Kenmore 1700 - 6 Gallon Humidifier Manual de usuario

READ AND SAVE THESE INSTRUCTIONS

Use and Care Guide

TOWER HUMIDIFIER

6 Gallon Output with

Digital Readout

Model 758.17006

'\ i/

CAUTION: Before using this

product, read this manual and

follow all its Safety Rules and

Operating instructions,

• Safety

•Assembly

° Operation

•Maintenance

•Parts

• Espa_ol, pg,17

Sears, Roebuck and Co, Hoffman Estates, 1L USA,

Part No, 1B71756

wwwsears,com

Printed in China

GENERAL SAFETY INSTRUCTIONS

Safety Signal Words

DANGER: Means if the safety

information is not followed someone

will be seriously injured or killed.

WARNING: Means if the safety

information is not followed someone

could be seriously injured or killed.

CAUTION: Means if the safety

information is not followed someone

may be injured.

1. To reduce the risk of fire or

shock hazard, plug humidifier

directly into a 120 V, AC

electrical outlet. Do not use

extension cords,

2. Keep the electric cord out of

traffic areas. To reduce the

risk of fire hazard, never put

the electric cord under rugs,

near heat registers, radiators,

stoves or heaters.

3. Always unplug the humidifier

before moving it, before

cleaning, or whenever the

humidifier is not in service,

WARNING: To reduce risk of

fire, electric shock, or injury

always unplug before servicing

or cleaning_

4. Keep the humidifier ctean

5, Do not put foreign objects

inside the humidifier.

6. Do not allow to be used as a

toy° Close attention is

necessary when used by or

near children.

7Never use your humidifier

while any part is missing or

damaged in any manner.

8. To reduce the risk of electrical

hazard or damage to

humidifier, do not tilt, jolt or tip

humidifier while unit is

running.

9, To reduce the risk of damage

to humidifier, unplug when not

in use_

10. To reduce the risk of

accidental electrical shock, do

not touch the cord or controls

with wet hands.

11. To reduce the risk of fire, do

not use next to an open

flame source, such as a

candle or other flame source.

12. Note the warning label

shown adjacent.

Table of Contents '

General Safety information ............ 2

Know Your Humidifier ..................... 3

How Your Humidifier Works ........... 4

Getting you Humidifier Up

and Running ................................ 4

Location ...................................... 4

Electrical Hook-up ....................... 5

Water Fill ....... ................................ 6

Setting the Controls .................... 7

Operating the Controls .................. 7

Using Your Humidifier ................... 8

Filter Replacement and Care ...... I0

Cleaning and Maintenance .......... 11

Troubleshooting ......................... 13

Parts List for Kenmore

PIN 758.17006 ............................ 14

Warranty Information ................... 15

KNOW YOUR HUMIDIFIER

HUMIDITY &

FAN CONTROLS

FAN

ASSEMBLY

BOTTLE

HANDLE

REPLACEMENT

FILTER

15508

BASE

Descri_tioq

*Gallon Output 24/hrs

Capacity of Bottle

Capacity of Base

*Sq, Ft. Coverage

Fan Speeds

Auto Fan Speed

Replacement Filter

Auto Humidistat

Auto Shut Off

Controls

UL Listed

Volts

Hertz

Amps (High Speed)

Watts (High Speed)

758.17006

6 gal.

t ,25 gal.

1 25 ga!.

t 300

Yes

15508

Yes

Electronic (Push Button)

Yes

120 A,C,

1,2

*Based on an area with average insulation and an 8 foot ceiling

height.

How Your Humidifier Works

Your new humidifier is designed to satisfy home humidity requirements through

the principle of evaporation of water in the air.

Once the filter becomes saturated, air is drawn in, passes through the filter and

moisture is absorbed into the air. All evaporation occurs in the humidifier so any

residue remains in the filter. This natural process of evaporation virtually

eliminates white dust.

CAUTION: To reduce the risk

of injury, fire or damage to

humidifier, use only cleaners

specifically recommended for

humidifiers. Never use

flammable, combustible or

poisonous materials to clean

your humidifier. To reduce the

risk of scalds and damage to

humidifier, never put hot water

in humidifier.

Getting Your

Humidifier Up

and Running

Once removed from its carton,

remove all packing materials,

Verify the filter is properly installed

(See page 10).

