JVC KD-G420 Manual de usuario
ENGLISH
ESPAÑOL
FRANÇAIS
CD RECEIVER KD-AR470/KD-G420
RECEPTOR CON CD KD-AR470/KD-G420
RECEPTEUR CD KD-AR470/KD-G420
For canceling the display demonstration, see page 7.
Para cancelar la demostración en pantalla, consulte la página 7.
Pour annuler la démonstration des affichages, référez-vous à la page 7.
For installation and connections, refer to the separate manual.
Para la instalación y las cone iones, refiérase al manual separado.
Pour l’installation et les raccordements, se référer au manuel séparé.
INSTRUCTIONS
MANUAL DE INSTRUCCIONES
MANUEL D’INSTRUCTIONS
For customer Use:
Enter below the Model
No. and Serial No. which
are located on the top or
bottom of the cabinet.
Retain this information
for future reference.
Model No.
Serial No.
GET0336-001A
[J]
2
ENGLISH
How to use the M MODE button
If you press M MODE, the unit goes into
functions mode, then the number buttons and
5/∞ buttons work as different function buttons.
Ex.: hen number button 2 works as
MO (monaural) button.
To use these buttons for their original
functions again after pressing M MODE, wait
for 5 seconds without pressing any of these
buttons until the functions mode is cleared or
press M MODE again.
Thank you for purchasing a JVC product.
Please read all instructions carefully before operation, to ensure your complete understanding and to
obtain the best possible performance from the unit.
INFORMATION (For U.S.A.)
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
– Consult the dealer or an experienced radio/TV technician for help.
IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave
all servicing to qualified service personnel.
3. CAUTION: Visible and invisible laser radiation when open and interlock failed or defeated.
Avoid direct exposure to beam.
How to reset your un t
Your preset adjustments will also be erased.
How to forc bly eject a d sc
“PLEASE” and “EJECT” appear alternately on
the display.
• If this does not work, reset your unit.
• Be careful not to drop the disc when it ejects.
Time countdown indicator
ENGLISH
3
How to read this manual
• Button operations are mainly explained with
the illustrations in the table below.
• Some related tips and notes are explained in
“More about this unit” (see pages 20 – 22 .
Press briefly.
Press repeatedly.
Press either
one.
Press and hold until your
desired response begins.
Press and hold both
buttons at the same time.
The following marks are used to indicate...
: Built-in CD player operations.
: External CD changer operations.
:
Indicator displayed for the
corresponding operation.
How to detach/attach the control
panel
CONTENTS
Control panel
—
KD-AR470 and KD-G420
4
Remote controller —
RM-RK50
5
Getting started 6
Basic operations .................................................... 6
Radio operations 7
Disc operations 8
Playing a disc in the unit ...................................... 8
Playing discs in the CD changer ............................ 9
Sound adjustments 11
General settings — PSM 12
Title assignment 15
External component operations
16
Satellite radio operations 17
More about this unit 20
Maintenance 22
Troubleshooting 23
Specifications 25
Warning:
If you need to operate the unit while driving,
be sure to look ahead carefully or you may be
involved in a traffic accident.
For safety
• Do not raise the volume level too much, as
this will block outside sounds, making driving
dangerous.
• Stop the car before performing any
complicated operations.
Temperature inside the car
If you have parked the car for a long time in hot
or cold weather, wait until the temperature in
the car becomes normal before operating the
unit.
Detaching...
Attaching...
4
ENGLISH
Control panel — KD-G612/KD-G611/KD-G511
1 5 (up) / ∞ (down) buttons
2 E EQ (equalizer) button
3 D DISP (display) button
4 S SEL (select) button
5 • Control dial
• (standby/on attenuator) button
6 Display window
7 Remote sensor
• DO NO expose the remote sensor to
strong light (direct sunlight or artificial
lighting).
8 0 (eject) button
9 4/¢ buttons
p (control panel release) button
q SOURCE button
w BAND button
e Number buttons
r MO (monaural) button
t SSM (Strong-station Sequential Memory)
button
y RPT (repeat) button
u RND (random) button
i M MODE button
o AUX (auxiliary) input jack
D splay w ndow
; Main display
a Disc information indicators—TAG (ID3
Tag), (folder), (track/file)
s EQ (equalizer) indicator
d Sound mode (C-EQ: custom equalizer)
indicators—ROCK, CLASSIC, POPS,
HIP HOP, JAZZ, USER
• also works as the time countdown
indicator and level meter during play (see
page 13).
f Tuner reception indicators—ST (stereo),
MO (monaural)
g Disc type indicators— MA, MP3
h Playback source indicators—
CH: Lights up only when CD-CH is selected
as the playback source.
DISC: Lights up for the built-in CD player.
j Playback mode / item indicators—
RND (random), (disc), (folder),
RPT (repeat)
k LOUD (loudness) indicator
l Source display / Volume level indicator
/ Tr (track) indicator
Parts dent f cat on
D splay w ndow
Control panel — KD-AR470 and KD-G420
ENGLISH
5
Caut on:
Ma n elements and features
1 (standby/on/attenuator) button
• Turns the power on if pressed briefly or
attenuates the sound when power is on.
• Turns the power off if pressed and held.
2 5 U (up) / D (down) ∞ buttons
• Changes the FM/AM bands with 5 U
only.
• Changes the preset stations with D ∞
only.
• Changes the folder of the MP3/ MA
discs.
• hile playing an MP3 disc on an
MP3-compatible CD changer:
– Changes the disc if pressed briefly.
– Changes the folder if pressed and held.
• hile listening to the satellite (SIRIUS or
XM) radio:
– Changes the categories.
Re ote controller — RM-RK50
RM-RK50 is supplied for KD-AR470.
KD-G420 can be remotely controlled as
instructed here (with an optionally purchased
remote controller). e recommend you to use
RM-RK50 or RM-RK60 with your unit.
Install ng the l th um co n battery
(CR2025)
Aim the remote controller directly at the
remote sensor on the unit. Make sure there is
no obstacle in between.
Warn ng:
• Do not install any battery other than
CR2025 or its equivalent; otherwise, it may
explode.
• Store the battery in a place where children
cannot reach to avoid risk of accident.
• To prevent the battery from over-heating,
cracking, or starting a fire:
– Do not recharge, short, disassemble,
heat the battery, or dispose of it in a fire.
– Do not leave the battery with other
metallic materials.
– Do not poke the battery with tweezers or
similar tools.
– rap the battery with tape and insulate
when throwing away or saving it.
o be continued...
6
ENGLISH
! • For FM/AM tuner
• For SIRIUS Satellite radio
• For XM Satellite radio
⁄ Adjust the volume.
@ Adjust the sound as you want. (See
pa es 11 and 12.)
Caution on volume setting:
Discs produce very little noise compared
with other sources. Lower the volume
before playing a disc to avoid damaging
the speakers by the sudden increase of the
output level.
To drop the volume
in a moment (ATT)
To restore the sound,
press it again.
To turn off the
power
3 VOL – VOL + buttons
• Adjusts the volume level.
4 SOUND button
• Selects the sound mode (C-EQ: custom
equalizer).
5 SOURCE button
• Selects the source.
6 2 R (reverse) F (forward) 3 buttons
• Searches for stations if pressed briefly.
• Fast-forwards or reverses the track if
pressed and held.
• Changes the tracks of the disc if pressed
briefly.
• While listening to the satellite radio:
– Changes the channels if pressed briefly.
– Changes the channels rapidly if pressed
and held.
Getting started
Basic operations
~ Turn on the power.
Ÿ
• Select “CD-CH” when using an Apple
iPod® or a JVC D. player (see page 16).
iPod is a trademark of Apple
Computer, Inc., registered in the U.S.
and other countries.
* You cannot select these sources if they
are not ready or not connected.
Volume level indicator
Volume level appears.
7
ENGLISH
Lights up when receiving an FM stereo
broadcast with sufficient signal strength.
Selected band appears.
Basic settings
• See also “General settings — PSM” on pages
12 – 14.
1
2
1 Cancelin the display
demonstrations
Select “DEMO,” then “DEMO OFF.”
2 Settin the clock
Select “CLOCK H” (hour), then adjust
the hour.
Select “CLOCK M” (minute), then
adjust the minute.
3 Finish the procedure.
To check the current clock
time when the power is
turned off
Radio operations
~
Ÿ
! Start searchin for a station.
When a station is received, searching
stops.
To stop searchin , press the same button
again.
To tune in to a station manually
In step ! above...
1
2 Select the desired station frequencies.
When an F stereo broadcast is hard to
receive
Reception improves, but stereo effect will be
lost.
To restore the stereo effect, repeat the same
procedure. “MONO OFF” appears and the MO
indicator goes off.
Lights up when monaural mode is activated.
8
ENGLISH
Listening to a preset station
1
2 Select the preset station (1 – 6) you
want.
or
To check the other information while
listening to an F or A station
* If no title is assigned to a station, “NO
NAME” appears. To assign a title to a
station, see page 1 .
Disc operations
Playing a disc in the unit
All tracks will be played repeatedly until you
change the source or eject the disc.
To stop play and eject the disc
Storing stations in memory
You can preset six stations for each band.
F station automatic presetting —
SS (Strong-station Sequential
emory)
1 Select the FM band (FM1 – FM3) you
want to store into.
2
3
“SSM” flashes, then disappears when
automatic presetting is over.
Local FM stations with the strongest signals are
searched and stored automatically in the FM
band.
anual presetting
Ex.: Storing FM station of 92.5 MHz into preset
number 4 of the FM1 band.
1
2
3
Clock = Station name* = Frequency =
(back to the beginning)
Preset number flashes for a while.
9
ENGLISH
Playing discs in the CD changer
All discs in the magazine will be played
repeatedly until you change the source.
• Ejecting the magazine will also stop playing.
~
* If you have changed “EXT IN” setting
to “EXT IN” (see page 14), you cannot
select the C changer.
See page 16 when using an iPod or JVC
. player.
Ÿ Select a disc.
For disc number from 01 – 0 :
For disc number from 07 – 12:
About MP3 and WMA discs
MP3 and WMA “tracks” (words “file” and
“track” are used interchangeably) are recorded
in “folders.”
About the CD changer
It is recommended to use a JVC MP3-
compatible CD changer with your unit.
• You can also connect other CH-X series CD
changers (except CH-X99 and CH-X100).
These units are not compatible with MP3
discs.
• You cannot play any WMA disc in the CD
changer.
• You cannot use the KD-MK series CD
changers with this unit.
• Disc text information recorded in the CD
Text can be displayed when a JVC CD Text
compatible CD changer is connected.
• For connection, see Installation/Connection
Manual (separate volume).
To fast-forward or reverse the track
To go to the next or revious tracks
To go to the next or revious folders (only for
MP3 or WMA discs)
For MP3 discs:
For WMA discs:
To locate a articular track (for CD) or folder
(for MP3 or WMA discs) directly
To select a number from 01 – 0 :
To select a number from 07 – 12:
• To use folder search on MP3/WMA discs, it is
required that folders are assigned with 2-digit
numbers at the beginning of their folder
names—01, 02, 03, and so on.
• To select a particular track in a folder (for
MP3 or WMA disc):
10
ENGLISH
Other main functions
Ski ing a track quickly during lay
Only ossible on JVC
MP3-com atible CD changer
• For MP3 or WMA disc, you can skip a track
within the same folder.
Ex.: To select track 32 while playing a track
whose number is a single digit (1 to 9)
1
2
Each time you press the button, you can
skip 10 tracks.
• After the last track, the first track will be
selected and vice versa.
3
Prohibiting disc ejection
You can lock a disc in the loading slot.
To cancel the prohibition, repeat the same
procedure.
Changing the dis lay information
While laying an audio CD or a CD Text
While laying an MP3 or a WMA*2 disc
• When “TAG DISP” is set to “TAG ON”
(see pa e 14)
• When “TAG DISP” is set to “TAG OFF”
: Clock with the current track number
: Elapsed playin time with the current
track number
*1 If the current disc is an audio C ,
“NO NAME” appears.
*2 Only for the built-in C player.
*3 If an MP3/WMA file does not have I 3 tags,
folder name and file name appear. In this
case, the TAG indicator will not light up.
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Receptor de coche de JVC
JVC
JVC KD-T401 Manual de usuario
JVC
JVC KD-S675 Manual de usuario
JVC
JVC KD-S845 Guía del administrador
JVC
JVC KS-FX470 Manual de usuario
JVC
JVC Car Cassette Deck KS-F500 Manual de usuario
JVC
JVC KD-SX841R Manual de usuario
JVC
JVC KD-A305J Manual de usuario
JVC
JVC KD-R80BT Guía
JVC
JVC KD-G311 Manual de usuario
JVC
JVC KS-LH4R Manual de usuario
