Keysight X series Guía de inicio rápido

N9042B

Power Supply Upgrade

Option HW1

X-Series Signal Analyzer

INSTALLATION NOTE

Notices

The information contained in this document is subject to change without notice.

Keysight Technologies makes no warranty of any kind with regard to this material, including but

not limited to, the implied warranties of merchantability and fitness for a particular purpose.

Keysight Technologies shall not be liable for errors contained herein or for incidental or

consequential damages in connection with the furnishing, performance, or use of this material.

Manual Part Number

N9042-90012

Edition

Edition 1, January 2023

Supersedes: none

Printed in USA/Malaysia

Published by:

Keysight Technologies, Inc.

1400 Fountaingrove Parkway

Santa Rosa, CA 95403

Installation Note N9042-90012 3

Option HW1 – Power Supply Upgrade

This document provides detailed instructions for the installation of the Power Supply upgrade for

the N9042B UXA Signal Analyzer.

Please be sure to read this entire document before attempting to perform this upgrade. Then, be

sure to perform the steps in this procedure in the order that they are listed so that the installation

will complete properly, and the instrument will function as desired when completed.

Compatibility

This instrument option requires no specific instrument firmware version and is compatible with all

N9042B instruments. However, all instruments with option G2H do not require this upgrade, they

include it from the factory.

Instrument Calibration

The validity of any existing calibration that the instrument being upgraded may have will not be

affected by the installation of this upgrade.

Products Affected: UXA N9042B

To Be Performed By: (X) Keysight Service Center

( ) Advanced User

()User

Estimated Installation Time:

Estimated Adjustment Time:

Estimated Verification Time:

2.0 Hours

0.0 Hours

1.0 Hours

4Installation Note N9042-90012

What You Will Find in this Document

ESD Information............................................................................................................ page 5

Upgrade Contents ........................................................................................................ page 7

Tools Required .............................................................................................................. page 7

Initial Instrument Functionality Check ........................................................................ page 8

Option G2H Check.....................................................................................................page 8

Option ST1/ST2 Check..............................................................................................page 8

Option R40 Check......................................................................................................page 8

Upgrade Instructions.................................................................................................... page 9

Hardware Removal ....................................................................................................page 9

Hardware Installation ............................................................................................. page 20

Verify Operation ...................................................................................................... page 29

Instrument Button Up............................................................................................. page 30

Rear Panel Labels .................................................................................................. page 31

Adjustments and Performance Verification.............................................................. page 32

Manual Procedures Required................................................................................. page 32

Automated Utilities Required................................................................................. page 32

Automated Adjustments Required ........................................................................ page 32

Automated Performance Verification Testing Required ....................................... page 32

Installation Note N9042-90012 5

ESD Information

Protection from Electrostatic Discharge

Electrostatic discharge (ESD) can damage or destroy electronic components. All work on electronic

assemblies should be performed at a static-safe workstation. Figure 1 shows an example of a

static-safe workstation using two types of ESD protection:

— Conductive table-mat and wrist-strap combination.

— Conductive floor-mat and heel-strap combination.

Both types, when used together, provide a significant level of ESD protection. Of the two, only the

table-mat and wrist-strap combination provides adequate ESD protection when used alone. To

ensure user safety, the static-safe accessories must provide at least 1 megohm of isolation from

ground.

Figure 1 Example of a Static-Safe Workstation

These techniques for a static-safe workstation should not be used when working on circuitry

with a voltage potential greater than 500 volts.

6Installation Note N9042-90012

ESD Information

Handling of Electronic Components and ESD

The possibility of unseen damage caused by ESD is present whenever components are transported,

stored, or used. The risk of ESD damage can be greatly reduced by paying close attention to how all

components are handled.

— Perform work on all components at a static-safe workstation.

— Keep static-generating materials at least one meter away from all components.

— Store or transport components in static-shielding containers.

Test Equipment Usage and ESD

— Before connecting any coaxial cable to an analyzer connector, momentarily short the center and

outer conductors of the cable together.

— Personnel should be grounded with a 1 megohm resistor-isolated wrist-strap before touching

the center pin of any connector and before removing any assembly from the analyzer.

— Be sure that all analyzers are properly earth-grounded to prevent build-up of static charge.

For Additional Information about ESD

For more information about preventing ESD damage, contact the Electrical Over

Stress/Electrostatic Discharge (EOS/ESD) Association, Inc. The ESD standards developed by this

agency are sanctioned by the American National Standards Institute (ANSI).

Always handle printed circuit board assemblies by the edges. This will reduce the possibility of

ESD damage to components and prevent contamination of exposed plating.

Installation Note N9042-90012 7

Upgrade Contents

This upgrade kits includes a new higher capacity power supply assembly to replace the existing

one. This kit is intended to be used when the owner of the instrument has requested to have the

power capacity increased for one of the power intensive wideband measurement applications that

require it.

