Kenmore 721.62774100 Manual de usuario

iNSTALLATiON

iNSTRUCTiON

MANUAL

MODEL No.

721.62772

721.62774

721.62779

Read and save these

installation instructions.

I STALLATIO

INSTRUCTI

MicrowaveHoodCombination

Part No. 3828W5U0168

Printed in Korea

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

YOUR SAFETY FIRST

BEFORE YOU START

e Proper installation is the installer's responsibility!

- Read the entire manual before you begin. The Model number label is located on the oven front.

See Figure 1. Mounting plate is located on back side of microwave oven. See Figure 2.

BE SURE TO READ THE FOLLOWING SAFETY iNSTRUCTiONS:

Model Number Label

Mounting J

plate

(Remove from

oven to install.

Back of oven

Figure 1 Figure 2

WARNING

FOR YOUR SAFETY:

e You will need TWO people to install this oven. It is heavy and could cause personal injury ifnot handled

properly. The dimensions of the oven are as follows:

Height :16 7/16inches

Width : 29 15/16inches

Depth : 15 3/8 inches

Weight : 58 pounds

eAvoid Electrical Shock7

- Before you drill into the wall, note where electrical outlets are and where electrical wires might be behind

concealed the wall, YOU COULD GET AN ELECTRIC SHOCK it you contact electrical wires with your

drill bit.

- Locate and disconnect the power of any electrical circuits that could be affected by installing this oven.

IF YOU DO NOT DISCONNECT THE POWER, YOU COULD GET AN ELECTRIC SHOCK.

eELECTRICAL RATING OF THIS OVEN : 120V AC. 60Hz.

14 Amps /1600 Watts (Microwave oven + Cooktop Lamps + Ventilation Fan)

- You need a 120V, 60Hz, AC only, 15A or 20A, fused electrical supply (located in the cabinet above the

microwave as close as possible to the microwave circuit) serving only the microwave.

YOUR SAFETY FIRST

• THIS APPLIANCE MUST BE GROUNDED!

-If there isan electrical short circuit, grounding reduces the risk of electrical shock by providing an escape

wire for the electric current. This appliance isequipped with a cord having a grounding wire with a

grounding plug.

•Place the plug into a properly installed and grounded outlet. See Figure 3.

• Do not use an extension cord. PROPERLY POLARIZED AND

• Keep the power cord dry and do not pinch or crush it. GROUNDED OUTLET

• DO NOT, UNDER ANY CIRCUMSTANCES, REMOVE THE

POWER SUPPLY CORD GROUNDING PRONG!

This appliance MUST be grounded!

WARNING

Three-Pronged (Grounding) plug

Figure 3

If you use the grounding plug improperly, you risk electric shock!

- Check with a qualified electrician if you are not sure whether the oven is properly grounded or if you do

not completely understand the grounding instructions.

DO NOT USE A FUSE IN THE NEUTRAL OR GROUNDING CIRCUIT.

WARNING

Improper grounding could result in electric shock or other personal injury.

SAVE THESE INSTRUCTIONS FOR THE LOCAL ELECTRICAL INSPECTOR'S USE.

•DO NOT EXPOSE YOURSELF TO EXCESSIVE MICROWAVE ENERGY!

-DO NOT try to operate the microwave oven with the door open.

- DO NOT tamper with or defeat the safety interlocks.

- DO NOT place objects between the microwave oven front face and the door.

- DO NOT allow soil or cleaner residue to build up on the flat surfaces around the microwave oven door.

- DO NOT operate the microwave oven if it is damaged.

- The microwave oven door must close properly to operate safely.

- DO NOT USE THE MICROWAVE OVEN:

• If the door is bent.

• If the hinges or latches are broken or loose.

• If the door seals, sealing surfaces or glass is broken.

- DO NOT ATTEMPT TO ADJUST OR REPAIR THE OVEN YOURSELF!

It should be adjusted and repaired by a qualified technician who can check for microwave leakage

after repairing the oven.

WARNING

If you do not use the microwave oven as instructed, you could

be exposed to excessive microwave energy.

YOUR SAFETY FIRST

MAKE SURE YOU HAVE ENOUGH SPACE AND SUPPORT.

