KFI AMP-25 Manual

Model #AMP-25-R2
Owner’s Manual and Operating Instructions
2500 lb.
ATV/UTV WINCH
Revision Date 2019-10-21


5AMP-25-R2
Table of Contents
Introduction��������������������������������������������������������������������������������� 1
Accessories �������������������������������������������������������������������������������������������������������1
This Booklet �����������������������������������������������������������������������������������������������������1
Introduction��������������������������������������������������������������������������������� 1
ManualConventions������������������������������������������������������������������� 2
SafetyRules���������������������������������������������������������������������������������� 3
ControlsandFeatures����������������������������������������������������������������� 5
Winch ���������������������������������������������������������������������������������������������������������������5
Installation������������������������������������������������������������������������������������ 6
Step 1-ATV Install Preparation ������������������������������������������������������������������������6
Step 2-Winch Assembly Preparation ����������������������������������������������������������������7
Step 3-Install Winch Assembly �����������������������������������������������������������������������8
Step 4-Handlebar Remote Install ����������������������������������������������������������������������9
Step 5-Reinstall ������������������������������������������������������������������������������������������������9
Operation������������������������������������������������������������������������������������ 10
General Tips for Safe Operation ���������������������������������������������������������������������10
Self Recovery �������������������������������������������������������������������������������������������������10
Winching Techniques ������������������������������������������������������������������������������������11
Maintenance������������������������������������������������������������������������������� 12
Motor ��������������������������������������������������������������������������������������������������������������12
Lubrication �����������������������������������������������������������������������������������������������������12
Cable Assembly Replacement ������������������������������������������������������������������������12
AMP-25-R2Specifications������������������������������������������������������� 13
Performance Specifications ����������������������������������������������������������������������������13
Model Winch Diagram �����������������������������������������������������������������������������������14
Winch Parts List ���������������������������������������������������������������������������������������������15
Troubleshooting������������������������������������������������������������������������� 16
PlowingAlert������������������������������������������������������������������������������ 16
Warranty������������������������������������������������������������������������������������ 17
Warranty Qualifications ���������������������������������������������������������������������������������17
Repair/Replacement Warranty �����������������������������������������������������������������������17
Do not return the unit to the place of purchase ����������������������������������������������17
Warranty Exclusions ��������������������������������������������������������������������������������������17
Normal Wear �����������������������������������������������������������������������������������������������17
Installation, Use and Maintenance �����������������������������������������������������������������17
Other Exclusions ��������������������������������������������������������������������������������������������17
Limits of Implied Warranty and Consequential Damage �������������������������������17
Contact Information ����������������������������������������������������������������������������������������18
Address �����������������������������������������������������������������������������������������������������������18
Corporate: �������������������������������������������������������������������������������������������������������18
Customer Service ��������������������������������������������������������������������������������������������18
Technical Service �������������������������������������������������������������������������������������������18
Agreement ������������������������������������������������������������������������������������������������������18
Notes������������������������������������������������������������������������������������������� 19


1
AMP-25-R2
Introduction
Introduction
Congratulations on your purchase of a KFI winch.
KFI researches and develops winches to strict
specications. With proper use and maintenance,
this winch will bring years of satisfying service.
Accessories
Kappers Fabricating Inc. manufactures,
purchases and sells accessories designed to
help you get the most from your purchase. To nd
out more about our products visit our web site at
www.kproducts.com
Record the model as well as date and place of purchase for future reference. Have this information
available when ordering parts and when making technical or warranty inquiries.
This Booklet
Every effort has been made to ensure the
accuracy and completeness of the information in
this manual. We reserve the right to change, alter
and/or improve the product and this document at
any time without prior notice.
Kappers Fabricating Inc� Support
1-877-346-2050
Model Number
AMP-25-R2
Date of Purchase
Purchase Location
Serial Number

2AMP-25-R2
CAUTION used without the safety alert symbol
indicates a potentially hazardous situation
which, if not avoided, may result in property
damage.
CAUTION indicates a potentially hazardous
situation which, if not avoided, may result in
minor or moderate injury.
WARNING indicates a potentially hazardous
situation which, if not avoided, could result in
death or serious injury.
DANGER indicates an imminently hazardous
situation which, if not avoided, will result in
death or serious injury.
Manual Conventions
This manual uses the following symbols to
help differentiate between different kinds of
information. The safety symbol is used with a key
word to alert you to potential hazards in operating
and owning a winch.
Follow all safety messages to avoid or reduce the
risk of serious injury or death.
Manual Conventions
DANGER
NOTE
If you have questions regarding your winch,
we can help. Please call our help line at
1-877-346-2050.
WARNING
CAUTION
CAUTION

3
AMP-25-R2
Manual Conventions
Safety Rules
Do not use this winch for lifting or moving
people or animals.
DANGER
Read this manual thoroughly before operating
your winch. Failure to follow instructions could
result in serious injury or death.
WARNING
Do not move the vehicle to pull a load (towing)
on the winch cable. This could result in cable
breakage.
WARNING
Pull only on areas of the vehicle as specied
by the vehicle manufacturer.
WARNING
Do not exceed the rated capacity.
WARNING
Keep yourself and others a safe distance from
the side of the cable when under tension.
WARNING
Never step over a cable or near a cable under
load.
WARNING
The cable may break before the motor stalls.
For heavy loads at or near rated capacity, use
a pulley block/snatch block to reduce the load
on the wire rope.
WARNING
Do not use the winch to secure or hold a
vehicle for a long period of time. Do not use
the winch to secure a vehicle for transport.
WARNING
Disconnect the remote control and battery
leads when not in use for extended periods.
WARNING
Avoid “shock loads” by using the control switch
intermittently to take up the slack in the wire
rope. “Shock loads” can far exceed the rate
capacity for the cable and drum.
Do not accelerate your vehicle while winching.
Loss of traction can cause a shock load on the
cable. Do not use cable as a pull strap.
WARNING

4AMP-25-R2
Do not use as a hoist. Do not use for overhead
lifting.
Safety Rules
WARNING
Batteries contain acid and produce explosive
gases.
Keep sparks, ames and cigarettes away from
batteries at all times. Wear safety glasses and
protect the eyes at all times. Do not lean over
the batteries during operation.
WARNING
When re-spooling the cable, ensure that the
cable spools in the under-wind position with
the cable entering the drum from the bottom,
not the top.
To re-spool correctly, and while wearing
gloves, keep a slight load on the cable while
pushing the remote button to draw in the
cable. Walk toward the winch not allowing the
cable to slide through your hands. Do not let
your hands get within 12” of the winch while
re-spooling. Turn off the winch and repeat
the procedure until a few feet of cable is left.
Disconnect the remote control and nish
spooling by rotating the drum by hand with
the clutch disengaged. Keep hands clear of
the fairlead and drum while the winch is under
power.
WARNING
Duration of winching pulls should be kept as
short as possible.
If the motor becomes uncomfortably hot to
the touch, stop winching immediately and let
it cool down for a few minutes. Do not pull for
more than one minute at or near the rated
load.
CAUTION
Apply blocks to the wheels of the vehicle when
on an incline.
CAUTION
Do not wrap the cable around any object and
hook it back onto itself.
CAUTION
Use gloves to protect hands when handling the
cable. Never let the cable slide through your
hands.
CAUTION
If the motor stalls, do not maintain power to
the winch.
Electric winches are designed and made for
intermittent use and should not be used in
constant duty applications.
CAUTION
Never release the release clutch when there is
a load on the winch.
CAUTION
Use hook strap when handling the hook for
spooling or unspooling the cable.
CAUTION

5
AMP-25-R2
1
11
3
8
10
12
9
13
6
7
4
2
Controls and Features
Read this owner’s manual before operating your winch. Familiarize yourself with the location and
function of the controls and features. Save this manual for future reference.
Motor (1): 1.07 HP 12V DC motor provides power
to the planetary gear mechanism.
Winch Drum (2): The winch drum is the cylinder
on which the cable is stored. It can feed or wind
the rope depending on the remote winch switch.
Steel Cable (3): 3/16” x 45.9’ Steel cable designed
specically for load capacity of 2,500lbs. (44 use-
able feet with ve wraps on the drum). The steel
cable feeds onto the drum in the “under wind” po-
sition through the roller fairlead (4) and is looped
at the end to accept the clevis hook pin (11).
Roller Fairlead (4): When using the winch at an
angle the roller fairlead acts to guide the steel
cable onto the drum and minimizes damage to the
steel cable from abrasion on the winch mount or
bumper.
Free spooling Clutch (5): The clutch allows the
operator to manually disengage (“RELEASE”) the
spooling drum from the gear train. Engaging the
clutch (“ENGAGE”) locks the winch into the gear
system.
Braking System (6): Braking action is
automatically applied to the winch drum when the
winch motor is stopped and there is a load on the
steel cable.
Planetary Gear System (7): The reduction gears
convert the winch motor power into extreme
pulling forces. This system allows high torque
while maintaining compact size and light weight.
Clamshell Plug & Play Mini-Rocker Switch
(8): Handlebar mounted switch for easy access.
Plugs directly into factory harness
Model Specic Winch Mount (9): Winch mount
designed specically for select ATVs.
Contactor (10): Power from the vehicle battery
ows through the weather sealed solenoid switch
before being directed to the winch motor.
Clevis Hook (11): Provides a means for
connecting the looped ends of cables to an
anchor.
Cable Hook Stopper (12): Protects the Rollers,
motor and gears.
Wires (13): Model Specic Pre-installed Wires
Winch
5

6AMP-25-R2
This KFI 2,500 lb Plug & Play winch assembly is
designed to be a direct t up to the specic ATV
Models from our online application chart.
1. On the 850 and 1000 Models remove the
front rack to gain access to the battery.
Disconnect the battery.
2. On the ETX, 450 and 570, open the front
rack and remove the center cover [A] by
removing the (4) Torx fasteners. You will
also need to lightly pull the rubber seal out
of the groove around the center cover to be
removed as shown in Figure 1.
3. Remove any added on bumpers or brush
guards.
4. Remove the lower cowling [B] on the
Sportsman models and the bumper [C] and
front assembly clip [D] on the Scramblers as
shown in Figure 2-5.
5. Remove and discard the Winch pocket
cover [E] shown in Figure 2-5.
6. Remove the winch assembly from the box
and cut the zip tie that is holding the power
wires for packaging.
Step 1-ATV Install Preparation
Installation
Before you start to install this winch,
disconnect the vehicle ground and positive
leads from the battery. (ETX, 450 and 570
battery is located lower front frame and the
850 and 1000 is located under the front rack
WARNING
Installation
“Figure 2”
ETX, 450 and 570
“Figure 3”
Scrambler
“Figure 4”
850 Sportsman “Figure 5”
850 & 1000 Sportsman
“Figure 1” A
B
B
C
D
B
E
E
E
E
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Cabrestante de KFI
