Tools Required

— TORX Driver, T-10

— TORX Driver, T-20

— Nut Driver, 5.5 mm

—Multi-BitTorqueDriver

— 5/8" Nut Driver

— 5/16" Wrench

Table 1 Upgrade Contents

Part Number Description Quantity

0515-0372 Screw, Panhead, TORX-T10 M3X0.5 8mm-LG 6

0515-1946 Screw, Flathead, TORX-T10 M3X0.5 6mm-LG 18

0515-2032 Screw, Flathead, TORX-T10 M3X0.5 8mm-LG 9

0515-2151 Screw, Flathead, TORX-T6 M2X0.4 4mm-LG 1

0535-0031 Nut-HEX W/Lock-Washer M3X0.5 2

0950-6424 Power Supply, AC-DC Switching, 695 W 1

N9041-00043 Rear Frame 1

N9041-00050 Blank Cover 1

N9041-00052 Nut Plate 1

N9042-80007 Label, KCC, 1220705 1

8Installation Note N9042-90012

Initial Instrument Functionality Check

Power on the instrument and allow it to complete its boot up process. Verify that there are no

instrument messages that would indicate that there is an issue with either the instrument hardware

or software. If there are any issues, investigate and fix the problem before continuing with this

upgrade.

Option G2H Check

While the instrument is still powered on check to see if the instrument has Option G2H installed. To

do so press System, Show System and look on the System Information screen for Option G2H.

If the instrument has Option G2H installed it does not need this upgrade, as it should already have

this hardware installed.

Option ST1/ST2 Check

While the instrument is still powered on check to see if the instrument has Option ST1 or ST2

installed. To do so press System, Show System and look on the System Information screen for

Option ST1 or ST2. Note whether one of these options is installed or not below.

Option ST1 or ST2 Installed: __________ Yes __________ No

Option R40 Check

While the instrument is still powered on check to see if the instrument has Option R40 installed. To

do so press System, Show System and look on the System Information screen for Option R40.

Note whether Option R40 is installed or not below.

Option R40 Installed: __________ Yes __________ No

The following procedure will ask you to make decisions based on whether or not these options are

installed in the instrument.

Installation Note N9042-90012 9

Upgrade Instructions

Hardware Removal

Dress Cover Removal

1. Turn the instrument off and disconnect the power cord.

2. Referring to Figure 2, remove the two screws (1) that attach the strap handles (2) from both

sides of the instrument and remove the strap handles.

Figure 2 Dress Cover Removal

3. Remove the four rear feet (4) by removing the four screws (3) and washers that attach them.

4. Remove the four bottom feet (6) by first removing the locking keys and then lifting the tabs

and sliding the foot toward the tabs.

5. Carefully slide the dress cover (5) off the instrument. This dress cover will not be reused.

10 Installation Note N9042-90012

Upgrade Instructions

Top Brace Removal

6. Referring to Figure 3, remove the fourteen flathead screws (1) and three panhead screws (2)

attaching the top brace (3) to the instrument and set it aside.

Figure 3 Top Brace Removal

Otros manuales para x series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Instrumento de medición de Keysight

Keysight

Keysight M9601A Manual del operador

Keysight

Keysight N5221A Manual del propietario

Keysight

Keysight N9030B Manual de instalación y operación

Keysight

Keysight N9021B MXA Guía de inicio rápido

Keysight

Keysight x-series Hoja de información del producto

Keysight

Keysight M9290A Manual de usuario

Keysight

Keysight E5505A Manual de usuario

Keysight

Keysight N432A Instrucciones de funcionamiento

Keysight

Keysight 478A Manual de servicio

Keysight

Keysight PD1000A Manual de usuario

Keysight

Keysight B2900A Manual de usuario

Keysight

Keysight HSA N9342C Manual de usuario

Keysight

Keysight M9485A Manual de usuario

Keysight

Keysight x series Manual de instalación y operación

Keysight

Keysight U8903A Manual de usuario

Keysight

Keysight N9320B Manual de usuario

Keysight

Keysight 537A Guía de inicio rápido

Keysight

Keysight M9703A Series Guía rápida

Keysight

Keysight N9030A-503 Manual de usuario

Keysight

Keysight N9320B Manual

Keysight

Keysight U1461A Manual de usuario

Keysight

Keysight U8903B Manual de usuario

Keysight

Keysight EXA X-Series N9010A Manual de usuario

Keysight

Keysight N2791A Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

ADTEK

ADTEK MW-5 Manual de usuario

Acterna

Acterna MS1400 Manual de usuario

Keysight x series Guía de inicio rápido

Manuales populares de Instrumento de medición de otras marcas