JVC GV-DS2 Manual de usuario
GV-DS2
JLIP VIDEO CAPTURE DOCKING STATION
GV-DS2
BASE DE MONTAGE A CAPTURE VIDEO JLIP
ENGLISHFRANÇAIS
INSTRUCTIONS
MODE D'EMPLOI
LYT0002-0W2A
COPYRIGHT© 1997 VICTOR COMPANY OF JAPAN, LTD. UPrinted in Japan
0997MSV*UN*YP
JVC COMPANY OF AMERICA
DIVISION OF US JVC CORP.
41 Slater Drive, Elmwood Park, N.J. 07407
JVC CANADA INC.
21 Finchdene Square, Scarborough Ontario M1X 1A7
For Customer Use:
Enter below the Model No. and Serial
No. which is located on the bottom of
cabinet. Retain this information for
future reference.
Model No.
Serial No.
2EN
SAFETY
PRECAUTIONS
Dear Customer,
Thank you for purchasing this VIDEO CAPTURE
DOCKING STATION. Before use, please read the
safety information and precautions contained in the
following pages to ensure safe use of this product.
Using This Instruction Manual
• All major sections and subsections are listed in the
Table Of Contents (Zpg. 7 – 9).
• Notes appear after most subsections. Be sure to read
these as well.
• Basic and advanced features/operation are separated for
easier reference.
It is recommended that you . . .
.... refer to “Controls and Connectors” (Zpg. 12) and
familiarize yourself with connector locations before
use.
.... read thoroughly the Safety Precautions and Safety
Instructions that follow. They contain extremely
important information regarding the safe use of your
new VIDEO CAPTURE DOCKING STATION.
CAUTION:
TO REDUCE THE RISK OF FIRE,
DO NOT REMOVE COVER (OR
BACK). NO USER–SERVICEABLE
PARTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE
PERSONNEL.
You are recommended to carefully read the cautions
on pg. 5 and 6 before use.
Declaration of Conformity
Model Number : GV-DS2U
Trade Name : JVC
Responsible party : US JVC CORP.
Address : 41 Slater Drive, Elmwood Park,
N. J. 07407
Telephone Number : (201) 794–3900
This device complies with Part 15 of FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.
Change or modifications not approved by the party
responsible for compliance could void the user’s
authority to operate the equipment. This equipment has
been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will
not occur in a particular installation.
If this equipment does cause harmful interference to
radio or television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.
Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV
technician for help.
WARNING:
TO PREVENT FIRE OR SHOCK
HAZARD, DO NOT EXPOSE
THIS UNIT TO RAIN OR
MOISTURE.
When using the Video Capture Docking Station, use
the AA-V90U AC Adapter/Charger (optional or
provided with the camcorder).
NOTE:
The rating plate (serial number plate) and safety
caution are on the bottom of the VIDEO CAPTURE
DOCKING STATION.
This Class B digital apparatus meets all requirements
of the Canadian Interference – Causing Equipment
Regulations.
“Cet appareil numérique de la classe B respecte toutes
les exigences du Règlement sur le matériel brouilleur
du Canada.”
EN 3
ANTENNA INSTALLATION
INSTRUCTIONS
1. Outdoor Antenna Grounding
If an outside antenna or cable system is connected to the
product, be sure the antenna or cable system is grounded
so as to provide some protection against voltage surges
and built-up static charges. Article 810 of the National
Electrical Code, ANSI/NFPA 70, provides information
with regard to proper grounding of the mast and
supporting structure, grounding of the lead-in wire to an
antenna discharge unit, size of grounding conductors,
location of antenna discharge unit, connection to
grounding electrodes, and requirements for the grounding
electrode.
2. Lightning
For added protection for this product during a lightning
storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will prevent
damage to the product due to lightning and power-line
surges.
3. Power Lines
An outside antenna system should not be located in the
vicinity of overhead power lines or other electric light or
power circuits, or where it can fall into such power lines
or circuits. When installing an outside antenna system,
extreme care should be taken to keep from touching such
power lines or circuits as contact with them might be
fatal.
