KANSAI SPECIAL BK-20 Manual de usuario

INSTRUCTION

Industrial Sewing Machines

First published : March 1992

3rd edition : July 2018

No. 180038

BELT LOOP CUTTER

BK-20

BK-20 Instruction Manual

INTRODUCTION

Thank you for your purchasing Kansai Special's BK-20 belt loop cutting

attachment.

This unit is designed to operate with the Kansai Special DVK-1702B,

DVK-1702BK, B-2000, or B-2000C machines. It may be coupled with a newly

purchased machine or it may be coupled with a machine in current operation.

The BK-20 has a maximum production rate of 200 pieces per minute, dependant

upon the length of the belt loop. Read and study this instruction manual

carefully before beginning any of the procedures and save it for later use.

1. This instruction manual describes adjustments and maintenance procedures on this

machine.

2. Before starting the machine, check to make sure the pulley cover, safety cover, etc.

are secured.

3. Before adjusting, cleaning, threading the machine or replacing the needle, be sure to

turn off the power.

4. Never start the machine with no oil in the reservoir.

5. Refer to the parts list as well as this instruction manual before performing

preventive maintenance.

6. The contents described in this instruction manual are subject to change without

notice.

I n d i c a t i o n o f s e r i a l n u m b e r

Model

Zip code

1 8 0 0 0 0 1

The date of manufacture

Year of 2018

Serial number

CONTENTS

1. SPECIFICATIONS ············································· 1

2. ASSEMBLY AND INSTALLATION ······················ 1

3. BELT LOOP MATERIAL PATH ··························· 2

4. OPERATION ······················································ 2

5. PRODUCTION RATE CALCULATIONS ··············· 3

6. TO SHARPEN THE KNIFE ································· 3

7. TABLETOP SPECIFICATIONS ··························· 4

【1】SPECIFICATIONS

1. Power source : Available in the following voltages

(all AC single phase)100，115-120，200，220-240

2. Motor ･････････････････････････

25W

3. Installation style ･･･････････････ Directly on the tabletop or separate table

4. Cutting rate (production rate) ･･･ Up to 200 cuts per minute

5. Size range of belt loops

･･････････

50~150mm

6. Maximum cutting width ････････

30mm

7. Production counter ･････････････

0~9999 pieces

【2】ASSEMBLY AND INSTALLATION

■Contents of the carton

1. BK-20 cutting head ･･･ 1

2. Tensioner ････････････ 1

3. Mounting plate ･･･････ 1

4. Hardware

Bolt

Nut

M6×55 ･･･ 4 Pieces

M6 Nut

････

4 Pieces

M6×15 ･･･ 4 Pieces

M6 Washer

･･ 4 Pieces

M5×10 ･･･ 2 Pieces

■Assemble the unit according to the following

simple directions, using figure as a guide.

1. Attach the mounting plate to the tabletop

using the M6×55 bolts, M6 washers, and

M6 nuts supplied. The position of the

unit is determined by the position of the 4

mounting holes which must be drilled in

the tabletop as shown in tabletop

specifications.

2. Attach the cutting head to the far end of

the mounting plate using the M6 ×15

screws supplied.

3. Attach the tensioner to the mounting plate

between the machine head and the cutting

head using the M5×10 screws supplied.

4. Connect the power cord.

< Note >

As a safety feature, the BK-20 cutting head will not operate if the front cover is not fully

latched closed. Also, the BK-20 is equipped with a tension meter which automatically

stops the cutting operation if the supply of belt loop material is stopped (The BK-20 stops

cutting when the sewing is finished.)

【3】BELT LOOP MATERIAL PATH

1. Making sure that the BK-20 cutting head is switched off, sew out approximately

1metre (3 feet) of belt loop material.

2. Set the belt loop material through the tensioner and cutting head following the path

shown in figure.

【4】OPERATION

1. Switch on the power.

2. Sew as usual. The BK-20 will follow the sewing

rate of the machine.

3. To adjust or change the cutting length, follow the

procedures below

a. Switch off the power.

b. Loosen the nut 1 and turn the adjusting screw 2

right or left to set the desired length of cut.

Turning the screw to the right (clockwise)

increases the length of cut. Turning the screw

to the left (counterclockwise) decreases the

length of the cut.

c. Retighten the nut. Never operate the BK-20

while this nut is loose.

d. Shut the front cover and switch on the power.

e. Sew a bit of belt loop material and allow the

BK-20 to cut two or three pieces of belt loops.

Measure the length of the pieces to determine if the length is correct.

f. Repeat procedures a through e until the desired belt loop length is attained.

4. Proceed sewing as usual. The BK-20 will follow the speed of the sewing head up to a

maximum rate of 200 pieces per minute.