- Mount the oven against a flat, vertical walt, so that it is supported by the walt. The wall should be

constructed of minimum 2" x 4" wood studding and 3/8" thick drywall or plaster/lath.

- ATTACH AT LEAST ONE of the two tag screws supporting the oven to a vertical, 2" x 4" wall stud.

- DO NOT mount the microwave oven to an island or peninsula cabinet.

- BE SURE the upper cabinet and rear wall structures are able to support 150 lbs., plus the weight of any

items you place inside the oven or upper cabinet.

- Locate the oven away from strong draft areas, such as windows, doors, and strong heating vents.

- BE SURE you have enough space. See Figure 4 below for minimum vertical and horizontal clearance.

WARNING

If you do not mount the oven as instructed,

you risk personal injury and/or property damage.

30" rain. cabinetopeningwidth

30" rain,clearancefrom bottom

of cabinetto cooking surface

or countertop

(Use templates included

with installation instructions)

_Grounded Plug

(inside upper cabinet)

Power Supply

Cord Hole

Figure 4

CAUTION

•Before you begin installing the oven, PLACE APIECE OF THE CARTON OR OTHER HEAVY

MATERIAL (a blanket) over the countertop or cooktop to protect it. Do not use aplastic cover.

Failure to protect these surfaces could result inproperty damage.

PARTS, TOOLS, MATERIALS

THE FOLLOWING PARTS ARE SUPPLIED WITH THE OVEN:

NOTE: Depending on your ventilation requirements, you may not use all of these parts.

Damper/duct connector

(for roof-venting or wall-venting installation)

Not Actual Size

One power cord clamp and

One dark-colored mounting screw

(to hold the power cord)

Actual Size

Two tapping screws - Actual Size

(for attaching the damper duct connector) One lock pin and one washer-Not Actual size

One power cord clamp bushing - Actual Size

(for the cord hole in a metal upper cabinet)

Four 1/4" x2" lag screws - Actual Size

(for wail stud holes) Four 1/4" x3" toggle bolts - Actual Size

(for drywall holes)

Two 1/4" x2" bolts - Actual Size

(for securing to the upper cabinet)

Two washers - Actual Size

(for the two upper cabinet bolts)

Four spring toggle heads - Actual Size

(for the toggle bolts)

NOTE: You need to install at least one tag screw into a 2" x 4" stud and four anchor bolts into the wall and

the mounting area must meet the 150 lbs. weight requirement.

PARTS, TOOLS, MATERIALS

YOU WILL NEED THE FOLLOWING TOOLS AND MATERIALS FOR THE INSTALLATION:

Carton or other heavy material for covering the counter top.

Clear tape

(for taping the templates to the wall) Stud finder or thin nail.

Key hole saw (for the power cord hole)

Saber saw (for cutting vent

hloes for roof or wall venting)

Phillips screwdriver (for the screws)

Pencil

Flat blade screwdriver (for the bolts)

3/8" and 3/4" wood drill bits

1/2" and 3/16"

drill bits

Plumb line

Measuring tape (metal preferred) Duct Tape

Small side cutters or tin snips Caulking gun

•If you have brick or masonry walls, you need special hardware and tools.

• The ductwork you need for the installation is not included. All wall and roof caps must have a back-draft

damper.

STEP 1: PREPARE THE

ELECTRICAL CONNECTIONS

WARNING

AVOID ELECTRICAL SHOCK! THIS APPLIANCE MUST BE GROUNDED!

1. Locate the grounded electric outlet for this oven in the

cabinet above the oven, as shown in Figure 4 Detail.

NOTE: The outlet should be on a circuit dedicated to the

microwave oven 120V, 60Hz., AC only, with a

20ampere fused electrical supply.

IMPORTANT: If you do not have the proper walt outlet, you

MUST have one installed by a qualified

electrician.

2. You will cut the power-supply-cord hole (shown in

Figure 4 Detail) later when you prepare the wall and

upper cabinet in Step 4.

NOTE: Do not use an extension cord.

Keep the power cord dry and do not pinch or

crush it.

