EN | M6500K
Marten defence for an in the
engine compartment incl. safety hood switch
... chases away martens with high-voltage plates electrically
chargedto200 - 300 V by electric shock intheenginecompartment
of the motor vehicle (only weak surges that only chase away the
ultrasonic sounds.
Further advantages:
•
• ± 0.3 V monitor)
• The stainless steel contact plates can be placed at any point of
•
•
no longer monitored by the car electronics and the motor is
• terminal 15 is no longer necessary, which
• high voltage when the hood is opened.
• Also suitable for cars with CAN bus.
To be observed:
• Themartenscarershould be installedby a specialistworkshop.
• Secure all lines so that they cannot come into contact with
excluded, too.
• Important: The high-voltage contact plates have to be
assembled in such a manner that the uninsulated contact
plates are > 10 mm away from other live contacts in the car.
Furthermore,theuninsulatedcontactsurfaceshouldnottouch
other parts either (risk of short-circuit). This also applies to
• is to be avoided. Fix the plates in such a way that the water can
• Subject to technical changes.
Scope of supply:
• 1basicdevicewithbuilt-inloudspeakerandcompactconnector
• 1 cable set with compact coupling and Ňying fuse holder with
inserted fuse 1A
• 1 engine hood switch
• 1 fastening screw for the engine hood switch 4.2 x 16
•
• 5 stainless steel contact plates and holder
• 5 stainless steel screws
To be observed before
must be between 11...13.4 V. The high-voltage plates should lie
incorporated in the module should Ňash shortly at an interval of
isokay and maybe installed.During thetestplease make surenotto
touch the high-voltage plates!
capacitor in the control unit and the contact plates is interrupted.
General assembly
Please remove the fuse of the device from the fuse holder during
the assembly.
Installthebasicdeviceinadryplaceinthecarwhereitwon’tgettoo
hot (please not in the immediate vicinity of the exhaust manifold or
ultrasonic sounds
can spread well in the engine compartment
cable with the built-in fuse holder to “+ 12 V” and the earth cable to
the vehicle ground or “- 12 V”.
Ultrasonicsoundsspreadlikelight,thereare„shadows“(noultrasonic
sounds) behind obstacles. Therefore, the loudspeaker in the device
should radiate on the places at risk of being (within the cone
Lay the high-voltage cable in the engine compartment in such a
mannerthatthecontactplatescanbemountedattheplacesatrisk
of being . The high-voltage cable should not directly go past
could melt).
The high-voltage plates can be mounted anywhere on the high-
voltage cable. The high voltage cable can be recognized by the fact
thatitisbyfarthelongestcableatthemartenscarer(approx.4.5m).
The rectangular high-voltage plates have 3 holes each and can be
lengthwise and crosswise to the cable route as well as in 3
on the support brackets and thus can
be individually adjusted to the in the motor. In this
way, hollow spaces in the engine compartment can be
covered.The marten‘s pathsbecome„narrowed“,a contactwiththe
high voltage becomes unavoidable.
Please make sure that the high-voltage cable is routed through the
high-voltagecables,use thethinhole,forthickerhigh-voltage cables
use the thicker cross hole in the contact plate holder. The screw for
fastening the high-voltage plate is then inserted through the bore of
the high-voltage plate into the bore of the high-voltage plate holder
under which the cable is passed, as shown in the drawing. When
screwing together, the screw pierces the high-voltage cable and
and the high-voltage cable.
The contact plates in the motor, which have been completely
that the cable with the high-voltage plates is laid in the car so that
the cable end ends at the engine hood switch. The engine hood
switchis theninstalledin such a way thatit getsan electricalcontact
to the vehicle earth via the fastening screw. The plug for the engine
hood switch and the cable end of the high-voltage cable must be
crimped together. In case of a correct assembly, the high voltage in
the high-voltage cable is short-circuited to the car chassis via the
engine hood switch when opening the engine hood. If the fastening
screw at the engine hood switch cannot be screwed into the car
this, place a screw eye under the screw and connect it to the car
chassis using a cable.
yellow warning adhesive label
High Voltage!“ in a well visible place in the engine compartment
Seite 5 von 6 12024DI / K&K M6500K / KV030 / Bogen-2018
