Keller MANO GAUGE Manual de usuario

KELLER

ANO

AUGE

/ M

ANO

ECORD

RANGE SERIAL-NO. PROGRAM-VERSION DATE

GENERAL DESCRIPTION PAGE 1

OPERATION PAGE 2

MEASURING MODE /C

OMMAND STRUCTURE

MANO-MODE PAGE 3

SETTING NEW ZERO REFERENCE

ZERO-MODE PAGE 4

ADJUSTING THE MEASURING CYCLE

MECY-MODE PAGE 5

SELECTION OF DISPLAY

DISE-MODE*PAGE 6*

SELECTION OF VALUES TO BE MEASURED

SAVS-MODE*PAGE 8*

PREPARING THE STORAGE PARAMETERS

REC-SEL-MODE*PAGE 9*

STARTING THE RECORDING

REC-MODE*PAGE 10 *

READ-OUT OF THE STORED VALUES PAGE 11

NOTES PAGE 12

INSTRUMENTS WITH ANALOG OUTPUT PAGE 13

TECHNICAL DATA PAGE 14

PRESSURE GENERATION OPTIONS PAGE 15

DECLARATION OF CONFORMITY PAGE 16

*=Mano Record only

LIST OF CONTENTS

GENERAL DESCRIPTION

The KELLER Intelligent Manometer is a precise

pressure measuring instrument. Its high accu-

racy, solid construction and its long battery life

make it to an ideal measuring instrument, espe-

cially for measuring tasks where independence

and flexibility are required.

In its standard version, the pressure transducer

is built into the housing as shown below. The

transducer is retained with a counternut.

Mounting:

Screw the male port of the Intelligent Mano-

meter into the female pressure port and tighten

using the lower hexagon of the transducer.

Adjusting the face:

Loosen the upper hexagon of the counternut

and rotate the Intelligent Manometer to the desi-

red position. Retighten.

The face of the Intelligent Manometer can be

rotated through 355°. This feature allows the

Intelligent Manometer to be mounted in all pos-

sible positions; vertical, horizontal or upside

down.

The splash-proof cover of the Intelligent Mano-

meter is sealed with an O-ring and may easily

be removed by hand by turning the display ring

beyond the limit stop (see “Battery Change” in

Chapter “Notes”

” on page 12).

KELLER

OPERATION

Depressing the front key (marked by a pointed

triangle) sets the Intelligent Manometer into

operation.

After turning on the instrument, all segments of

the display flash three times for operational test.

Between the segment tests, the Intelligent

Manometer displays:

- the measuring range on the upper display

(i.e. 20.00)

- the software program number on the middle

display (MR01)

- the year and calendar week of the program

version (94:23) on the lower right display

KELLER

After this test, the instrument will lead into the

function from which the instrument was pre-

viously turned off.

All commands are selected with the front key.

When the front key is depressed and held, all

commands appear in succession. Releasing

the front key executes the displayed command.

This cycle (constantly depressing the front key

and letting go the key at a desired command) is

subsequently called activation.

MANO-MODE / COMMAND STRUCTURE

The Mano-Mode is the standard mode of the

Intelligent Manometer. Since the function of

secondary displays can be selected (see Dise-

Mode), the individual segments are described

with the peak- and trough pressure display:

The arrow with a flashing minus sign re-

presents a “1”, i.e. at 10bar in the over-

pressure range (here 10.034bar).

The two lower displays can also show the tem-

perature or the time since turn on (more infor-

mation see “Dise-Mode” on page 6/7).

The following commands, appearing in the shown

order, can be activated from the Mano-Mode:

Mano-Mode



EXE resets the peak- and

trough values



OFF turns off the instrument



EXE resets the peak- and

trough values



STEP* leads into the Record-Mode



OFF turns off the instrument



10 / 11 / 12 / 13 (not programmed / no function)



DISE* DIsplay SElect*



16 / 17 (not programmed / no function)



ZERO Permanent Zero Adjust



20 / 21 (not programmed / no function)



RECS* RECord Select*



24 / 25 (not programmed / no function)



SAVS* SAVe Select*



28 / 29 (not programmed / no function)



MECY MEsure CYcle (Adjusting

the measuring cycle)



32 / 33 / 34 … (not programmed / no function)

(The numbers shown are home positions.Activa-

ting these numbers will not execute any command.)

*=Mano Record only













 = Sensor 1 is active

 = HIGH flashes, when maximum pressure

is displayed

 = Peak pressure

 = Actual pressure

 = LOW flashes, when minimum pressure

is displayed

 = Trough pressure

ZERO-MODE

The zero of the system can be adjusted with the

command ZERO.

Activate ZERO.

The display shows:

- Upper display: Actual pressure

- Lower left: ZEro

- Lower right: The actual zero

The zero is now ready to be reset. Activate

ZERO once more for permanent zero reset.

After setting the new zero, the Intelligent Mano-

meter returns to the mode it was prior to activa-

ting the ZERO-command.

Note:

If the above setting was activated by mistake,

turn off the instrument with the command OFF.