5. For safety reasons, do not operate the BK-20 without material.

6. To maintain record of the production quantity, reset the production counter to “0000”

at the start of the operation.

< Note >

Before replacing the knife, be sure to turn off the machine.

【5】PRODUCTION RATE CALCULATIONS

The following calculation will allow you to determine your production rate according to the

machine speed, the stitch density or stitch length, and belt loop cut length.

■Calculate the production rate as follows

1. Machine speed (stitches per minute)

＝Sewn unit length (inches per minute)

Stitch density (stitches per inch)

2. Sewn unit length (inches per minute)

＝Production qty (Pieces per minute)

Loop cut length (inches per piece)

■Example

If the machine speed is 4,000rpm, the stitch density is 8 stitches per inch, and the belt loop

cut length is 3.5 inches

4,000 stitches per minute

＝500 inches per minute

8 stitches per inch

500 inches per minute ＝143 pieces per minute

3.5 inches per piece

【6】TO SHARPEN THE KNIFE

■When the knife become dull, sharpen the knife or replace the new knife.

When the knife replacing, do not loose the knife mount bracket.

The knife mount bracket is factory-set for standard.

【7】TABLETOP SPECIFICATIONS

Tabla de contenidos

Otros manuales de Máquina de coser de KANSAI SPECIAL

KANSAI SPECIAL

KANSAI SPECIAL PX302-4W Manual de usuario

KANSAI SPECIAL

KANSAI SPECIAL SX Series Manual de usuario

KANSAI SPECIAL

KANSAI SPECIAL DFB1412PS Manual de usuario

KANSAI SPECIAL

KANSAI SPECIAL RX/UTC Series Manual de usuario

KANSAI SPECIAL

KANSAI SPECIAL DLR-1501SPF Manual de usuario

KANSAI SPECIAL

KANSAI SPECIAL JJ Series Manual de usuario

KANSAI SPECIAL

KANSAI SPECIAL RX9701J Series Manual de usuario

KANSAI SPECIAL

KANSAI SPECIAL BX Series Manual de usuario

KANSAI SPECIAL

KANSAI SPECIAL DLR Series Manual de usuario

KANSAI SPECIAL

KANSAI SPECIAL NC Series Manual de usuario

KANSAI SPECIAL

KANSAI SPECIAL DFB Series Manual de usuario

KANSAI SPECIAL

KANSAI SPECIAL RX series Manual de usuario

KANSAI SPECIAL

KANSAI SPECIAL UF Series Manual de usuario

KANSAI SPECIAL

KANSAI SPECIAL DWK-1803D Manual de usuario

KANSAI SPECIAL

KANSAI SPECIAL WX8803/UTC Manual de usuario

KANSAI SPECIAL

KANSAI SPECIAL LX-SP Series Manual de usuario

KANSAI SPECIAL

KANSAI SPECIAL DFB1404P Manual de usuario

KANSAI SPECIAL

KANSAI SPECIAL HDX Series Manual de usuario

KANSAI SPECIAL

KANSAI SPECIAL WX Series Manual de usuario

KANSAI SPECIAL

KANSAI SPECIAL V 7100 Series Manual de usuario

KANSAI SPECIAL

KANSAI SPECIAL SX Series Manual de usuario

KANSAI SPECIAL

KANSAI SPECIAL DVC-200 SERIES Manual de usuario

KANSAI SPECIAL

KANSAI SPECIAL DVK1702B Manual de usuario

KANSAI SPECIAL

KANSAI SPECIAL DFB MR-S Series Manual de usuario

Manuales populares de Máquina de coser de otras marcas

Riccar

Riccar RL634DE Manual de usuario

Singer

Singer 2517 Manual de usuario

Pfaff

Pfaff 3307-1 SERIES Manual de usuario

Janome

Janome Quilt Maker Pro 18 VERSA Manual de usuario

Siruba

Siruba C007JP Manual de usuario

Husqvarna Viking

Husqvarna Viking Designer SE Manual de usuario

Singer

Singer 148-5 Manual de usuario

IKEA

IKEA SY Manual de usuario

Pfaff

Pfaff 571 Manual de usuario

Singer

Singer 15-91 Manual de usuario

Brother

Brother BB370 Manual de usuario

Pegasus

Pegasus WT100 Series Manual de usuario

Reliable

Reliable 7100DB Manual de usuario

Pfaff

Pfaff 937 Manual de usuario

Singer

Singer 6038 Manual de usuario

Singer

Singer 413K Manual de usuario

Pfaff

Pfaff 1471 E1 Manual de usuario

Kenmore

Kenmore 16677 - Serger Sewing Machine Manual de usuario