Step 1. Location

WARNING: For your own safety, do not use humidifier if any parts are ]

damaged or missing. /

Selecting a Location

Place humidifier on a flat Ievel surface;

take extra care in leveling when placing

the unit on carpet. Position the humidifier

where the most humidity is needed or

where the most air will be circulated

throughout the house such as near a cold

air return.

Moist air (humidity) produced will

disperse into the whole house, but

the area closest to the unit will

have the highest humidity If the

unit ispositioned close to a

window, condensation may form

on the window pane_ If this occurs

the unit should be repositioned in

another location

Positioning the Unit

The humidifier should be positioned with

the back (cord exit side) and sides, at

least 2 inches away from the wall, Air

needs to enter through all of the louvers

in the housing assembly in order for the

humidifier to operate at peak efficiency.

NOTE: Be sure humidistat (located

approximately 4 inches outside humidifier

body on power cord) is free from

obstruction and away from any hot air

NOTE: Due to release of cool, moist air from humidifier, it is best to direct air

away from thermostat and hot air registers and to position humidifiers next to an

inside watl_ Unit should not be placed where cold air from outside walls or warm

air from a hot air register blows directly on it,

Step 2. Electrical Hook-Up

Locate nearest t20V AC_ wall socket in the location desired, preferably on

inside wall. With the humidifier in the desired location, route the electrical cord

safely so no one will trip or upset the humidifier.

Plug in the electrical cord

WARNING: To reduce the risk of fire or shock hazard, only plug humidifier l

into a 120V A.C_ outlet. Do not use extension cords. J

To reduce the risk of electrical shock, this

humidifier has a polarized plug (one blade

is wider than the other), This plug will fit in

a polarized outlet only one way,

If the plug does not fit fully in the outlet,

reverse plug. If it still does not fit, contact

a qualified electrician to install the proper

outlet. Do not change the plug in any way

Step 3. Water Fill

WARNING: To reduce the risk of fire

or shock hazard, do not pour or spill

water into control or motor area. If

controls get wet, let them dry

completely and have unit checked

by qualified service personnel before

plugging in

After the humidifier is positioned

where it will be operating, you are

ready to fill the humidifier. The bottle

tilts out and away from the base.

Take care not to bump or damage fill

valve assembly on the bottom of the

bottle.

Invert the bottle, Press the valve

stem button into the bottle and turn

clockwise to lock in open position°

Place bottle under the faucet Fill the

bottle, being careful not to allow any

debris to get in the valve seating.

Once the bottle is full, press the

valve stem button and turn counter

clockwise to release and close_

___i _i i i

PUSHIN TURN

CLOCKWISE

Press vak,e stemand turnckx:kwiseto_ock

in open positbn - Counterclockwise to

release and

CAUTION: Use only 32-14900 EPA

Registered Bactedostat from Sears.

Under no circumstances should you

use water treatment products designed

for Rotobelt or Ultrasonic humidifiers.

Place the water bottle back into the

humidifier base° When positioned

properly, the plunger will open and

the water will flow into the base. The

base will hold the entire contents of

the water bottle. Once the bottle is

empty, remove it and repeat the

filling process° The humidifier is now

filled to capacity. For less frequent

filling let the humidifier exhaust both

the water from the bottle and the

base before filling.

Assembly

Step 4. Setting the Controls

Where you set your

desired humidity Ievels

depends on your personal

comfort level, outside

temperature and inside

temperature, A starting

Set point of 30%-40%

ROOM humidity is

recommended but there

may be conditions that

require a different setting.

Recommended

When Outdoor Indoor Relative

Temperature is: Humidity is:

-10°F -24°C 20%

2°F -18"C 25%

10°F -12°C 30%

> 20°F -6°C 35%

The chart provided offers general guidelines for selecting indoor humidity.

IMPORTANT: Water damage may result if condensation starts to form

on windows or walls, Humidity SET point should be lowered until

condensation no longer forms, We recommend room humidity levels

do not exceed 50%,

Operating the Controls

Digital Display

Press the power button once to turn

the unit on* _). Initially there is a slight

delay while the electronics calibrate.

Two bars (--) appear during this timer

Once calibration is complete a ROOM

humidity reading between 20% - 95%

will be displayed, A flashing 20 display

indicates that the room humidity is less

than 20%.

