Keysight 16117C Manual de operación

Keysight 16117C

Low Noise Test Lead

Operation and

Service Manual

Notice

The information contained in this document is subject to change without notice

This document contains proprietary information which is protected by copyright. All rights are

reserved. No part of this document may be photocopied, reproduced, or translated to another

language without the prior written consent of the Agilent T

echnologies.

Agilent T

echnologies Japan, Ltd.

Component T

est PGU-Kobe

1-3-2, Murotani, Nishi-ku, Kobe-shi,

Hyogo

,651-2241 Japan

arranty

This Agilent T

echnologies instrument product is warranted against defects in material and

workmanship for aperiod of one year from the date of shipment, except that in the case of

certain components listed in this manual, the warranty shall be for the specied period. During

the warranty period, Agilent T

echnologies will, at its option, either repair or replace products

which prove to be defective

or warranty service or repair

,this product must be returned to aservice facility designed by

Agilent T

echnologies

.The Buyer shall prepay shipping charges to Agilent T

echnologies and

Agilent T

echnologies shall pay shipping charges to return the product to the Buyer

.However

the Buyer shall pay all shipping charges

,duties

,and taxes for products returned to Agilent

echnologies from another country

Agilent T

echnologies warrants that its software and rmware designed by Agilent T

echnologies

for use with an instrument will execute its programming instruction when property installed on

that instrument. Agilent T

echnologies does not warrant that the operation of the instrument,

or software

,or rmware will be uninterrupted or error free

Limitation of W

arranty

The foregoing warranty shall not apply to defects resulting from improper or inadequate

maintenance by the Buyer, Buyer-supplied software or interfacing, unauthorized modication

or misuse, operation outside of the environmental specications for the product, or improper

site preparation or maintenance

No other warranty is expressed or implied. A

gilent T

echnologies specically disclaims the

implied warranties of merchantability and tness for a particular purpose

Certication

The Agilent T

echnologies certies that this product met its published specications at the

time of shipment from the factory

. Agilent T

echnologies further certies that its calibration

measurements are traceable to the United States National Institute of Standards and

Technology, to the extent allowed by the Institute's calibration facility, or to the calibration

facilities of other International Standards Organization members.

Exclusive Remedies

The remedies provided herein are the buyer's sole and exclusive remedies. Agilent Technologies

shall not be liable for any direct, indirect, special, incidental, or consequential damages,

whether based on contract, tort, or any other legal theory

Assistance

Product maintenance agreements and other customer assistance agreements are available for

Agilent Technologies products.

If you need assistance, contact your nearest Agilent T

echnologies Sales and Service Oce

ddresses are provided at the back of this manual.



Manual Printing History

The manual printing date and part number indicate its current edition. The printing date

changes when anew edition is printed. (Minor corrections and updates which are incorporated

at reprint do not cause the date to change.) The manual part number changes when extensive

technical changes are incorporated.

December 1991

::::::

::::::::::::::::::::: ::::

::::::::::::::::::::: :: :: :::::::::

First Edition

ebruary 1999

:::::::

::::::::::::::::::::::: ::::::::::::::::::::::: :: :: :::::::::

Second Edition

July 1999

::::::::::

::::::::::::::::::::::: :: :::::::::

Third Edition (part number: 16117-90031)

May 2000

::::::::

::::::::::::::::::::: ::::

:::::

ourth Edition (part number: 16117-90031)

July 2001

:::::::::::::::::::::::

:::::::::::

Fifth Edition (part number: 16117-90041)

Safety Summary

The following general safety precautions must be observed during all phases of operation,

service

,and repair of this instrument. F

ailure to comply with these precautions or with specic

ARNINGS

elsewhere in this manual may impair the protection provided by the equipment.

In addition it violates safety standards of design, manufacture, and intended use of the

instrument.

The A

gilent T

echnologies assumes no liability for the customer's failure to comply with these

requirements

Note

16117C is designed for use in INST

ALLA

TION CA

TEGORY Iaccording to IEC

61010-1 and POLLUTION DEGREE 1according to IEC 61010-1 and IEC 60664-1.

16117C is an INDOOR USE product.

Do NOT operate in an Explosive Atmosphere

not

operate the instrument in the presence of ammable gasses or fumes

.Operation of any

electrical instrument in such an environment constitutes asafety hazard.

eep A

way from Live Circuits

Operating personnel must not remove instrument covers

.Component replacement and

internal adjustments must be made only by qualied maintenance personnel. Do not replace

components with the power cable connected. Under certain conditions

,dangerous voltages

may exist even with the power cable removed. T

oavoid injury

,always disconnect power and

discharge circuits before touching them.

Do NOT Service or Adjust While Alone

not

attempt internal service or adjustment unless another person, capable of turning o

power and capable of rendering rst aid and resuscitation, is present.

Do NOT Substitute Parts or Modify Instrument

Because of the danger of introducing additional hazards, do

not

substitute parts or perform

unauthorized modications to the instrument. Return the instrument to aAgilent

echnologies

Sales and Service Oce for service and repair to ensure the safety features are maintained.

Dangerous Procedure W

arnings

Warnings, such as the example below

, precede

POTENTIALLYD

ANGEROUS PROCEDURES

throughout this manual. Instructions contained in the

warnings

must be followed.

Warning

Dangerous voltages

, capable of causing death, are present in this

instrument. Use extreme caution when handling, testing, and adjusting

this instrument.

Safety Symbols

General denitions of safety symbols used on equipment or in manuals are listed below

Instruction manual symbol: the product is marked with this symbol when it is

necessary for the user to refer to the instruction manual.

