KEPO DAP9050-F5 Manual de usuario

Checkedby

Customer: QUARTZ-1

Applied To :

Product Name : Magnetic Transducer

ModelName : DAP9050-F5

Drawing No. : OEM2733

Compliance with ROHS

SPECIFICATION

SignatureofKEPO

Approved by

SignatureofApproval

Date

Issuedby

宁波凯普电子有限公司

Ningbo Kepo Electronics Co.,Ltd.

Drawing No.

Revision No.

Page

CONTENTS

ModelNo. :

Ningbo Kepo Electronics Co.,Ltd. http://www.chinaacoustic.com

1. Scope

围

2.General

概要

3.MaximumRating

额定极限条件

4.ElectricalCharacteristics

电性能

5.MeasurementBlockDiagram&ResponseCurve

测试图和曲线图

6.PhysicalCharacteristics

机械性能

7.EnvironmentalCharacteristics

环境性能

8.Dimensions

尺寸

9. PackagingStandard

包装标准

10.Cautions

警告

11.CautionsforUse

注意事项

12.Revision

履历表

2/9

1.0

OEM2733

SpecificationforMagneticTransducer

DAP9050-F5

Ningbo Kepo Electronics Co.,Ltd. http://www.chinaacoustic.com

2.1Out-Diameter: 9mm

外径： 9mm

2.2Height : 5.5mm

度： 5.5mm

2.3Weight : 1g.

重量： 1克

2.4CaseMaterial/Color: PBT/Black

壳体材质/颜色: PBT/黑

2.5According tothe No.7of RoHSExemptions,lead-based solderalloys

containing 85%byweight ormorelead(Sn10Pb90)

根据"欧盟RoHS指令豁免条款"第7条规定,使用了铅含量超过85%的锡铅合金焊料(Sn10Pb90)

2. 概要 General

This product specification is applied to the magnetic transducerinalarmsystems.Please

contact uswhen using this product foranyotherapplicationsthan described in the above.

本规格书适用于电磁式声响器，通常它用在系统中做报警或提的声响器用，如果将该产品

用于其它领域，请与我们取得联系。

1. 围 Scope

ModelNo. :

Page

Revision No.

Drawing No.

3/9

SpecificationforMagneticTransducer

OEM2733

1.0

DAP9050-F5

3. 额定极限条件 MaximumRating

储存温度围

Storage TemperatureRange

工作温度围

Operating Temperature Range

3.3

3.2

3.1

项目Item 规格Specification

-30 ～+80℃

-20 ～+70℃

额定电压

Rated Voltage 5V

3.4 工作电压

Operating Voltage 4～7V

4. 电性能 ElectricalCharacteristics

4.3

4.1

4.2

项目Item

Min.Sound PressureLevel

最小声压

Resonant Frequency

谐掁频率

Max.Rated Current

额定电流

规格Specification

85dB/5V/3.2KHz/10cm

3200Hz

70mA/5V

4.4

4.5

Coil Resistance

直流阻抗

Coil Impedance

交流阻抗

40±4Ω

80Ω

Ningbo Kepo Electronics Co.,Ltd. http://www.chinaacoustic.com

ModelNo. :

Page

Revision No.

Drawing No.

4/9

SpecificationforMagneticTransducer

OEM2733

1.0

DAP9050-F5

Part shall be measured underacondition (Temperature :+5 to +35 ℃,Humidity:45 to

85%R.H.)unless the standardcondition (Temperature :+25 ±3℃,Humidity:60

±10%R.H.)is regulated measure.

温度+25±3℃，湿度60±10%R.H.标准测试状态,在没有疑问的场合,可以在温度+5～

+35℃,湿度45～85%R.H.的围内测试.

5.3测试环境 Measuring Condition

5.2曲线图 ResponseCurve

电磁式声响器

MagneticTransducer

10cm

5. 测试方法 MeasuringMethod

输入信号:5V,3200Hz,正向方波

Input Signal:5V,3200HZ,Squarewave

5.1声压测试 S.P.L. Measuring

≥1m

声级计

Sound meter

065

090

080

2K 3K 4K 10KHz

070

075

085 dB

Ningbo Kepo Electronics Co.,Ltd. http://www.chinaacoustic.com

ModelNo. :

Page

Revision No.

Drawing No.

5/9

SpecificationforMagneticTransducer

OEM2733

1.0

DAP9050-F5

The force10 secondsof 9.8Nis applied to

eachterminalinaxialdirection.

分别在每个插针的轴向施加 9.8牛顿的静荷

重10秒.

先将产品的插针浸入松香液 5秒钟,然后浸

入+260±5℃熔融的锡槽中3±0.5秒.