NOTE: The default settings at initial

startup are (LOW) F1 fan speed and

65% SET humidity, After desired settings

are selected by the user, they remain as

long as the unit remains plugged in and

there is no power interruption, If the unit

is unplugged the original default settings

are employed,

Function

Buttons

Digital Display

*Humidifier fan should operate at

initialstartup, If itdoes not, refer

to "Fan not operating (digital

display is illuminated)" in the

"Troubleshooting" section on

page 13 of this manual.

Operating the Controls =continued

Speed Button O

This humidifier is equipped with a

3-speed fan control. Initially depressing

the speed button will display the current

speed setting, Each push of the speed

button advances the mode through the

settings of(HIGH) F3, (MEDIUM) F2,

(LOW) F1 and (AUTO) A.

The selected setting is displayed on the

digital readout. The higher the setting,

the faster water is evaporated and

released into the air. F1 (LOW) is the

quietest setting and is provided for

conditions that do not require a rapid

evaporation rate. When (AUTO) A is

selected the humidifier wili determine the

required fan speed needed to bring the

actual room humidity up to the set

humidity. Speed

BL_tton Humidity

,..__utton

Humidity Control i_1

This button allows you to adjust

the humidity to suit your needs,

This humidifier wilt automatically

cycle on and off as required to

maintain the selected setting The

readout displays both actual

(ROOM) and desired (SET)

humidity percentage (%) settings

when humidity control button is

pressed. The ROOM readout has

a range of 20% to 95%. If the

room humidity level is equal to or

less than 20% the display will

show a flashing 20.

The SET readout has a range of

25% to 65% and is adjusted in

increments of 5%. Initially

depressing the humidity button will

display the current humidity

setting,. Each additional press of

the button increases the setting by

5%. A SET point of 65% operates

the humidifier continuously

regard]ess of the ROOM reading,

The humidistat that senses the

readings is located on the power

cord. Insure that it is free from

obstructions°

Using Your Humidifier

Refill Display

For maximum run time both the bottle

and the base should be filled. When

both the bottle and the base are empty

the display alternates the room

humidity reading and "F" (FILL),

indicating that additional water is

required. Also at this time the unit will

automatically switch into DRY OUT

MODE and continue to run on the

lowest speed until the filter is dry. Refill Display

NOTE: During this time the room humidity level will continue to be monitored and

the humidifier wil! cycle the fan on and off until the filter is completely dry, The fan

will shut off leaving you with a dry humidifier that is less prone to mold and mildew

growth. If DRY OUT MODE is not desired, refill the humidifier with water and the

fan will return to the set speed.

NOTE: Fan automatically switches to lowest speed during DRY OUT MODE

Check Filter indicator

The ability of any humidifier to efficiently supply

humidity output relies heavily on the condition

of the filter. As the filter loads with impurities it

gradually loses its wicking capability. When this

happens, moisture output is reduced and the

humidifier has to work longer to satisfy the

selected setting. This humidifier has a check

filter reminder timed to appear after 720 hours

of operation. When display shows an

alternating "CF" and "room humidity" setting at

5 second intervals it is a reminder to check the

filter condition°

Ctl#{;k r,tlt{_r

Display

Humidistat

The humidistat located on the power

cord senses the percentage of

humidity in the air. tt causes the

humidifier to cycle on and off to

maintain the selected humidity SET

point° The fan will turn on if the

"ROOM" reading falls 3% below the

SET point and will continue to run the

humidifier until a reading of 1% above

the SET point is achieved. The fan

wilt turn off until the ROOM reading

falls 3% below the SET point again.

NOTE: Be sure that the humidistat,

which is located on the power cord, is

free from obstruction and away from

any hot air source,

Control Lock Out

To avoid unwanted tampering with the

humidifier settings the controls can be

locked,

Activation Procedure

After the humidifier functions have been

set up, hold the power button down for

5 seconds° The display will show "CL"

for 2 seconds; release the power button

and the control will resume the display

of the room humidity. The room

humidifier will continue to function with

the locked in settings, If buttons are

operated while "CL" is active, the "CL"

is displayed and settings are

unaffected,

Deactivation Procedure

To deactivate the "CL" function simply

press and hold the power button for 5

seconds. "CL" will flash at the rate of t

second on and 1 second off for a period

of 2 seconds and then resume the

display of room humidity.

Filter Replacement and Care

CAUTION: To help retard bacteria

growth and keep maximum

efficiency, the filter should be

replaced at least once per season,

or more often under hard water

conditions, Use Kenmore 15508

replacement filter.

