Keysight U1610/20A Manual de usuario
Keysight U1610/20A
Handheld Digital
Oscilloscope
Quick Start
Guide
Contacting Keysight
www.keysight.com/find/assist
(worldwide contact information for
repair and service)
Safety and EMC Information
This handheld scope is certified to
the following safety and EMC
requirements.
– IEC 61010-1/EN 61010-1, IEC
61010-2-033/EN 61010-2-033
– Canada: CAN/CSA-C22.2
No. 61010-1, CAN/CSA-C22.2
No. 61010-2-033
– USA: ANSI/UL Std. No. 61010-1,
ANSI/UL Std. No. 61010-2-033
– IEC 61326-1/EN 61326-1
– Australia/New Zealand: AS/NZS
CISPR 11
– Canada: ICES/NMB-001
Use with compatible test probe/
leads.
Safety Notices
CAUTION
A CAUTION notice denotes a
hazard. It calls attention to an
operating procedure, practice, or
the like that, if not correctly
performed or adhered to, could
result in damage to the product or
loss of important data. Do not
proceed beyond a CAUTION notice
until the indicated conditions are
fully understood and met.
WARNING
A WARNING notice denotes a
hazard. It calls attention to an
operating procedure, practice, or
the like that, if not correctly
performed or adhered to, could
result in personal injury or
death. Do not proceed beyond a
WARNING notice until the
indicated conditions are fully
understood and met.
Safety symbols
Direct current (DC)
Alternating current (AC)
Both direct and alternating
current
Earth (ground) terminal
Caution, risk of danger
(refer to the instrument
manual for specific Warning
or Caution information)
Equipment protected
throughout by double
insulation or reinforced
insulation
Caution, risk of electric
shock
CAT II Category II overvoltage
protection
CAT III Category III overvoltage
protection
2 Keysight U1610/20A Quick Start Guide
For further safety information details, refer to the
Keysight U1610/20A Handheld Digital Oscilloscope User’s Guide.
ENGLISH
Keysight U1610/20A Quick Start Guide 3
ENGLISH
Verify that you received the following items in the
shipment of your handheld scope:
4Power cable
4Li-Ion battery pack, 10.8 V (included in the
handheld scope)
4AC/DC adapter
410:1 CAT III 600 V scope probe
4BNC-to-probe adapter
4DMM (digital multimeter) test lead kit
4USB cable
4
Hand strap (attached on the handheld scope)
4Neck strap
4Certificate of Calibration
If anything is missing or damaged, contact the
nearest Keysight Sales Office.
NOTE All related documents and software are available for
download at www.keysight.com/find/hhTechLib.
4 Keysight U1610/20A Quick Start Guide
ENGLISH
Charge the Battery
Before using the handheld scope for the first time
or after a prolonged storage period, fully charge
the battery for at least 3 hours, with the handheld
scope turned off, using the AC/DC adapter
provided. If the battery is fully discharged after
subsequent use, charge the battery with the
handheld scope turned on.
The power key will turn constant yellow when
the battery is fully charged.
Keysight U1610/20A Quick Start Guide 5
ENGLISH
Power On the Handheld Scope
Press and hold for approximately 3 seconds.
When the handheld scope display appears, the
handheld scope is ready for use.
NOTE Hook up all cables and accessories before applying
power. You can connect/disconnect probes while
the handheld scope is turned on.
6 Keysight U1610/20A Quick Start Guide
ENGLISH
Product Outlook
Scope terminals
Display screen
Function softkeys
To perform the
function displayed
above each softkey.
Acquisition and
function controls
To access the scope,
meter, logger,
system, and help
functions.
Vertical controls
To set the
vertical scaling
(volt/div) and
vertical offset.
Power key
USB interface
connectorand
DC power
inlet
Directional keys
Horizontal controls
To control the sweep speed
(sec/div) and horizontal position
of the waveform. Use
to zoom into the waveform.
Meter terminals
Keysight U1610/20A Quick Start Guide 7
ENGLISH
Oscilloscope Display
Multimeter Display
6
4
1 5
7
8
3
2
6
4
10
9
11
12
13
8 Keysight U1610/20A Quick Start Guide
ENGLISH
Logger Display
1Displays the channel and timebase setup
information.
2Displays the channel input waveforms.
3Displays the sample rate.
4Displays the key/softkey function menus.
5Displays the signal acquisition mode.
6Displays the battery status and AC
connectivity for battery charging.
7Displays the signal triggering status.
8Displays the date and time.
9Displays the acquisition, start date and time,
and duration status.
10 Displays the measurement.
11 Displays the virtual measurement scale.
12 Displays the average, maximum, and
minimum values.
13 Indicates the auto or manual ranging mode.
14 Displays the logging graph.
6
9
10
1
4
4
12
Keysight U1610/20A Quick Start Guide 9
ENGLISH
Set the Date and Time
Press > > . Press
any softkey and use the or key to change
the values.
Set the Language
Press > > and use
the keys to select the language.
Press again to exit the selection menu.
Reset the Oscilloscope
Press > .
NOTE is only accessible when in the Scope
mode.
NOTE Before resetting to factory default settings, you may
want to save the current handheld scope
configuration for later use by pressing >
.
NOTE For details on using the oscilloscope functions, see
the User’s Guide.
10 Keysight U1610/20A Quick Start Guide
ENGLISH
Data Logging
The data logger acts as a recorder to log and plot
input signal trends for both scope and meter
measurements.
To access the logger mode, press .
Connect Probes to Oscilloscope Terminals
NOTE For details on using the logger functions, see the
User’s Guide.
Tabla de contenidos
Idiomas:
Otros manuales de Equipo de prueba de Keysight
Keysight
Keysight 10070D Manual de usuario
Keysight
Keysight 16092A Manual de operación
Keysight
Keysight DSO1000B Series Manual técnico
Keysight
Keysight N2771B Manual de usuario
Keysight
Keysight U1610A Manual de usuario
Keysight
Keysight N1930 B Series Manual de usuario
Keysight
Keysight 90000 X Series Manual de usuario
Keysight
Keysight U1452AT Manual de usuario
Keysight
Keysight InfiniiVision DSOX1204A Manual de usuario
Keysight
Keysight U1731C Manual de usuario
Keysight
Keysight E6650A EXF Manual del propietario
Keysight
Keysight M8000 Series Manual de usuario
Keysight
Keysight N443xD Manual de usuario
Keysight
Keysight N5245-60125 Guía de inicio rápido
Keysight
Keysight Infiniium S Series Manual de usuario
Keysight
Keysight M9380A Guía del usuario
Keysight
Keysight 85053A Manual
Keysight
Keysight U1452A Manual de usuario
Keysight
Keysight 85132E Hoja de especificaciones
Keysight
Keysight N5281A Manual
Manuales populares de Equipo de prueba de otras marcas
SMART
SMART KANAAD SBT XTREME 3G Series Manual de usuario
Agilent Technologies
Agilent Technologies BERT Serial Manual de usuario
Agilent Technologies
Agilent Technologies N3280A Manual de usuario
Vernier
Vernier Go Direct Voltage Manual de usuario
Lifeloc
Lifeloc R.A.D.A.R. Manual de usuario
Fluke
Fluke T5-600 Instrucciones de funcionamiento e instalación