When restarting, the instrument will lead into

the Mano-Mode.

The Intelligent Manometer may be supplied fit-

ted with two sensors. Within ZERO, one has the

possibility to switch back and forth between the

two sensors with the command EXE. The arrow

on the upper left display points upwards if sen-

sor 1 is active, downwards if sensor 2 is active.

After the selection of the desired sensor, the

zero of the corresponding sensor can now be

reset by activating the command ZERO.

MECY-MODE

The measuring cycle can be adjusted between

once per second up to once per hour (59:59).

Longer measuring cycles extend the battery life.

STEP

Activate MECY.

The display indicates CYCL

and the lower right shows

the time in minutes and se-

conds.

The first digit flashes.

EXE increases the digits

(1, 2,…5).

STEP switches to the next

digit.

The second digit flashes.

EXE increases the digits

(1, 2,…9) etc.

Activating RES programmes the new selected

measuring cycle and switches back to the Mano-

Mode.

If the peak- and trough pressure are displayed,

the time period set here has no meaning. When

set in peak/trough mode, the instrument will

always measure in a 1/2-second interval.

MECY (MEsure CYcle)= Adjusting the measuring cycle.

DISE-MODE

(MANO RECORD ONLY)

Display Select enables the selection of the dis-

play position, and allocates the measured para-

meter to the chosen display.

There are three selectable display positions:

Upper Display / Lower Left / Lower Right.

These displays can be occupied by the follo-

wing variables:

Symbol Variable

1 Sensor 1

2 Sensor 2 (only if two sensors

are connected)

1-2 Difference (only if two sensors

are connected)

HIGH Peak Value for Sensor 1*

LOW Trough Value for Sensor 1*

25° Temperature

00:00 Time Meter

*If this variable is selected, the

instrument will always measure

in a 1/2-second interval, indepen-

dent from the set measuring cycle.

The selected configuration is valid for both the

Mano-Mode and the Record-Mode.

Please note that not all possible combinations

are programmable.

DISE (DIsplay SElect) = Selection of Display

DISE-MODE

(MANO RECORD ONLY)

Programming of the display:

EXE

STEP

After activating DISE, the instrument displays

the actual settings. The display that is now flas-

hing can be changed by activating EXE.

If another display possibility is to be adjusted,

activate STEP.

When all possibilities are defined to your needs,

you may return to the new configured Mano-

Mode from any position within DISE by activa-

ting RES.

SAVS-MODE

(MANO RECORD ONLY)

The settings programmed in DISE, which are

now active, can be selected for storage under

SAVS. Only the variables which are selected

under SAVS will later actually be stored in the

Record-Mode.

Four different combinations of variables are

offered in the Mano Record. One of the follo-

wing combinations can be selected with the

commmand EXE:

1. Only the variable of the upper display

2. The variable of the upper display and the

lower left display

3. The variable of the upper display and the

lower right display

4. All three variables

Note that the operating hours will never be stored

as an individual variable.

If you have nevertheless selected the operating

hours for storage, they will be neglected during

the storing cycle.

If peak- and trough measurements were selected

for storage, the Record-function will reset the

peak- and trough values after each measure-

ment. Peak- and trough values are monitored

every 1/2 second, the max./min. values occur-

ring during the measurement interval are stored.

RES

EXE

SAVS (SAVe Select) = Selection of the values to be stored in the Record-Mode.

Attention:

Each selected variable requires one storage place! If, for example, three variables are to be

measured, the available place will only last for 300 measurements (with three variables) instead

of 900 measurements with one variable!

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Instrumento de medición de Keller

Keller

Keller ECO 1 Manual de usuario

Keller

Keller CellaTemp PK Series Manual de usuario

Keller

Keller LEO 5 Manual de usuario

Keller

Keller CellaTemp PR11 Manual de usuario

Keller

Keller LEO RECORD Ei Manual de usuario

Keller

Keller CellaCast PA 80-K002 Manual de usuario

Keller

Keller LEO 1 Manual de usuario

Keller

Keller ITS CellaPort PT 11 Series Manual de usuario

Keller

Keller CellaCast PA8 Series Manual de usuario

Keller

Keller CellaTemp PX1 Series Manual de usuario

Keller

Keller EV-97 Manual de usuario

Keller

Keller ITS CellaCast PX 8 Series Manual de usuario

Keller

Keller LEO RECORD Manual de usuario

Keller

Keller Lex 1 Manual de usuario

Keller

Keller ECO 2 Manual de usuario

Keller

Keller LEX 1 Manual de usuario

Keller

Keller dv-2 Manual de usuario

Keller

Keller ECO2-Ei Manual de usuario

Keller

Keller CellaTemp PA 4 Series Manual de usuario

Keller

Keller LEO 5 Manual de usuario

Keller

Keller LEO 1 Manual de usuario

Keller

Keller LEO 1 Manual de usuario

Keller

Keller LEX 1 Ei Manual de usuario

Keller

Keller LEX 1 Ei Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario