KERN YPS-03 Manual de usuario

KERN & Sohn GmbH

Ziegelei 1

D-72336 Balingen

E-Mail: info@kern-sohn.com

Phone: +49-[0]7433- 9933-0

Fax: +49-[0]7433-9933-149

Internet: www.kern-sohn.com

Installation Instructions

Balance table

KERN TYPS-03A-B

Version 1.0

2020-08

TYPS-03A-B-IA-e-2010

2 YPS-03-IA-e-1910

KERN TYPS-03A-B

Version 1.0 2020-08

Installation Instructions

Balance table

Contents

1Introduction ....................................................................................................... 3

2Technical data ................................................................................................... 3

3Assembly of the weighing table....................................................................... 4

3.1 Inner frame assembly ................................................................................................ 4

3.2 Outer frame assembly................................................................................................ 8

3.3 Final assembly..........................................................................................................10

4Attendance....................................................................................................... 10

YPS-03-IA-e-1910 3

1 Introduction

The KERN balance table was designed for laboratories and metrology rooms in order

to create suitable working conditions for devices that react sensitively to vibrations and

shocks.

The table comprises two different components:

•An integrated work space with shock-absorbing rubber blocks attached to a

stone slab

•An external work table with aluminium profile frame and height-adjustable feet

2 Technical data

KERN YPS-03

Item no./ Type TYPS-03A-B

Total dimensions (B x D x H) 800 x 600 x 785 mm (adjustable height)

Dimensions stone slab 300 x 400 x 80 mm

Weight stone slab 24 kg

Total weight 46 kg

4 YPS-03-IA-e-1910

3 Assembly of the weighing table

3.1 Inner frame assembly

1. Open the packing box, take out the top, middle, lower packing assemblies and the

accessory bags, See Figure 1.

2x granite

supporting rails

(long)

1x inner side rail

(righthand) 1x inner side

rail (lefthand) 1x granite

supporting rail

(below)

2x granite

supporting rails

(short)

Accessory Bag

Lower packing

Middle packing

Top packing

Figure 1

Inner frame packing

2. Remove the two granite supporting rails (long), the 2 granite supporting rails

(short) and the accessory bag from the lower packing layer.

3. Screw these parts together with the 4x M8x40 screws using the hexagon

wrench key from the bag in a way the resulting frame is plane and flat. (See

fig. 2)

Fig. 2

YPS-03-IA-e-1910 5

4. Remove the inner side rail (lefthand) from the upper packing layer and the

inner side rail (righthand) from the middle packing layer and fix them with the

M8x40 screws using the hexagon wrench. (See fig. 3)

5. Remove the lower granite supporting rail from the upper packing layer and fix

it by the two M8x40 screws; for this purpose open the two side frames slightly

in order to insert the rails into the frames. After that tighten the 6 screws as

shown in fig. 3.

After that the two sides should be aligned in a parallel and straight manner.

6. Fix the four rubber blocks as shown in fig. 4.

7. Put upon the granite block and center it as exactly as possible. Fig. 5 and 6

show the completely assembled inner table.

1 x Inner side rails (left) 1 x Granite

support rails 1 x Inner side rails (right)

1 x Supporting rail (lower)

6x M8x40 socket screws

Figure 3

Inner frame assembly

Take care that the screws are fitted in such a way that they are sunk in

the recesses.

(Do not allow screws to protrude - risk of injuries!)

6 YPS-03-IA-e-1910

rubbers

Figure 4

Assembled inner frame

YPS-03-IA-e-1910 7

Figure 5

Correct position of the granite

Figure 6

Assembled inner frame with granite

8 YPS-03-IA-e-1910

3.2 Outer frame assembly

1. Remove the outer side rail (right) from the lower packing, the table top

assembly from the middle packing and the outer side rail (left) from the top

packing (see Figure 7).

2. Fix them using four M8×40 screws with the hex key provided.

3. Remove the outer table supporting rail (upper front) from the lower packing

and fix it with four M8 x 40 screws.

4. Remove the outer table supporting rail (lower) from the top packing and fix it

with two M8 x 40 screws. You can open the 2 side frames a little in order to

put the rails inside the frames and then

5. tighten the 10 screws as Figure 8 shows.

6. Make sure the 2 sides are all parallel after the screws are tight. You can see

the assembled view in Figure 9

1x outer side rail

(righthand)

1x working surface

1x outer side rail

(lefthand)

1 x

crossbatten

outer frame

(below)

1 x crossbatten outer frame

(front top)

Lower packing

Middle packing

Top packing

Figure 7

Outer frame packing

YPS-03-IA-e-1910 9

1 x Outer side rail

(left)

1x Table top assembly 1 x Outer side rail (right)

10x M8 x 40 socket screws

1 x Outer table

supporting rail (upper

front)

1x Outer table supporting

rail (lower)

Figure 8

Outer frame assembly drawing

Figure 9

Assembled outer frame

10 YPS-03-IA-e-1910

3.3 Final assembly

Place the outer frame over the inner frame. Using the adjustment feet to level both

frames until they are in level position. Adjust the rubber blocks in a way that the

granite slab protrudes 2-5 mm over the working surface and rests firmly (see fig. 10).

1x Granite

1x Table top

4x Marble adjusting screws

1x Outer frame

1x Inner frame

8x feet

Figure 10

Final assembly drawing

4 Attendance

•Do not disassemble the weighing table without looking at the assembling

instructions.

•Do not shift the table by force or abruptly. We recommend you lift the table

and then cautiously put it down again.

•To clean off stains, wipe the table with a soft cloth soaked in detergent. Do

not use organic solutions for wiping off stains.

•Place the weighing table in a dry and clean environment. Do not install out

of doors. Do not use in the vicinity of fire or in environments with high

temperatures. Avoid exposure to direct sunlight.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Escala de KERN

Manuales populares de Escala de otras marcas

AWS

AWS ZEO-50 Manual de usuario

Gima

Gima Glass Body Fat Analyzer Manual de lista de piezas

Seca

Seca 374 Manual de usuario

TEC

TEC TEC SL59 SERIES Manual de usuario

Axis

Axis B/E Series Manual de usuario

Alecto

Alecto ACW-40 Manual de usuario

Rice Lake

Rice Lake MSI-4260 IS Manual de usuario

IKA

IKA RCT basic safety control Manual de usuario

ADE

ADE M20011 Manual de usuario

Duronic

Duronic KS3000 Manual de usuario

Digi

Digi SM-720 Manual de usuario

Cardinal

Cardinal CS Series Manual de usuario

Korona

Korona Kastella Manual de usuario

A&D

A&D FC-50Ki Manual de usuario

BDA

BDA CAMARGUE Manual de usuario

Tanita

Tanita HD-357 Manual de usuario

Leifheit

Leifheit 03173 Manual de usuario

Lumme

Lumme LU-1340 Manual de usuario