IMPORTANT PRODUCT
SAFETY INSTRUCTIONS
Electrical energy can perform many useful functions. But
improper use can result in potential electrical shock or
fire hazards. This product has been engineered and
manufactured to assure your personal safety. In order not
to defeat the built-in safeguards, observe the following
basic rules for its installation, use and servicing.
ATTENTION:
Follow and obey all warnings and instructions marked on
your product and its operating instructions. For your
safety, please read all the safety and operating instructions
before you operate this product and keep this manual for
future reference.
INSTALLATION
1. Grounding or Polarization
Your product may be equipped with a polarized
alternating-current line plug (a plug having one blade
wider than the other). This plug will fit into the power
outlet only one way. This is a safety feature.
If you are unable to insert the plug fully into the outlet, try
reversing the plug. If the plug should still fail to fit,
contact your electrician to replace your obsolete outlet.
Do not defeat the safety purpose of the polarized plug.
2. Power Sources
Operate your product only from the type of power source
indicated on the marking label. If you are not sure of the
type of power supply to your home, consult your product
dealer or local power company. If your product is
intended to operate from battery power, or other sources,
refer to the operating instructions.
3. Overloading
Do not overload wall outlets, extension cords, or integral
convenience receptacles as this can result in a risk of fire
or electric shock.
4. Power Cord Protection
Power supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon
or against them, paying particular attention to cords at
plugs, convenience receptacles, and the point where they
exit from the product.
5. Ventilation
Slots and openings in the cabinet are provided for
ventilation. To ensure reliable operation of the product
and to protect it from overheating, these openings must
not be blocked or covered.
• Do not block the openings by placing the product on a
bed, sofa, rug or other similar surface.
• Do not place the product in a built-in installation such
as a bookcase or rack unless proper ventilation is
provided or the manufacturer’s instructions have been
adhered to.
6. Wall or Ceiling Mounting
The product should be mounted to a wall or ceiling only
as recommended by the manufacturer.
ANTENNA
LEAD IN WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION
810-20)
GROUNDING
CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING ELECTRODE SYSTEM
(NEC ART 250. PART H)
NEC – NATIONAL ELECTRICAL CODE
ELECTRIC SERVICE
EQUIPMENT
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE, ANSI/NFPA 70
GROUND CLAMP
4EN
USE
1. Accessories
To avoid personal injury:
•Do not place this product on an unstable cart,
stand, tripod, bracket or table. It may fall,
causing serious injury to a child or adult, and
serious damage to the product.
•Use only with a cart, stand, tripod, bracket, or
table recommended by the manufacturer or sold
with the product.
•Use a mounting accessory recommended by the
manufacturer and follow the manufacturer’s
instructions for any mounting of the product.
•Do not try to roll a cart with small casters across
thresholds or deep-pile carpets.
2. Product and Cart Combination
A product and cart combination should be moved
with care. Quick stops, excessive force, and
uneven surfaces may cause the product and cart
combination to overturn.
3. Water and Moisture
Do not use this product near
water—for example, near a
bath tub, wash bowl, kitchen
sink or laundry tub, in a wet
basement, or near a swim-
ming pool and the like.
4. Object and Liquid Entry
Never push objects of any kind into this product
through openings as they may touch dangerous
voltage points or short-out parts that could result in
a fire or electric shock. Never spill liquid of any
kind on the product.
5. Attachments
Do not use attachments not recommended by the
manufacturer of this product as they may cause
hazards.
6. Cleaning
Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.
7. Heat
The product should be situated away from heat
sources such as radiators, heat registers, stoves, or
other products (including amplifiers) that produce
heat.
SERVICING
1. Servicing
If your product is not operating correctly or
exhibits a marked change in performance and you
are unable to restore normal operation by
following the detailed procedure in its operating
instructions, do not attempt to service it yourself as
opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all
servicing to qualified service personnel.
2. Damage Requiring Service
Unplug this product from the wall outlet and refer
servicing to qualified service personnel under the
following conditions:
a. When the power supply cord or plug is
damaged.
b. If liquid has been spilled, or objects have fallen
into the product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operating
instructions as an improper adjustment of other
controls may result in damage and will often
require extensive work by a qualified technician
to restore the product to its normal operation.
e. If the product has been dropped or damaged in
any way.
f. When the product exhibits a distinct change in
performance—this indicates a need for service.
3. Replacement Parts
When replacement parts are required, be sure the
service technician has used replacement parts
specified by the manufacturer or have the same
characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock or
other hazards.
4. Safety Check
Upon completion of any service or repairs to this
product, ask the service technician to perform
safety checks to determine that the product is in
safe operating condition.
PORTABLE CART WARNING
(Symbol provided by RETAC)
EN 5
CAUTIONS
DO NOT attempt to insert foreign objects into the connectors, as this can lead
to electric shock or fire. If an object is accidentally inserted, unplug it and
contact your JVC dealer. Be especially careful with children.
If during use you notice that the VIDEO CAPTURE DOCKING STATION is
damaged, unplug it and contact your JVC dealer. Use of the VIDEO CAPTURE
DOCKING STATION under these conditions can lead to fire or electric shock.
DO NOT attempt to repair or modify the VIDEO CAPTURE DOCKING
STATION. Doing so may result in malfunctions or injury. If a problem occurs,
contact your JVC dealer.
Failure to heed the following precautions may result in damage to the VIDEO
CAPTURE DOCKING STATION.
1. DO NOT place the VIDEO CAPTURE DOCKING STATION . . .
.... in an environment prone to extreme temperatures or humidity.
.... in direct sunlight.
.... in a dusty environment.
.... in an environment where strong magnetic fields are generated.
.... on a surface that is unstable or subject to vibration. The unit may fall, causing injury.
2. DO NOT place heavy objects on the VIDEO CAPTURE DOCKING STATION.
3. DO NOT place anything which might spill on top of the VIDEO CAPTURE DOCKING
STATION.
4. AVOID violent shocks to the VIDEO CAPTURE DOCKING STATION during transport.
5. DO NOT leave the VIDEO CAPTURE DOCKING STATION plugged in when the unit is not
in use.
6. DO NOT use accessories other than those designated in the instructions. Use of others can
lead to fire or electric shock.
7. DO NOT connect devices to the VIDEO CAPTURE DOCKING STATION other than those
designated in the instructions. Use of others can lead to malfunctions.
6EN
CAUTIONS
(cont.)
How to handle a CD-ROM
●Take care not to soil or scratch the mirror surface (opposite to the printed surface). Do not
write anything or put a sticker on either the front or back surface. If the CD-ROM gets dirty,
gently wipe it with a soft cloth outward from the center hole using a circular motion.
●Do not use conventional disc cleaners or cleaning spray.
●Do not bend the CD-ROM or touch its mirror surface.
●Do not store your CD-ROM in a dusty, hot or humid environment. Keep it away from direct
sunlight.
MAINTENANCE
If the inside of the VIDEO CAPTURE DOCKING STATION is left dusty for a long time, its use
can lead to fire or malfunction. Consult your JVC dealer on cleaning.
CAUTION:
Changes or modifications not approved by JVC could void user’s authority to operate the
equipment.
●The Readme.TXT file provides additional information for setup and information that is not
included in the instruction manual. Please read the file before installing the provided
software program.
●You can find the latest information (in English) on the provided software program at our
www server.
<www>http://www.jvc-victor.co.jp/index-e.html
EN 7
CONTENTS
MAJOR FEATURES 10
CONTROLS AND CONNECTORS 12
CAMCORDER ATTACHMENT 13
CONNECTIONS 14
JLIP VIDEO CAPTURE SOFTWARE SECTION .......
17
GETTING STARTED 18
INSTALLATION (JLIP Video Capture Software) 19
OPEN & CLOSE (Basic Operation Procedure) 20
Preparation ....................................................................... 20
How to close the program ...................................................... 21
INITIALIZATION 22
Initializing JLIP .................................................................. 22
Select units........................................................................ 23
HOW THE DESKTOP WORKS 24
Main desktop window........................................................... 24
Menu bar .......................................................................... 26
Each pulldown menu is configured as follows ................................ 26
VIDEO CAPTURE 28
Capturing video images ......................................................... 28
Step by step capture............................................................. 29
Automatic capture................................................................ 30
Program capture ................................................................. 30
Interval capture .................................................................. 32
PICTURE FORMAT SETTING 33
Selecting a picture format....................................................... 33
ADDITIONAL OPERATIONS 34
Counter value change ............................................................ 34
Counter reset ..................................................................... 34
Delete index image and full image............................................. 35
Change ID ......................................................................... 35
8EN
CONTENTS
(cont.)
SAVE PICTURE 36
Create new folder ................................................................ 36
Saving ............................................................................. 36
Open index........................................................................ 37
Save the full image data ........................................................ 37
JLIP VIDEO PRODUCER SOFTWARE 38
Using JLIP video producer software data..................................... 38
How to store JLIP video producer software data ........................... 39
TROUBLESHOOTING 40
LIST OF ERROR MESSAGES 42
JLIP VIDEO PRODUCER SOFTWARE SECTION .....
45
GETTING STARTED 46
INSTALLING (JLIP Video Producer Software) 47
STARTING JLIP VIDEO PRODUCER SOFTWARE 48
VIDEO PRODUCER WINDOW BUTTONS AND DISPLAYS 50
BASIC OPERATIONS 52
Operating camcorder............................................................. 52
Setting in/out points ............................................................ 52
Playing back one programmed scene .......................................... 53
Playing back all programmed scenes .......................................... 53
Dubbing............................................................................ 54
Saving the program list on hard disk .......................................... 55
Opening a saved file ............................................................. 56
Correcting and cutting the programmed counter date ....................... 56
Overwriting the file ............................................................. 57
Selecting a P.AE/Effect .......................................................... 58
Selecting a Fade/Wipe Effect................................................... 58
VIDEO PRINTER WINDOW BUTTONS AND DISPLAYS 60
EN 9
VIDEO PRINTER OPERATION (GV-PT1U) 62
Printing ............................................................................ 62
Adjusting picture equalization .................................................. 63
Quitting the “Video Printer” window......................................... 63
Quitting the JLIP VIDEO PRODUCER window ................................ 63
VIDEO PRINTER OPERATION (GV-PT2U) 64
Auto capture ...................................................................... 64
ADVANCED OPERATIONS 66
Changing ID number ............................................................. 66
Connecting other device during operation..................................... 66
Changing the name of the device............................................... 67
Changing the device to use while
connecting over two same type devices .................................... 67
Adjusting the gap between the stored edit-start point
in the computer and the dubbed one in the recording deck............... 68
Counter reset ..................................................................... 69
When using the Video Capture Software ..................................... 69
TROUBLESHOOTING 70
MAJOR SPECIFICATIONS 72
INDEX 73
Make sure the GV-DS2U (optional) includes the following accessories:
3.5mm diameter 4-pole cable (x 2)
PC Connection Cable
(for PC/AT compatible computers)
CD-ROM including two
software programs:
JLIP Video Capture and JLIP
Video Producer software
JLIP Video Capture
Docking Station
GV-DS2U
10 EN
MAJOR FEATURES
Advanced Applications
Create title indexes for your video
collection
Title index images can be captured from your
favorite recordings in intervals of 30 minutes,
1 hour, 1.5 hours, etc. using the Interval
Capture mode. Print the captured index
images on your PC printer using the
computer’s Print Screen facility, then attach
them to your cassettes.
Video journal and postcards
Create your own original postcards, party
invitation cards and the like or keep a video
journal.
Business presentations
Images captured from video can be incorpo-
rated into business documents to spice up
your presentations.
Internet homepage
Images captured from video can be incorpo-
rated in your Internet homepage using image
editing software.
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Estación de acoplamiento de JVC
JVC
JVC KS-K6013J Manual de usuario
JVC
JVC 0397MKV*UN*VP Manual de usuario
JVC
JVC KS-K6012J Manual de usuario
JVC
JVC XS-SR3 Manual de usuario
JVC
JVC HA-RF100S Manual de usuario
JVC
JVC NX-PN10 Manual de usuario
JVC
JVC NX-PN7 Manual de usuario
JVC
JVC 0397MKV*UN*SN Manual de usuario
JVC
JVC GV-DS1DU Manual de usuario
JVC
JVC 0809DUMMDWJMM Manual de usuario
