Keithley DMM7512 Manual del propietario
Model DMM7512 7½ Digit Sampling Multimeter
Instrument Information
071357601 / October 2018 *P071357601* 1
Introduction
This document describes the DMM7512 7½ Digit Multimeter instrument and how it differs from the Model
DMM7510 7½ Digit Multimeter instrument.
The DMM7512 is a no-front-panel version of the DMM7510 that has two DMM modules housed in one
enclosure. Except for the power switch, each module operates independently within the enclosure.
Figure 1: DMM7512 7½ Digit Multimeter
What you should have received
In addition to the DMM7512, you should have received the items in the following table.
Part number
Description
Quantity
012178100
Test lead kit
4
CA-180-16A
LAN crossover cable, 16 in.
2
1747107XX
Shielded crossover cable with RJ-45 connector, 5 ft.
1
CO-26
Power line cord
1
CS-568-120A
Green and yellow ground cable, 120 in.
1
0713411XX
Safety precautions
1
4299-13 Rack Mount kit, consisting of:
1
▪4076126XX
1U rack rail mount
2
▪10-32X3/8PHTRSH
10-32X3/8 Phillips truss head screw
4
▪10-32X5/8PHTRSH
10-32X5/8 Phillips truss head screw
8
▪FA-274
Cage nut
4
Note: XX is the latest revision number.
Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176 - TestEquipmentDepot.com
Model DMM7512 7½ Digit Sampling Multimeter Instrument Information
2 071357601 / October 2018
Customer documentation
The DMM7512 is very similar to the DMM7510. This document describes the differences between the
DMM7512 and the DMM7510. Other than the changes described in this document, the products are identical,
so you can use the DMM7510 documents as a resource.
For complete customer documentation, see the Model DMM7510 7½ Digit Multimeter Reference Manual and
other DMM7510 documentation.
To download the DMM7510 documentation:
1. Go to tek.com/product-support.
2. Enter the model number.
If you are using Test Script Builder, use the "Model DMM7510 Command Reference" of the TSB help for
information.
The DMM7510 documentation is available from the tek.com/keithley website in Adobe® Acrobat® PDF format
and includes:
▪ The Model DMM7510 Reference Manual: Includes advanced operation topics and maintenance
information. Programmers looking for a command reference, and users looking for an in-depth description
of the way the instrument works (including troubleshooting and optimization), should refer to the Reference
Manual.
▪ The Model DMM7510 User’s Manual: Provides application examples that you can use as a starting point
to create your own applications.
▪ The Model DMM7510 7½ Digit Graphical Sampling Multimeter Calibration and Adjustment Manual:
Provides calibration and adjustment information. Refer to Verification and adjustment (on page 11) for
detail.
▪ Accessories information: Documentation for accessories.
Capabilities and features
The DMM7512 has the following features:
▪ Ability to perform sensitive measurements on low-level signals
▪ Simplified trigger model with measure configuration lists
▪ USB-A connector for flash-drive support
▪ USB-B connector for communication, control, and data transfer
▪ Limit testing with a built-in comparator for pass/fail testing
▪ Digital I/O for stand-alone binning operations or interface to a component handler
▪ SCPI and Test Script Processor (TSP®) programming languages with remote interface ports (USB and
LAN)
▪ Built-in math expressions and user-defined expressions (using a remote interface)
▪ Filtering to reduce reading noise
▪ A trigger model that supports extensive triggering and synchronization schemes at hardware speeds
▪ LXI® Core Specification 1.4 compliance
▪ TSP-Link® system expansion interface that test system builders can use to connect multiple instruments in
a master and subordinate configuration
▪ Supports USB and ethernet local area network (LAN) connections
Model DMM7512 7½ Digit Sampling Multimeter Instrument Information
071357601 / October 2018 3
Differences between the DMM7510 and the DMM7512
The DMM7512 contains two digital multimeters that offer DMM7510 features in a configuration tailored to
rack-mount operation. Most DMM7510 functionality is available, with the following exceptions:
▪ Measure functions for AC voltage, AC current, frequency, period, and capacitance are not available.
▪ The maximum current measurement is 3 A.
▪ There is no front-panel display and there are no keys. You can access a virtual front panel using a remote
LAN interface. Refer to Accessing the virtual front panel (on page 9).
▪ Remote communications setup is different. See Setting up remote communications (on page 7).
▪ Connections for remote communications are on the front panel of the box. See Front-panel overview (on
page 5) for locations.
▪ GPIB functionality is not available.
▪ The Digital I/O connector for each module is oriented so that pin 1 is in the upper right. See Digital I/O port
(on page 6).
▪ The LAN RESET button for each module is on the front panel to the left of the TSP-Link connectors.
▪ Measurement connections are on the rear panel of the instrument only. There is no front terminal or rear
terminal selection. See Rear-panel overview (on page 6) for locations.
▪ The instrument dimensions are different and there are no handles or bumpers. See Dimensions (on
page 4).
▪ The USB VISA resource string for the DMM7512 is USB0::0x05e6::0x7512::[serial
number]::INSTR, where [serial number] is the serial number of the module.