Lead terminals areimmersed inrosin for5

secondsand then immersed insolderbath

of +260±5℃for3±0.5seconds.

Lead terminal areimmersed up to1.5mm from

sounder'sbody insolder bathof +300±5℃for 3±0.5

seconds or±260±5℃for10±1seconds,and then

sounder shall be measured afterbeing placed innatural

condition for4hours.

将产品的插针插入(插至距产品壳体1.5mm

处为止)+300±5℃的焊锡槽3±0.5秒或+260

±5℃的焊锡槽10±1秒,然后在常温中放4

小时后,进行测试。

Terminal

StrengthPulling

插针强度

6.5

Solderability

可焊性

6.4

Soldering Heat

Resistance

耐焊接性

6.3

Novisible

damage and

cutting off

插针没有断开和

可见的损伤

90%min. lead

terminals shallbe

wet withsolder.

(Except the edge

of terminal)

插针表面90%以

上被焊锡润湿.(插

针的段面除外)

峰值加速度980m/s2

, 正向方波,XYZ三个

方向各3次冲击实验后,进行测试。

Soundershallbemeasuredafterbeingapplied

shock(980m/s2

)foreachthreemutually

perpendiculardirectionstoeachof 3timesbyhalf

squarewave.

Sounder shall be measuredafter being applied

vibration of amplitude of 1.5mmwith10 to55Hzband of

vibration frequency toeach of 3perpendicular directions

for 2hours.

振动频率 10～55 Hz,1.5mm 全振幅,XYZ

三个方向各2小时试验后,进行测试。

实验条件

Test Condition

6. 机械性能 PhysicalCharacteristics

6.2

6.1

耐振动性

Vibration

Resistant

实验项目

Item

耐冲击性

Shock

实验后规格

Specification

符合表1的要求

The measured

value shall meet

Table1.

Ningbo Kepo Electronics Co.,Ltd. http://www.chinaacoustic.com

ModelNo. :

Page

Revision No.

Drawing No.

6/9

SpecificationforMagneticTransducer

OEM2733

1.0

DAP9050-F5

表1Table 1

7. 环境性能 EnvironmentalCharacteristics

将产品放于温度+80±2℃的烘箱内240

小时，然后取出，在常温下放4小时后，进

行测试。

Afterbeingplaced in achamberwith+80 ±2℃for240

hoursandthenbeingplacedinnaturalcondition for4

hours,soundershallbemeasured.

Afterbeing placed inachamberwith -30

±2℃for240 hoursand then being placed in

naturalcondition for4hours, soundershall

be measured.

将产品放于温度-30±2℃的制冷箱内240

小时，然后取出，在常温下放4小时后，进

行测试。

将产品放于90%～95%R.H.,温度+40

±2℃的环境试验箱内240小时，然后取出，

在常温下放4小时后，进行测试。

After being placed inachamber at -30±2℃for30

minutes, sounder shall be placed at room

temperature(+20℃).After 15 minutes at this

temperature,sounder shall be placed inachamber at

+80±2℃. After 30 minutes at thistemperature,

sounder shall be returned toroomtemperature(+20℃)

for 15 minutes.

After 5above cycles, sounder shall be measured

after being placed innatural condition for 4hours.

将产品先放于温度 -30±2℃的制冷箱内30分钟，然后

放于室温(+20℃)15分钟后, 放于+80±2℃的烘箱内

30分钟，再放于室温(+20℃)15分钟.

经过以上循环5次,在常温下放4小时后，进行测试。

声压级

SoundPressureLevel

项目

Item

Temperature

Cycle

温度循环

7.4

高温放

7.1

耐湿性

Humidity

7.3

低温放

DryHeatTest

(Storage)

ColdTest

(Storage)

7.2

实验项目

Item

试验后变化量

Specificationaftertest

初始值±10dB

Initial Value±10dB

实验后规格

Specification

符合表1的要求

The measured

value shall meet

Table1.

实验条件

Test Condition

Afterbeing placed inachamberwith 90 to

95%R.H. at+40±2℃for240 hoursand then

being placed innaturalcondition for4 hours,

soundershall be measured.

2- 0.6

4±0.5

3.0±0.3 5.5

DAP9050-F5

Ningbo Kepo Electronics Co.,Ltd. http://www.chinaacoustic.com

8. Dimensions

UNIT: mm

Tolerance: ±0.5

FIRSTANGLEPROJECTION

ModelNo. :

Page

Revision No.

Drawing No.

7/9

SpecificationforMagneticTransducer

OEM2733

DAP9050-F5 1.0

Ningbo Kepo Electronics Co.,Ltd. http://www.chinaacoustic.com

ModelNo. :

Page

Revision No.

Drawing No.