Alternating current.

Direct current.

On (Supply).

O (Supply).

This

arning

sign denotes ahazard. It calls attention to aprocedure, practice,

condition or the like

,which, if not correctly performed or adhered to,could

result in injury or death to personnel.

This

Caution

sign denotes ahazard. It calls attention to a procedure

, practice

condition or the like

,which, if not correctly performed or adhered to,could

result in damage to or destruction of part or all of the product.

Note

denotes important information. It calls attention to a procedure

practice

,condition or the like, which is essential to highlight.

Axed to product containing static sensitive devices use anti-static handling

procedures to prevent electrostatic discharge damage to component.

Caution, risk of electric shock :T

erminals which may be supplied from the

interior of the equipment at avoltage exceeding 1kV

,or allow connection to a

voltage exceeding 1kV are marked with this symbol.

Contents

1. General Information

Introduction ....................

.........1-1

Using the 16117C ..................

......1-1

Product Description .....................

....1-1

Accessories Supplied ..................

.....1-1

Operating and Safety Precautions ................... .. .. 1-2

Service ................

............1-2

Specications ................

..........1-2

2. Preparation for Use

Introduction . .... .....................

...2-1

Initial Inspection ................... .. ..........2-1

Ambient Environmental Considerations .................. .. 2-3

Operating and Storage ..................

.......2-3

Connecting the A

dapter for Use ................. ......2-3

ackaging the A

dapter ................

..........2-4

3. Operation

Introduction .................................3-1

Making aCustom T

est Fixture ...........

.............3-2

Conguration ...............................3-2

Interlock Circuit ......... .....................3-3

Example Conguration of Custom T

est Fixture .... ............3-5

Checking Procedure ......... ....................3-6

4. Service

Introduction ..

....................... .. ....4-1

Replaceable Parts .. .. ...................

.4-1

Contents-1

Figures

2-1. Product Overview ....................

.....2-2

2-2. Floating DUT Measurement ................... .. .. .2-3

2-3. Grounded DUT Measurement ................... .. .. 2-4

3-1. A

dapter F

eatures ..................

.....3-1

3-2. Floating DUT Measurement Conguration .................. 3-2

3-3. Interlock cable Assignment (Wiring Side View) ............

.. 3-3

3-4. Example Conguration of Custom T

est Fixture ............. .. . 3-5

ables

1-1. Furnished A

ccessories ...... .....................1-1

2-1. Contents ......

......................... 2-2

3-1. Pin Assignment of Interlock Connector ...................3-3

3-2. ID Signal Condition .......................

.....3-4

4-1. Replaceable P

arts List ...........................4-1

Contents-2

Tabla de contenidos

Otros manuales de Equipo de prueba de Keysight

Keysight

Keysight U1452AT Manual de usuario

Keysight

Keysight E6607B Manual de usuario

Keysight

Keysight InfiniiVision 2000 X Series Manual de usuario

Keysight

Keysight N109228CA OIF CEI 3.1 Manual de usuario

Keysight

Keysight DSO1000B Series Manual técnico

Keysight

Keysight 1000B Series Manual de usuario

Keysight

Keysight 8516A Manual de servicio

Keysight

Keysight N5242-60124 Manual de usuario

Keysight

Keysight InfiniiVision 4000G X Series Manual de usuario

Keysight

Keysight DSOX3012T Manual de usuario

Keysight

Keysight 11636A Manual de servicio

Keysight

Keysight Infiniium 8000 Series Manual de usuario

Keysight

Keysight InfiniiVision M9241A Manual de usuario

Keysight

Keysight Infiniium 90000A Series Manual de usuario

Keysight

Keysight N1000A DCA-X Series Manual de usuario

Keysight

Keysight N5990A Type-C Manual de usuario

Keysight

Keysight M8000 Series Manual de usuario

Keysight

Keysight InfiniiVision 1200 X Series Manual de usuario

Keysight

Keysight InfiniiVision DSOX1204A Manual de usuario

Keysight

Keysight N5281A Manual

Keysight

Keysight 85056A Manual

Keysight

Keysight 16034G Manual de usuario

Keysight

Keysight N2840A Manual de usuario

Keysight

Keysight U1401B Manual de usuario

Manuales populares de Equipo de prueba de otras marcas

SMART

SMART KANAAD SBT XTREME 3G Series Manual de usuario

Agilent Technologies

Agilent Technologies BERT Serial Manual de usuario

Agilent Technologies

Agilent Technologies N3280A Manual de usuario

Vernier

Vernier Go Direct Voltage Manual de usuario

Lifeloc

Lifeloc R.A.D.A.R. Manual de usuario

Fluke

Fluke T5-600 Instrucciones de funcionamiento e instalación

Mercury

Mercury TSL01 Manual de usuario

MAHA

MAHA MBT Series Manual de usuario

Fuji Electric

Fuji Electric P-61 Manual de usuario

ETC

ETC SealerAtor Manual de usuario

Skyfine

Skyfine ETHYWAY V2 Manual de usuario

Appion

Appion G5 Twin Manual de usuario

PCB Piezotronics

PCB Piezotronics 8159-0112A Manual de usuario

BW Technologies

BW Technologies MicroDock II Manual de usuario

Sun Nuclear

Sun Nuclear 1027 Manual de usuario

Biomark

Biomark HPR LITE READER Manual de usuario

Hioki

Hioki 3169-20 Manual de usuario

Ashcroft

Ashcroft ATE-100 Manual de usuario