▪ Warmup time for the DMM7512 is four hours.
▪ There is a single power switch and power input for both modules.
▪ Each DMM7512 has three serial numbers, one for the instrument and one for each module. The
instrument serial number is on a label on the front panel. This serial number is not available through a
remote interface. The serial numbers for the modules are on labels on the rear panel. The serial number
for a specific module can be accessed through the virtual front panel or by using the
localnode.serialno command over a remote interface.
▪ The default Command Set for the DMM7512 is TSP instead of SCPI.
Installing the DMM7512
The DMM7512 is intended for mounting in a rack only. For detailed instructions, refer to the documentation for
the Model 4299-13 Rack Mount Kit (part number 0713574XX).
Rack mounting the DMM7512 requires two people. Failure to recognize and observe standard
safety precautions could result in personal injury.
Model DMM7512 7½ Digit Sampling Multimeter Instrument Information
4 071357601 / October 2018
Dimensions
The following figures show the mounting screw locations and other dimensions of the instrument.
Figure 2: DMM7512 top view
Figure 3: Dimensions - front view
Model DMM7512 7½ Digit Sampling Multimeter Instrument Information
071357601 / October 2018 5
Figure 4: Dimensions - side view
Front-panel overview
The front panel of the DMM7512 is shown below. Descriptions of the controls on the front panel follow the
figure.
Figure 5: DMM7512 front panel
Power indicator
and switch
The power switch turns the instrument on or off. The indicator is
illuminated when the instrument is on. The power switch powers both
modules.
USB Type A port
USB Type A connection. You can use a USB flash drive to store
reading buffer data, scripts, and user setups. You can also use it to
upgrade the firmware.
LAN RESET
Reverts the LAN settings and the instrument password to default
values. Insert a straightened paper clip into the hole above LAN
RESET to reset the LAN. Refer to Set the IP address to be set
automatically (on page 8) for details on how to use.
TSP-Link ports
Connections for the TSP-Link® system expansion
interface, which builders of test systems can use to
connect multiple instruments in a master and
subordinate configuration. TSP-Link is a high-speed
trigger synchronization and communication bus.
Model DMM7512 7½ Digit Sampling Multimeter Instrument Information
6 071357601 / October 2018
Digital I/O port
A digital input/output port that detects and outputs digital signals. The
port provides six digital I/O lines. Each output is set high (+5 V) or low
(0 V) and can read high or low logic levels. Each digital I/O line is an
open-drain signal.
USB Type B port
USB Type B connection for communication, control, and data
transfer.
LAN STATUS
LED indicator
Illuminates when the instrument is connected to a local area network
(LAN).
LAN port
Supports full connectivity on a 10 Mbps or 100 Mbps network. The
DMM7512 is a version 1.5 LXI Device Specification 2016 instrument
that supports TCP/IP and complies with IEEE Std 802.3 (ethernet
LAN). See Setting up remote communications (on page 7).
Rear-panel overview
The rear panel of the DMM7512 is shown below. The descriptions of the rear-panel components follow the
figure.
Figure 6: 7512 rear panel
INPUT and
SENSE terminals
Use the INPUT HI and INPUT LO terminals for all
measurements except current. For current
measurements, use the AMPS connection with the
INPUT LO terminal.
Use the SENSE HI and SENSE LO terminals and the
INPUT terminals with the 4-wire resistance, 3-wire
and 4-wire RTD temperature, and DC voltage ratio
functions.
AMPS connection
3 A, 250 V current connector for DC current and digitize DC current
10 µA to 3 A ranges.
Model DMM7512 7½ Digit Sampling Multimeter Instrument Information
071357601 / October 2018 7
Measurement
input fuse
Fast-acting current-input fuse.
For continued protection against fire hazard, replace this fuse with a
fuse of the same type and rating (Keithley part number
DMM7510-FUSE-3A).
EXT TRIG
IN/OUT terminal
This terminal is a TTL-compatible input/output line with a 0 to 5 V
logic signal. You can use this line for triggering by using the transition
of the line state to initiate an action. The instrument can generate
output trigger pulses and detect input trigger pulses on this line.
Chassis ground
Ground screw for connections to chassis ground. This provides
a connection terminal to the equipment frame.
Line fuse and
power receptacle
Connect the line cord to the power receptacle and a grounded AC
power outlet. The line fuse, located just above the power receptacle,
protects the power line input of the instrument.
Setting up remote communications
Each device on a LAN (corporate or private) requires a unique IP address. Contact your corporate information
technology (IT) department for details about obtaining an IP address before you connect the DMM7512 to a
corporate or private network.
Contact your corporate IT department for permission before you connect the DMM7512 to a
corporate network.
Each module in the instrument has a separate IP configuration. The IP configuration persists through a power
cycle.
When the DMM7512 is shipped, the IP configurations for each module are set to Manual and are set to the
following values:
▪ IP address, module 1: 192.168.0.3
▪ IP address, module 2: 192.168.0.4
▪ Gateway: 192.168.0.1
▪ Subnet mask: 255.255.255.0
These values persist through a power cycle unless they are changed or the LAN RESET button is selected. If
the LAN RESET button is selected, the TCP/IP mode is set to automatic.