8/9

SpecificationforMagneticTransducer

OEM2733

DAP9050-F5 1.0

Pleasecontact usbeforeusing ourproductsforthe undermentioned applications

requiring especially high reliabilityinordertoprevent defectswhich might directly cause

damage tootherparty'slife, bodyorproperty(listed below).

⑴Aircraft equipment 飞行设备

⑵Aerospaceequipment 航天设备

⑶Undersea equipment 潜水设备

⑷Medicalequipment 医疗设备

⑸Transportation equipment (automobiles,trains,ships) 交通设施

⑹Traffic signalequipment 交通信号设备

⑺Disasterprevention/crimeprevention equipment 防灾害/防犯罪设备

⑻Data-processing equipment 数据处理设备

⑼Applicationsof similarcomplexityorreliabilityrequirementscomparable to the

applicationslisted inthe above 以及与上述相类似或可靠性要求更高的设备

如果产品使用于下列高可靠性的装时,请与我们取得联系,以免对人的生命,财产和身

体造成损害.

11. 注意事项 CautionsforUse

11.1如果产品所承受的机械应力超过规定的值,件可能被破坏.

11.2请注意保护工作电路不会因失误 ,跌落和温度变化而产生浪涌电压.

The component maybe damaged if mechanicalstress overthis specification is

applied.

Pleasepayattention toprotect operating circuit fromsurge voltage provided by

something of forcesuchasfailing ,shock and temperature changing.

Washing of the component is not acceptable. Becauseit is not sealded.

在使用烙铁的情况下,应注意烙铁头的温度应该保持在+350℃以下,并且焊接时间

控制在3秒内.

Incaseof using solderiron forsoldering, the top of soldering iron's

temperatureshouldbe kept less than +350 ℃.Moreoverthe soldering timeshould be

alsokept within3seconds.

9. 包装标准 Packaging Standard

产品的外包装是纸箱,它应该清楚的标明型号,数量,出厂检验批号.

在运输及储存的过程中,产品必须不会受到机械损伤.

Eachminimumpackage unit of productsshall be inacarton boxand itshall be clearly

marked withPart Number, quantityand outgoing inspection number.

Thereshall be no mechanicaldamage on productsduring transportation and/orin

storage.

11.3该产品不适合洗涤,因为它不密封.

11.4

10. 警告 Cautions

Ningbo Kepo Electronics Co.,Ltd. http://www.chinaacoustic.com

12. Revision

SpecificationforMagneticTransducer

ModelNo. :

Page

Revision No.

Drawing No.

9/9

Rev.

No. DATE PAGE DESCRIPTION SIGN

OEM2733

1.0

DAP9050-F5

92007.11.12 primary

1.0

Otros manuales de Transductor de KEPO

KEPO

KEPO DAP9050-F3 Manual de usuario

KEPO

KEPO DAP9050-E3 Manual de usuario

KEPO

KEPO DAP1206A-1933 Manual de usuario

KEPO

KEPO KPT-G1743-K6905 Manual de usuario

KEPO

KEPO L/KPMB1245-2915 Manual de usuario

KEPO

KEPO SMT-9640A Manual de usuario

KEPO

KEPO KPR-G3530 Manual de usuario

KEPO

KEPO KPT-G2223P8 Manual de usuario

KEPO

KEPO DAP9050-E5 Manual de usuario

KEPO

KEPO KPM-G1201A9-K9096 Manual de usuario

KEPO

KEPO KPT-1420A Manual de usuario

Manuales populares de Transductor de otras marcas

HBM

HBM AD101B Manual de usuario

Camille Bauer

Camille Bauer SINEAX F534 Manual de usuario

Trane

Trane KIT 16724 Instrucciones de montaje

Lumel

Lumel P18 Manual de usuario

B&C Speakers

B&C Speakers DE75PTN Manual de usuario

MAMAC SYSTEMS

MAMAC SYSTEMS PR-243 Manual

Mianyang Weibo Electronic

Mianyang Weibo Electronic WB Series Manual de usuario

ProMinent

ProMinent Dulcometer DMT Manual de usuario

MKS

MKS MicroPirani 925 Series Cómo utilizar

WIKA

WIKA WU-20 Manual de usuario

Alcatel Vacuum Technology

Alcatel Vacuum Technology BARATRON 622A Manual de usuario

Camille Bauer

Camille Bauer SIRAX CH-5610 Manual de usuario

WIKA

WIKA F2802 Manual de usuario

Veris Industries

Veris Industries PW Series Manual de usuario

HBM

HBM TJ1-S6 Manual de usuario

Simrad

Simrad ES120-7C - REV D Guía del usuario

HBM

HBM C18 Manual de usuario

Airmar

Airmar M260 Manual de instrucciones