UaPl°Pienret...[

•Grounded Outlet

Power-Supply-Cord Hole

Figure 4 Detail

WARNING

Improper grounding could result in

electric shock or other personal injury.

•DO NOT, UNDER ANY CIRCUMSTANCES, REMOVE THE POWER

SUPPLY CORD GROUNDING PRONGf This appliance MUST be

groundedf

m7m

STEP 2:

PREPARE THE VENTING SYSTEM

NOTE: The ductwork you need for outside ventilation is not included with your oven. The standard

ductwork fittings and length are shown in Figure 9, page 9.

kWARNING-FIRE HAZARD k

THIS OVEN MUST BE PROPERLY VENTED!

You may vent your oven in one of three ways:

Roof-venting If your oven is located on an outside wall near the roof, as in Figures 6 (31/4" x

10" duct) and 8 (6" round duct.)

Wall-venting If your oven is located on an outside wall on the first floor of your house, as in

Figures 5 (3 1/4" x 10" duct) and 8 (6" round duct.)

Room-venting If your oven is located on an inside wall of your house, as in Figure 7.

NOTE: Ifyou choose the rear exhaust method (roof-or wall-venting), be sure there is enough clearance

within the wall for the exhaust duct.

cabinet

Wallventing

Wall Venting

3 1/4"x10"

duct

*-wall cap

through-the-wall

Figure 5

cabinet

Roof

Roof Venti ng

venting

roof cap

3 l_'ctl0" __j

through-the-roof

Figure 6

REMEMBER AS YOU INSTALL THE

VENTING:

• Keep the length of the ductwork and the

number of elbows to a minimum to

ventilate your oven efficiently.

See examples on page 9.

• Keep the size of the ductwork the same.

• Do not install two elbows together.

• Use duct tape to seal all joints in the duct

system.

• Use caulking to seal the exterior wall or

roof opening around the cap.

cabinet

ove

Room Venting

Figure 7

roof cap

6" min.

diameter wall cap

round duct

elbow

3 1/4" toround _t

duct transition 3 1/4"to round

ductworktransition

Figure 8

STEP 2:

PREPARE THE VENTING SYSYTEM

STANDARD FITTINGS

NOTE: If the existing duct is round, you must use a rectangular-to-round adapter, with a rectangular 3"

extension duct installed between the damper assembly and the adapter to prevent the exhaust

damper sticking.

DUCT LENGTH

The total length of the duct system, including straight duct, elbows, transitions, wall or roof caps must not

exceed the equivalent of 140 feet.

For best performance, do not use more than three 90 degree elbows.

Below are the standard fittings and their equivalent length in feet.

3 1/4"x10"

to 6"=5ft.

3 1/4"x10" roof

cap=24ft.

3 1/4"x10" 90 °

elbow=25ft.

90° elbow

=1Oft.

3 1/4"x10"

wall cap

=40ft.

45 °elbow

=5ft.

3 1/4"x10"

flat elbow

=10ft.

Figure 9

To calculate the equivalent length of each duct piece used, see the examples below.

For 3 1/4"x10" SYSTEMS

301/4;;b17'w _ 6ft. _ wall cap

}rz ,

1-3 1/4" x10" 90° elbow

1-Wall Cap

8 feet straight duct

TOTAL LENGTH

Examples

25 ft.

40 ft.

8ft.

73 ft.

For 6" ROUND SYSTEMS

wall cap

90 ° elbows _ 6ft. "-_1_

transi_

1-transition = 5 ft.

2-90 °elbows = 20 ft.

1-Wall Cap = 40 ft.

8 feet straight = 8 ft.

TOTAL LENGTH = 73 ft.

STEP 3:

PREPARE THE VENTING BLOWER

Your microwave oven is shipped with the blower assembled for room-vented(recirculating). You need to

adjust the blower if you want wall-venting or roof-vented installation.

WARNING

ELECTRICAL SHOCK HAZARD!

UNPLUG UNIT BEFORE WORKING ON IT.

•DO NOT PULL OR STRETCH THE BLOWER WIRING! Pulling and stretching the blower wiring

could result in electrical shock.

Remove two screws that attach mounting plate to microwave

oven cabinet. See Figure 10.