Model DMM7512 7½ Digit Sampling Multimeter Instrument Information
8 071357601 / October 2018
Set the IP address to be set automatically
When the TCP/IP configuration mode is set to Automatic, a DHCP server automatically sets the IP address,
subnet mask, and the default gateway. To use this option, a DHCP server must be available on the network.
The following steps reset the TCP/IP configuration, which also resets the instrument password. This
allows remote access to LXI web page controls that may have been password-protected before the
reset.
To use the LAN RESET switch to select Automatic configuration:
1. Turn on instrument power.
2. Wait for the instrument to complete power up.
3. Insert a straightened paper clip into the recessed LAN RESET switch on the DMM7512 front panel,
pressing the switch briefly. The LAN status indicator illuminates when the connection is established.
4. To find the IP address that was automatically applied, use the LXI Discovery Tool, a utility that is available
from the Resources tab of the LXI Consortium website (http://www.lxistandard.org/).
Model DMM7512 7½ Digit Sampling Multimeter Instrument Information
071357601 / October 2018 9
Accessing the virtual front panel
If you have a LAN connection, you can access the web interface of each module in the instrument. Each
module has its own IP address and is controlled separately. The web interface for each module includes a
virtual front panel, which you can use to control the module. You can access the web interface for both modules
at the same time.
To access the web interface and virtual front panel:
1. Open a web browser on the host computer.
2. Enter the IP address of the module in the address box of the web browser. For example, the default
address for module 1 is 192.168.0.3, so you enter 192.168.0.3 in the browser address box to access
module 1.
The default IP address for module 2 is 192.168.0.4, so to access module 2, enter 192.168.0.4.
3. Press Enter on the computer keyboard to open the web page for the module.
4. If prompted, enter a user name and password. The default is admin for both.
5. Select Virtual Front Panel from the left pane.
An example of the virtual front panel is shown below.
Figure 7: DMM7512 virtual front panel
Model DMM7512 7½ Digit Sampling Multimeter Instrument Information
10 071357601 / October 2018
Line fuse replacement
A fuse on the DMM7512 rear panel protects the power line input of the instrument.
Disconnect the line cord at the rear panel and remove all test leads connected to the
instrument before replacing a line fuse. Failure to do so could expose the operator to
hazardous voltages that could result in personal injury or death.
The fuse drawer is above the AC receptacle on the rear panel of the DMM7512, as shown in the following
figure.
Figure 8: Fuse replacement
To prevent injury, death, or instrument damage, use only the correct fuse type (see table).
To replace the line fuse:
1. Power off the instrument and remove the line cord.
2. There is a small tab at the bottom of the fuse drawer. Using a small screwdriver, pry this tab from the AC
receptacle.
3. Slide the fuse drawer out to access to the fuse.
4. Snap the fuse out of the drawer and replace it with the same type, as specified in the table below.
5. Push the fuse drawer back into the module.
If a fuse continues to become damaged, a circuit malfunction exists and must be corrected. Return the
instrument to Keithley Instruments for repair.
Line fuse
Line voltage
Rating
Keithley part number
100 V to 240 V
250 V, 3.15 A, Slow Blow 5 x 20 mm
FU-106-3.15
Tabla de contenidos
Otros manuales de Multímetro de Keithley
Keithley
Keithley 195A Manual de usuario
Keithley
Keithley 177 Manual de usuario
Keithley
Keithley 2016 Manual de usuario
Keithley
Keithley 2000 Manual de usuario
Keithley
Keithley 2110 Manual de uso y cuidado
Keithley
Keithley 2110 Manual de usuario
Keithley
Keithley DMM7510 Manual de uso y cuidado
Keithley
Keithley 2700 Manual de usuario
Keithley
Keithley 169 Manual de usuario
Keithley
Keithley DMM6500 Manual de usuario
Keithley
Keithley 197 Manual de usuario
Keithley
Keithley 2010 Manual de usuario
Keithley
Keithley 1765 Manual de usuario
Keithley
Keithley DMM7510 Manual de uso y cuidado
Keithley
Keithley 160B Manual de usuario
Keithley
Keithley 2750 Manual de usuario
Keithley
Keithley 164 Manual de usuario
Keithley
Keithley 191 Manual de usuario
Keithley
Keithley 2001-TCSCAN Manual de usuario
Keithley
Keithley 2110-100 Manual de uso y cuidado
Manuales populares de Multímetro de otras marcas
Gossen MetraWatt
Gossen MetraWatt METRAmax 6 Manual de usuario
PeakTech
PeakTech 4000 Manual de uso y cuidado
YOKOGAWA
YOKOGAWA 90050B Manual de usuario
Gossen MetraWatt
Gossen MetraWatt METRALINE DMM16 Manual de usuario
Fluke
Fluke 8846A Manual de operación y mantenimiento
Tempo Communications
Tempo Communications MM200 Manual de usuario
