Kidde K7CO Instrucciones de uso

User and Installer Guide

Battery Carbon Monoxide Alarms

Quick Start Instructions

included at the back of

this User Guide

Alarm

Move to

Fresh Air

Operate

Model: K7CO

Carbon Monoxide Alarm

Fault

Alarm

Move to

Fresh Air

Operate

Model: K7DCO

Fault

Carbon Monoxide Alarm

PPM of CO displayed

Lb= Low Battery

End= End of Unit Life

Model: K7CO

Model: K7DCO

BS EN50291-1: 2018

BS EN50291-2: 2019

LICENSE NO. KM 738897

P/N: K7CO-7201-01

Thank You for Purchasing this Kidde Alarm

function to temporarily silence nuisance alarms.

Teach children how to respond to the alarm and that they should never play with the unit. This alarm is

designed to detect carbon monoxide from any source of combustion in a residential environment. As well as

being recommended for use in homes, this alarm is approved for use in caravans, motor homes and boats.

NOTE: Please thoroughly read this user guide and save the document for future reference and to pass on

to any subsequent owner.

IMPORTANT: Additional markings can be found on the back of the unit.

The manufacturer recommends replacing this alarm ten years from the install date on the side of alarm.

Model: ______________________________

Date Code (on side): ____________________

Date of Purchase: ______________________

Where Purchased: ______________________

Date to Replace: ________________________

Product Support: 0800 917 0722

Please write down the below information

and have this at hand when you call.

ENVIRONMENTAL PROTECTION

Waste electrical products should not be disposed of with household

waste. Please recycle where facilities exist. Check with Local Authority

or Supplier for recycling advice.

Model: ______________________________

Date Code (on side): ____________________

Date of Purchase: ______________________

Where Purchased: ______________________

Date to Replace: ________________________

Contents

1. Carbon Monoxide Alarm: What To Do When the Alarm Sounds.................................................................................... 4

2. Other Alarm Visual and Audible Indicators.................................................................................................................................... 5

3. Troubleshooting Guide.............................................................................................................................................................................. 6

4. Introduction, Product Features and Specifications.................................................................................................................. 7

5. Limitations of CO Alarms...........................................................................................................................................................................9

6. Recommended Locations for Alarms..............................................................................................................................................10

7. Locations to Avoid.......................................................................................................................................................................................11

8. Installation.........................................................................................................................................................................................................13

9. Operation and Testing............................................................................................................................................................................. 14

10. Recognizing Nuisance Alarms............................................................................................................................................................. 15

11. Battery ................................................................................................................................................................................................................ 16

12. General Carbon Monoxide (CO) Information............................................................................................................................. 17

13. Cleaning Your Alarm.................................................................................................................................................................................. 19

14. Service and Warranty................................................................................................................................................................................. 21

Quick Start Instructions ..........................................................................................................................................................................22

1. Carbon Monoxide Alarm: What To Do When the Alarm Sounds

The carbon monoxide (CO) alarm pattern is four quick beeps repeating every 5 seconds. The red LED blinks in sync

with the beep pattern. The digital display on model K7DCO will show the PPM level of CO detected.

WARNING: CARBON MONOXIDE ALARM ACTIVATION INDICATES THE PRESENCE OF CARBON

MONOXI O AT HIGH CONCENTRATIONS WHICH CAN KILL YOU.

Based on recommendations from EN 50292, follow these steps if alarm sounds:

1. Keep calm and open all doors and windows. Turn off all fuel-burning appliances if possible. Note: it is possible

that outdoor conditions could influence domestic CO alarms (bad traffic pollution in cold weather, for

example). In these circumstances, the level of indoor CO might actually increase when doors and windows

are opened.

2. If the alarm continues to sound, even after being reset (where appropriate), then evacuate the premises,

alerting other occupants to the risk. Leave doors and windows open. Do not re-enter the premises.

3. Get medical help for anyone suffering the effects of CO poisoning, and advise that CO inhalation is suspected.

4. Call Gas Emergency Services: 0800 111 999, or your local Gas Safe Registered Engineer:

PHONE NUMBER:

Never restart the source of the CO problem until it has been corrected.

Never ignore the sound of the alarm!

NOTE: See Section RECOGNIZING NUISANCE ALARMS, for nuisance alarm situations.

2. Other Alarm Visual and Audible Indicators

Operational Mode Visual Indications Audible Indications Action/Note:

Normal (standby) Green LED blinks approx every

30 sec.

Test (button press when

no alarm condition is

present) Red LED blinks in sync with beep

pattern.

Model K7DCO digital display will

show 3 dashes and then “888”.

4 loud pulses, a pause,

4 loud pulses.

Single beep

Perform test button press

once a week to verify proper

alarm operation.

CO Alarm Memory (unit

has experienced a CO

alarm event or 100 ppm

or more CO within the

last 14 days)

Red LED blinks every 60 sec. None. Model K7CO: Push button to

clear Alarm Memory.

Model K7DCO: Push Test/

Reset while the Peak Level

button is depressed to clear

Alarm Memory.

Peak Level CO

K7DCO only

Digital display shows the highest

CO reading between 11 and 999

ppm since the peak level was

reset.*

None. Push test/reset button while

peak level button is depressed

to clear peak level memory.

CO alarm reset Red LED continues to signal the

alarm pattern.

After button push: CO

alarm pattern stops. present or if it experienced a

nuisance situation. Re-alarm

means danger. Move to fresh

air and call 0800 111 999.

* NOTE: CO levels up to 30ppm can occur under normal non-dangerous conditions. Such conditions could include

Green and amber LEDs illuminate.

3. Troubleshooting Guide

NOTE: If at any time your alarm fails to operate correctly (erratic or low sound, for example), or if you require further

information, please contact customer support at 0800 917 0722.

Trouble Condition Visual Indications Audible Indications Action:

Low Battery Amber LED blinks every

60 sec.

Model K7DCO digital

display will show “Lb”.

Chirp every 60 sec. * Push test button once to silence for 24 hrs.

Note: 30 days after Low Battery begins, the

* Replace batteries as soon as possible.

Fault Mode Amber LED blinks every

30 sec.

Model K7DCO digital

display will show “Err”.

Chirp every 30 sec. * See Cleaning Your Alarm section.

* Push test button once to attempt to reset

the unit.

End of Unit Life Amber LED blinks twice

every 60 sec.

Model K7DCO digital

display will show “End”.

Two chirps every

60 sec.

* Push button once to silence for 24 hrs.

Note: 30 days after End of Unit Life begins, the

* Remove, dispose unit, and replace as soon

as possible.

MCU FailureNone. Constant tone. * Replace alarm.

Stuck Button Amber LED blinks

every 5 sec.

Chirp every 5 sec. * Push button to dislodge it from being stuck.

If button cannot be unstuck, remove, dispose

unit, and replace as soon as possible.

3. Troubleshooting Guide

4. Introduction, Product Features and Specifications

Introduction

This alarm detects carbon monoxide using an electrochemical cell. Many times throughout this User Guide,

we will refer to Carbon Monoxide as “CO.”

Ten (10) years after the unit was installed, this unit will automatically alert you that it is time to replace the unit.

This is called “End of Unit Life” mode. See Troubleshooting Guide. To help track the life of your alarm, write the

installation date in the space provided on the side of the alarm. A label has been provided that has important

information on what to do in case of a CO alarm. Place the label at eye level on a wall near the alarm after it is

mounted.

Product Features and Specifications:

Temperature Operating Range: -10°C to 45°C

Humidity Operating Range: up to 90% RH non-condensing

Audible Alarm: 85+ dB(A) at 3 m, 3.0 to 3.5 kHz pulsing alarm

Digital Display (K7DCO only)

NOTE: Depending on the ambient condition (temperature, humidity) and the condition of the sensor,

the display readings may vary. The digital readings tolerances are 0-999 +/- 30% +15ppm during these con-

ditions: Ambient: 27°C ± 12°C (80°F ± 10°F), atmospheric pressure ±10%, 40% ± 3% relative humidity

CO Sensor: Electrochemical

Peak Level Memory (K7DCO only)

CO Alarm Reset

Storage and Transport Conditions: -20° C to +60° C, 5-95%RH (non-condensing)

Approved for use in homes, caravans, motor homes and boats.