Remove mounting plate and set aside. Replace the screws.

ROOM-VENTED INSTALLATION:

Go to STEP 4 on page 12.

WALL-VENTED INSTALLATION"

1. Remove one blower unit mounting screw and two blower

plate screws. Remove the blower plate from cabinet.

See Figure 11.

2. Carefully lift the blower unit out of the microwave oven.

3. Use side cutters or tin snips to cut and remove knockouts

"B" from Back plate. Discard knockouts.

Be careful not to distort the plate. See Figure 12.

4. Reassemble the blower wire.

See Figure 13.

5. Rotate the unit so that the exhaust ports face the rear of the

cabinet. See Figure 14. When you insert blower unit, blower

wire must be like figure 14.

6. Place blower unit back into cabinet. Check that the exhaust

ports face towards the rear of the cabinet.

See Figure 15.

7. Reattach the blower plate to cabinet so the exhaust ports

and blower plate opening are aligned. Attach with one

blower unit mounting screw and then two blower plate

mounting screws. See Figure 16.

Remove

two screws

blower unit

Remove

mounting

plate.

Figure 10

-- back plate

plate

mounting screws

Knockouts"B" %o...

blower plate blower unit

mounting screw

Figure 11

_Figure 13

__Knockouts 'B'

Figure 12

--10--

Figure 14

unit

exhaust

ports

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Microondas de Kenmore

Kenmore

Kenmore 721.80002 Manual de usuario

Kenmore

Kenmore 721.80002 Manual de usuario

Kenmore

Kenmore 405.24303410 Manual de usuario

Kenmore

Kenmore 565.66101 Manual de usuario

Kenmore

Kenmore 111.71312810 Manual de usuario

Kenmore

Kenmore Toast'n'wave 721.62292 Manual de usuario

Kenmore

Kenmore 405.73114310 Manual de usuario

Kenmore

Kenmore Microwave hood combination 721.80802 Manual de usuario

Kenmore

Kenmore 790.4960 series Manual de usuario

Kenmore

Kenmore 721.80494 Manual de usuario

Kenmore

Kenmore 721.69113 Manual de usuario

Kenmore

Kenmore 665.62612 Manual de usuario

Kenmore

Kenmore ULTRA WAVE 665.61652 Manual de usuario

Kenmore

Kenmore 401.8504 Series Manual de usuario

Kenmore

Kenmore Elite 111.72219 Manual de usuario

Kenmore

Kenmore 721.86012 Manual de usuario

Kenmore

Kenmore 69612 Manual de usuario

Kenmore

Kenmore 721.61102 Manual de usuario

Kenmore

Kenmore 767. 8933000 Manual de usuario

Kenmore

Kenmore 790.8036 Manual de usuario

Kenmore

Kenmore Elite 721.88512 Manual de usuario

Kenmore

Kenmore 88522 Manual de usuario

Kenmore

Kenmore 665.60639 Manual de usuario

Kenmore

Kenmore 721.80032 Manual de usuario

Manuales populares de Microondas de otras marcas

Daewoo

Daewoo KOG-574R0S Manual de usuario

LG MH7040SS Manual de usuario

Sharp

Sharp R-895(AL)M Manual de usuario

Dometic

Dometic DOTRM13W Manual de usuario

Sanyo

Sanyo EM-X680 Manual de usuario

Sharp

Sharp R-393M Manual de usuario

KitchenAid

KitchenAid KMCX4510 Instrucciones de instalación

Smeg

Smeg S45MCX1 Manual de usuario

Russell Hobbs

Russell Hobbs RHM2044 Manual de usuario

Sunbeam

Sunbeam SMW759 Manual de usuario

Gallet

Gallet FMOE230S Manual de usuario

Bosch

Bosch CEG732X.1B Manual de usuario

Dometic

Dometic Roadmate 230 Manual de usuario

Samsung

Samsung SJ0396W Manual de usuario

Sanyo

Sanyo EM-P494WS Manual de usuario

Sharp

Sharp R-240 Manual de usuario

Electrolux

Electrolux EMS2840 Manual de usuario

Daewoo

Daewoo KOC-984T2S13 Manual de usuario