WARNING: To reduce the risk of

shock or injury from moving parts,

always unplug humidifier before

removing or replacing any parts,

Replace the evaporative wicking filter

at least once per humidification season

or more depending on water conditions

in your area_

Filter Replacement

1. Unplug humidifier. Before removing

the filter, move the humidifier to an

area not susceptible to water damage.

(i e, kitchen or bath areas).

2. Remove the water bottle and set

aside° Be sure not to bump or damage

the fill valve,

3o The upper housing and the base are

held together by two hooks at the front

of the housing and a flexible snap in

the rear, To remove the housing, press

in on the triangular shaped snap at the

rear of the humidifier, below the cord

exit, while lifting upward, tilting the

upper housing forward to clear the

hooks at the front of the base.

4. Set the upper housing aside.

The filter is now accessible.

5, Take note of the filter position.

Remove the filter. You may want

to clean the base at this time See

the "Cleaning and Maintenance"

section of this manual

6, Install anew filter (15508) into

the base, Position the filter

between the uprights in the bottom

of the base. The filter should be

resting on the floor of the base.

7. Return the upper housing to the

base by first placing the hooks

located near the front of the base

into the mating holes in the upper

housing, Then tilt the upper

housing down towards the base

until the rear snap engages the

main housing

8, Reposition the humidifier to its

operating position,

9, The humidifier is now ready to

be filled for operation.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Humidificador de Kenmore

Kenmore

Kenmore KEMORE 758.144533 Manual de usuario

Kenmore

Kenmore 758.15420011 Manual de usuario

Kenmore

Kenmore KENMORE 1700 Manual de usuario

Kenmore

Kenmore Kenmore Quiet Comfort 758.144120 Manual de usuario

Kenmore

Kenmore 2.0 & 3.5 gallon warm mist humidifier... Manual de usuario

Kenmore

Kenmore 42.14121 Manual de usuario

Kenmore

Kenmore 758.15408 Manual de usuario

Kenmore

Kenmore Sears Evaporative table top Humidifier 42.14121 (3... Manual de usuario

Kenmore

Kenmore 758.144108 Manual de usuario

Kenmore

Kenmore 758.154120 Manual de usuario

Kenmore

Kenmore Sears 758.144071 Quiet comfort Manual de usuario

Kenmore

Kenmore Kenmore 758.144118 Manual de usuario

Kenmore

Kenmore Sears 758.144530 Manual de usuario

Kenmore

Kenmore 758.299825C Manual de usuario

Kenmore

Kenmore 2500 Manual de usuario

Kenmore

Kenmore Sears 758.144107 Quiet comfort Manual de usuario

Kenmore

Kenmore 758.17006 Manual de usuario

Kenmore

Kenmore Quiet Comfort 758.144150 Manual de usuario

Kenmore

Kenmore QUIET COMFORT 758.14417 Manual de usuario

Kenmore

Kenmore 303.147012 Manual de usuario

Kenmore

Kenmore 758.154120 Manual de usuario

Kenmore

Kenmore 758.15408010 Manual de usuario

Kenmore

Kenmore 758.154200 Manual de usuario

Kenmore

Kenmore 758.144161 Manual de usuario

Manuales populares de Humidificador de otras marcas

Boneco

Boneco H300 Manual de usuario

Bionaire

Bionaire CM1 Manual

Air-O-Swiss

Air-O-Swiss AOS 7131 Manual

KING

KING K 5002 Rainbow Manual de usuario

Crane

Crane EE-6902 Manual de usuario

Glaziar

Glaziar Ness Manual de usuario

Philips

Philips DreamStation Go Dimensiones

Honeywell

Honeywell MISTMATE HUL520BC Manual de usuario

Stadler Form

Stadler Form Hera Manual de usuario

Hunter

Hunter 31206 Manual de usuario

TaoTronics

TaoTronics TT-AH004 Manual de usuario

adorini

adorini Cigar Heaven Manual de usuario

Lanaform

Lanaform Aroma Manual de usuario

Aprilaire

Aprilaire 800 Series Manual de usuario

Pyle

Pyle SereneLife PHUMDIF8 Manual de usuario

Trotec

Trotec B 200 Manual de usuario

Pure Humidifier

Pure Humidifier EC Series Manual de usuario

Crane

Crane EE-864 Manual de usuario