Product Features

Gr een,

Pow er LED

Red,

Ala rm LED

Test / Reset

Button

Model: K7CO

Alarm

Move to

Fresh Air

Operate Fault

Carbon Monoxide Alarm

PPM of CO displayed

Lb= Low Battery

End= End of Unit Life

Gr e Amber,

Fault LED

Amber,

Fault LED

en,

Pow er LED

Red,

Ala rm LED

Test / Reset

Button

Peak Level Button Digital Display

with digital display

Model: K7DCO

Alarm

Move to

Fresh Air

Operate

Carbon Monoxide Alarm

Fault

5. Limitations of CO Alarms

WARNING: PLEASE READ CAREFULLY AND THOROUGHLY

This alarm is not intended to alert hearing impaired individuals.

LIMITATIONS OF CO ALARMS

IMPORTANT: This alarm is designed to detect carbon monoxide gas from ANY source of combustion. It is

NOT designed to detect any other gas.

CAUTION: This alarm will only indicate the presence of carbon monoxide gas at the sensor. Carbon

monoxide gas may be present in other areas. Never restart the source of a CO problem until it has been

fixed. NEVER IGNORE THE ALARM!

WARNING: THIS PRODUCT IS INTENDED FOR USE IN ORDINARY INDOOR LOCATIONS OF

FAMILY LIVING UNITS. IT IS NOT DESIGNED TO MEASURE COMPLIANCE WITH COMMERCIAL

AND INDUSTRIAL STANDARDS. THIS ALARM IS NOT SUITABLE FOR INSTALLATION IN HAZARD

OUS LOCATIONS.

IMPORTANT: THIS CARBON MONOXIDE ALARM IS DESIGNED TO DETECT CARBON MONOXIDE

FROM ANY SOURCE OF COMBUSTION INCLUDING IMPROPER OR MALFUNCTIONING APPLIANC

ES. THE INSTALLATION OF THIS DEVICE SHOULD NOT BE USED AS A SUBSTITUTE FOR PROPER

INSTALLATION, USE AND MAINTENANCE OF FUEL BURNING APPLIANCES INCLUDING APPRO

PRIATE VENTILATION AND EXHAUST SYSTEMS.

This alarm does not prevent CO from occurring, nor can it solve any existing CO problem.

WARNING: THIS DEVICE IS DESIGNED TO PROTECT INDIVIDUALS FROM ACUTE EFFECTS OF

CARBON MONOXIDE EXPOSURE. IT WILL NOT FULLY SAFEGUARD INDIVIDUALS WITH SPECIFIC

MEDICAL CONDITIONS. IF IN DOUBT, CONSULT A MEDICAL PRACTITIONER. INDIVIDUALS WITH

MEDICAL PROBLEMS MAY CONSIDER USING WARNING DEVICES WHICH PROVIDE AUDIBLE AND

VISUAL SIGNALS FOR CARBON MONOXIDE CONCENTRATIONS UNDER 30 PPM.

This alarm has not been investigated for carbon monoxide detection below 50 PPM.

This alarm requires a continuous supply of electrical power – it will not work without power.

WARNING: THIS CARBON MONOXIDE ALARM IS NOT A SUBSTITUTE FOR INSTALLING AND

MAINTAINING AN APPROPRIATE NUMBER OF SMOKE ALARMS IN YOUR HOME. THIS ALARM

WILL NOT SENSE SMOKE, FIRE, OR ANY POISONOUS GAS OTHER THAN CARBON MONOXIDE.

FOR THIS REASON YOU MUST INSTALL SMOKE ALARMS TO PROVIDE EARLY WARNING OF FIRE

AND TO PROTECT YOU AND YOUR FAMILY FROM FIRE AND ITS RELATED HAZARDS.

6. Recommended Locations for CO Alarms

NOTE: Note: CO alarms should be installed following the guidance of relevant local standards, such as

EN 50292.

Whether the alarm is wall-mounted or ceiling mounted, place the alarm a horizontal distance of between

1 metre and 3 metres from a fuel burning appliance.

When mounting the alarm on the wall, use an inside wall with the top edge of the alarm at a minimum

of 150 mm below the ceiling. The bottom of the alarm should also be at a level greater than the height

of any door or window.

Locate within hearing distance of bedrooms* and place at sleeping height if a heating appliance is in the

bedroom.

CO alarms in rooms with sloped ceilings should be located on the high side of the room.

Ceiling mounted alarms should be at least 300 mm from any wall.

If there is a partition in the room, locate the alarm on the same side of the partition as the potential source.

* A CO alarm should be installed in all rooms containing a fuel burning appliance. Additional CO alarms

should be installed in rooms where most awake time is spent, in every sleeping area, and on every level of

the home.

Otros manuales para K7CO

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Alarma de monóxido de carbono de Kidde

Kidde

Kidde K10LLCO Manual de programación

Kidde

Kidde 9CO5-LP Manual de usuario

Kidde

Kidde P3010K-CO Manual de usuario

Kidde

Kidde KN-COB-B-LS Manual de usuario

Kidde

Kidde KN-COB-IC Manual de usuario

Kidde

Kidde Fyrnetics 423/9HIR Instrucciones de montaje

Kidde

Kidde KN-COB-B Manual de usuario

Kidde

Kidde CO120X Manual de usuario

Kidde

Kidde Fyrnetics 423D/9HIR Manual de usuario

Kidde

Kidde KN-COB-DP-H) Manual de usuario

Kidde

Kidde KN-COSM-ICA Manual de usuario

Kidde

Kidde KN-COSM-IBA Manual de usuario

Kidde

Kidde KN-COB-ICB-CA Manual de usuario

Kidde

Kidde KN-COB-B-LPM Manual de usuario

Kidde

Kidde KN-COPP-3 Manual de usuario

Kidde

Kidde C3010 Manual de usuario

Kidde

Kidde K10SCO Manual de usuario

Kidde

Kidde P4010ACSCO-WF Manual de usuario

Kidde

Kidde KN-COEG-3 (900-01 13) Manual de usuario

Kidde

Kidde KIR-HCD Instrucciones de montaje

Kidde

Kidde 900-0259 Manual de usuario

Kidde

Kidde KN-COB-B-LS Manual de usuario

Kidde

Kidde SL177i Manual de usuario

Kidde

Kidde KN-COPP-3 Manual de usuario

Manuales populares de Alarma de monóxido de carbono de otras marcas

Honeywell

Honeywell H450EN Manual de usuario

First Alert

First Alert FCD2B Manual de usuario

Honeywell

Honeywell SF350RVUL Manual de usuario

Poolguard

Poolguard DAPT-2 Manual de usuario

Ei Electronics

Ei Electronics Ei 261D Manual

Bacharach

Bacharach Model 105 Manual

Firex

Firex COZ-1 Manual de usuario

Costar

Costar 12RV-D Manual de usuario

First Alert

First Alert CO410 Manual de usuario

FireAngel

FireAngel CO-9X Manual de usuario

Costar

Costar 12-24SIR Manual de usuario

System Sensor

System Sensor CO1224T Manual de usuario

Deltronic Security

Deltronic Security CN-1231 Manual de usuario

GE Interlogix

GE Interlogix 240 COE - Carbon Monoxide Alarm Manual de usuario

Sygonix

Sygonix 2377794 Manual de usuario

Convoy Tech

Convoy Tech CO311 Manual de usuario

nest

nest PROTECT Manual de usuario

Bosch

Bosch CRS-WLCD-TA869 Manual de usuario