Do not obstruct the vents located at the top and bottom of

the alarm. Place the alarm where drapes, furniture or other

objects do not block the flow of air to the vents.

Do not install in dead air spaces, such as peaks of vaulted

ceilings or gabled roofs, where carbon monoxide may not

reach the sensor in time to provide early warning.

Otros manuales para KN-COPP-3

Tabla de contenidos

Otros manuales de Alarma de monóxido de carbono de Kidde

Kidde

Kidde KN-COP-DP-10YL Manual de usuario

Kidde

Kidde P4010ACSCO-WF Manual de usuario

Kidde

Kidde K10LLCO Manual de usuario

Kidde

Kidde Fyrnetics 423D/9HIR Manual de usuario

Kidde

Kidde KN-COB-DP-H) Manual de usuario

Kidde

Kidde KN-COPP-B Manual de usuario

Kidde

Kidde KN-COB-LP2 Manual de usuario

Kidde

Kidde K10SCO Manual de usuario

Kidde

Kidde KN-COB-B Manual de usuario

Kidde

Kidde K7CO Instrucciones de uso

Kidde

Kidde KN-COB-B-LS Manual de usuario

Kidde

Kidde KN-COB-DP-H) Manual de usuario

Kidde

Kidde KN-COP-DP-10YLCA Manual de usuario

Kidde

Kidde C3010-CA Manual de usuario

Kidde

Kidde Fyrnetics 423/9HIR Instrucciones de montaje

Kidde

Kidde KN-COB-B-LPM Manual de usuario

Kidde

Kidde KN-OOB-B Manual de usuario

Kidde

Kidde 9CO5 Manual de usuario

Kidde

Kidde KN-COPE-I Manual de usuario

Kidde

Kidde KN-COPP-3 Manual de usuario

Kidde

Kidde CO120X Manual de usuario

Kidde

Kidde K5CO Manual de usuario

Kidde

Kidde KIR-PHCD Instrucciones de montaje

Kidde

Kidde SL177i Manual de usuario

Manuales populares de Alarma de monóxido de carbono de otras marcas

Honeywell

Honeywell H450EN Manual de usuario

First Alert

First Alert FCD2B Manual de usuario

Honeywell

Honeywell SF350RVUL Manual de usuario

Poolguard

Poolguard DAPT-2 Manual de usuario

Ei Electronics

Ei Electronics Ei 261D Manual

Bacharach

Bacharach Model 105 Manual

Firex

Firex COZ-1 Manual de usuario

Costar

Costar 12RV-D Manual de usuario

First Alert

First Alert CO410 Manual de usuario

FireAngel

FireAngel CO-9X Manual de usuario

Costar

Costar 12-24SIR Manual de usuario

System Sensor

System Sensor CO1224T Manual de usuario

Deltronic Security

Deltronic Security CN-1231 Manual de usuario

GE Interlogix

GE Interlogix 240 COE - Carbon Monoxide Alarm Manual de usuario

Sygonix

Sygonix 2377794 Manual de usuario

Convoy Tech

Convoy Tech CO311 Manual de usuario

nest

nest PROTECT Manual de usuario

Bosch

Bosch CRS-WLCD-TA869 Manual de usuario