Kaisai XK60 Manual de usuario
XK60 WIRED CONTROLLER
OWNER”S MANUAL
User Notice
Please carefully read this manual before installation and use of this product.
Thanks for choosing FGPOLAND duct type air conditioners. Please read this manual
carefully before operating this product and keep it properly for future reference. In
addition, please take notice of the symbols below.
WARNING!
This mark indicates procedures which, if improperly performed, might lead to
the death or serious injury of the user.
CAUTION!
This mark indicates procedures which, if improperly performed, might possibly
result in personal harm to the user, or damage to property.
CAUTION!
Do not install the wired controller in the damp place or under direct sunlight.
Do not beat, toss, or frequently assemble/disassemble the wired controller.
Do not operate the wired controller with wed hands and never let any liquid flow into it.
Do not install or remove the wired controller by yourself. If necessary, please contact the after-sales
serviceman.
This wired controller is applicable to various kinds of air conditioners, while some specific functions
unavailable to the duct type air conditioners will not be covered in this manual.
Before operating the air conditioner, please read this manual carefully and keep it properly for future
reference.
2kaisai.com
3
kaisai.com
Wired Controler XK60
1
1 Introduction to the Wired Controller
Fig.1 Appearance of the Wired Controller
1.1 Appearance and LCD Icons
Fig.2 Appearance of the LCD
Wired Controler XK60
2
1.2 Introduction to the LCD Icons
Table 1
No. Icons Introduction
1Left and right swing function
2Up and down swing function
3Air exchange function
4 Sleep function
5Auto mode
6COOL mode
7DRY mode
8FAN mode
9HEAT mode
10 Health function
11 I-Demand function
12 Vacation function
13 Status display of master and slave wired controller
14
Shield function
The button operation, temperature setting, "On/Off" operation, "Mode"
setting, and "Save" setting are disabled.
15 Fan speed
16 Memory function
The unit will resume the original setting state after power recovery.
17 Turbo function
18 Energy-saving function
19 Ambient/setting temperature
4kaisai.com
Wired Controler XK60
3
20 Electric heater
21 Blow function
22 Defrosting function
23 Filter cleaning
24 Timer Setting
25 Keycard control / Detected status sensed by human body
26 Quiet function
27 Lock function
2 Press Buttons
2.1 Buttons
Fig.3 Press Buttons
2.2 Instruction to the Function of Press Buttons
Table 2
No. Press Buttons Function Introduction
1 Enter/Cancel Function selection and canceling;
Press it for 5s to enquiry the outdoor and indoor ambient temperature.
2 ▲Running temperature setting of indoor unit, range :16~30°C
Timer setting, range:0.5-24hr
Air function setting
Save setting
Clean setting
6 ▼
5
kaisai.com
Wired Controler XK60
4
3 Fan Select fan speed from high, mid-high, middle, mid-low, low and auto
levels.
4 Mode Selection of the COOL, HEAT, FAN, Auto or DRY mode.
5 Function
Switchover among these functions of
SWING/AIR/SLEEP/HEALTH/I-DEMAND/VACATION/TURBO/SAVE/E-H
EATER/BLOW/QUIET
7 Timer Timer setting
8 On/Off Turn on/off indoor unit
4 mode
and 2 ▲ Memory
Press Mode and ▲ at the same time for 5s under the OFF state of the unit
to activate/deactivate memory function (If memory is set, indoor unit will
resume original setting state after power recovery. If not, indoor unit is
defaulted to be OFF after power recovery. Memory function is defaulted to
be ON)
2 ▲
and 6 ▼ Lock
Under the ON state of the unit without any malfunction or under the OFF
state of the unit, press ▲and ▼ buttons at the same time for 5s to go to
the lock state. In this case, any other buttons won’t respond the press.
Repress ▲ and ▼ again for 5s to quit the lock state.
4 mode
and 6 ▼ °F/°C Under the OFF state of the u
nit, press the Mode and ▼ at the same time
for 5s to switch the temperature scale between Celsius and Fahrenheit.
3 OPERATION INSTRUCTION
3.1 On/off
Press the On/Off button to turn on or off the unit.
Notes:
①The state shown in Fig.4 indicates the OFF state of the unit after energization.
②The state shown in Fig.5 indicates the ON state of the unit after energization.
Fig.4 OFF State of the Unit Fig.5 ON State of the Unit
6kaisai.com
Wired Controler XK60
5
3.2 Mode Setting
Under the ON state of the unit, press the Mode button to switch the operation
modes as the sequence shown in Fig.6:
Fig.6
3.3 Temperature Setting
Press ▲ or ▼button to increase or decrease setting temperature under on-state of
the unit. If press either of them continuously, temperature will be increased or
decreased by 1°C every 0.5s.
In Cooling, Dry, Fan and Heating mode, temperature setting range is 16°C~30°C.
In Auto mode, the setting temperature is un-adjustable.
As shown in Fig.7:
Fig.7 Temperature Setting
7
kaisai.com
Wired Controler XK60
6
3.4 Fan Speed Setting
Press Fan button, fan speed of indoor unit will change as the sequence shown in
Fig.8:
Fig.8 Fan Speed Setting
3.5 Right and Left Swing
Under the ON state of unit, press the Function button to select the “Right and Left
Swing” function option and then press the Enter/Cancel button to activate it.
When the Swing function is activated, press the Function button to select the
"Right and Left Swing" function option and then press the Enter/Cancel button to
deactivate it.
Right and Left Swing function setting is as shown in Fig.9.
8kaisai.com
Wired Controler XK60
7
Fig.9 Right and Left Swing Setting
3.6 Up and Down Swing
Under the ON state of unit, press the Function button to select the "Up and Down
Swing" function option and then press the Enter/Cancel to activate it.
When the Swing function is activated, press the Function button to select the "Up
and Down Swing" function option and then press the Enter/Cancel button to deactivate
it.
Up and Down Swing function setting is as shown in Fig.10.
9
kaisai.com
Wired Controler XK60
8
Fig.10 Up and Down Swing Setting
3.7 Timer Setting
Timer “On” Setting:
It is intended to set when to start the unit. When the unit is OFF, press the Timer
button, with xx. Hour displayed and ON blinking, then press ▲/▼ to adjust the timer,
after that, press the Timer button again to make a confirmation. If the Mode button is
pressed prior to the confirmation, it will switch to the Timer Off setting. After the timer
Off setting, the LCD displays xx. Hour ON OFF, xx. Hour indicating the time to start the
unit, while the time to stop the unit won’t be displayed.
Timer “Off” Setting:
It is intended to set when to stop the unit. When the unit is On, press the Timer
button, with xx. Hour displayed and OFF blinking, then press ▲/▼to adjust the timer,
after that, press the Timer button again to make a confirmation. If the Mode button is
pressed prior to the confirmation, it will switch to the Timer On setting. After the timer
On setting, the LCD displays xx. Hour ON OFF,xx. Hour indicating the time to stop the
unit, while the time to start the unit won’t be displayed.
Cancellation of Timer Setting: The timer setting can be canceled by press “Timer”.
Then , xx. Hour won’t be displayed.
10 kaisai.com
