Jura IMPRESSA C9 Manual de usuario

IMPRESSA C9 – Quick Reference Guide

The ‘IMPRESSA Manual’ together with these short instruc-

tions ‘IMPRESSA C9 – Quick Reference Guide’ has been

awarded the seal of approval by the independent German

Technical Inspection Agency, TÜV SÜD, due to its easy-to-

understand style, its thoroughness and coverage of safety

aspects.

IMPRESSA C9 – Quick Reference Guide

These short instructions do not replace the ‘IMPRESSA C9 Manual’.

Make sure you read and observe the safety information and warn-

ings first in order to avoid hazards.

Precondition: Your IMPRESSA is switched on at the power switch and

the indicator light is illuminated (standby).

Q T Press the On/Off button to switch the IMPRESSA on.

HEATING is displayed.

PRESS RINSE, the maintenance button clights up.

Place a receptacle under the coffee spout.

c T Press the maintenance button.

RINSING, the machine rinses.

Preparation stops automatically. READY appears on the

display.

Your IMPRESSA no longer has to be descaled if you are using CLARIS

plus filter cartridges.

Perform the ’Insert filter’ operation without interruptions. This

will ensure that your IMPRESSA always produces its best.

Precondition: READY is displayed.

Open the cover of the Rotary Switch.

k T Keep the Rotary Switch pressed until RINSE appears on

the display.

g T Turn the Rotary Switch until FILTER - is displayed.

k T Press the Rotary Switch to enter the programme item.

NO -

g T Turn the Rotary Switch until YES w is displayed.

k T Press the Rotary Switch to confirm the setting.

OK appears briefly on the display to confirm the setting.

INSERT, the maintenance button clights up.

Close the cover of the Rotary Switch.

Remove the CLARIS plus filter cartridge from the Welcome

Pack.

Remove the water tank and empty it.

Switching onSwitching on

Using and activating

filter

Using and activating

filter

IMPRESSA C9 – Quick Reference Guide

Lift the cartridge holder and insert the filter cartridge into

the water tank, applying slight pressure.

Close the cartridge holder. It will click into place audibly.

Fill the water tank with fresh, cold water and reinsert.

Place a receptacle (at least 500 ml) under the frother.

c T Press the maintenance button.

FILTER RINSING. Water will flow out of the frother.

You can interrupt rinsing of the filter at any time by pressing

any button.

The water may be slightly discoloured. This is not harmful to

health and does not affect the taste.

Filter rinsing stops automatically after approx. 500 ml.

HEATING appears on the display, then READY is dis-

played. The filter is now activated.

After 50 litres of water have flowed through, or after two

months, the filter will cease to work. Your IMPRESSA will auto-

matically prompt you to change the filter.

If the CLARIS plus filter cartridge is not activated, you will not

be prompted to change the filter.

To change the CLARIS plus filter cartridge when prompted to do so

by your IMPRESSA, proceed as follows:

Precondition: READY / FILTER is displayed and the mainte-

nance button clights up.

c T Press the maintenance button.

CHANGE

Remove the water tank and empty it.

Open up the cartridge holder and remove the old CLARIS

plus filter cartridge.

Filter changeFilter change

IMPRESSA C9 – Quick Reference Guide

Insert a new CLARIS plus filter cartridge into the water tank,

pressing it slightly.

Close the cartridge holder. It will click into place audibly.

Fill the water tank with fresh, cold water and reinsert.

Place a receptacle (at least 500 ml) under the frother.

If you are using the Professional Cappuccino Frother, set the

selection lever of the frother to the steam position n.

c T Press the maintenance button.

FILTER RINSING – Water will flow out of the frother.

You can interrupt filter rinsing at any time. To do this, press

any button.

The water may be slightly discoloured. This is not harmful to

health and does not affect the taste.

Filter rinsing stops automatically after approx. 500 ml. The

IMPRESSA heats up and is once again ready to use.

After 200 coffee preparations or 80 switch-on rinses, the IMPRESSA

will prompt you to clean it.

If the wrong cleaning agent is used, the machine could be damaged

and/or traces of detergent could be left behind in the water.

Use only original JURA care products.

The cleaning programme only lasts about 20 minutes.

Do not interrupt the cleaning programme. The quality of

cleaning will be impaired if you do so.

JURA cleaning tablets are available from stockists.

Precondition: READY / CLEAN is displayed and the maintenance

button clights up.

c T Press the maintenance button.

Clean machineClean machine

CAUTIONCAUTION

IMPRESSA C9 – Quick Reference Guide

EMPTY TRAY

Empty the drip tray and coffee grounds container and put

them back into the machine.

PRESS RINSE, the maintenance button clights up.

Place a receptacle under the coffee spout and the frother.

c T Press the maintenance button.

CLEANING, water flows from both coffee spouts.

The process is interrupted, ADD TABLET.

Open the cover of the filler funnel for pre-ground coffee.

Insert a JURA cleaning tablet into the filler funnel.

Close the cover of the filler funnel.

c T Press the maintenance button.

CLEANING, water flows from both coffee spouts several

times.

The process is interrupted – EMPTY TRAY.

Empty the drip tray and coffee grounds container and put

them back into the machine.

The cleaning operation is now complete. The IMPRESSA is

ready for use again.

IMPRESSA C9 – Quick Reference Guide

The IMPRESSA builds up deposits of limescale over time and auto-

matically prompts you to descale it when necessary. The degree of

calcification depends on the degree of hardness of your water.

If the descaling agent comes into contact with the skin or eyes, this

can cause irritation.

Avoid contact with the skin or eyes.

Rinse the descaling agent off with clean water. Should you get

any descaling agent in your eye, see a doctor.

If the wrong descaling agent is used, the machine could be dam-

aged and/or traces of detergent could be left behind in the water.

Use only original JURA care products.

If the descaling operation is interrupted, there may be damage to

the machine.

Allow the descaling program to run to the end.

If the descaling agent comes into contact with sensitive surfaces,

damage cannot be ruled out.

Clean up any splashes immediately.

The descaling programme lasts approx. 45 minutes.

JURA descaling tablets are available from stockists.

If you use a CLARIS plus filter cartridge and this is activated,

you will not be prompted to change the filter.

Precondition: READY / DE-SCALE is displayed and the mainte-

nance button clights up.

c T Press the maintenance button.

EMPTY TRAY

Empty the drip tray and coffee grounds container and put

them back into the machine.

AGENT IN TANK

Remove the water tank and empty it.

Descale machineDescale machine

CAUTIONCAUTION

IMPRESSA C9 – Quick Reference Guide

Completely dissolve the contents of one blister (3 JURA des-

caling tablets) in a container that holds 500 ml of water. This

may take several minutes.

Pour the solution into the empty water tank and insert it in

the machine.

AGENT IN TANK, the maintenance button clights up.

Remove the frother.

Place a receptacle (at least 500 ml) under the Connector Sys-

tem©.

c T Press the maintenance button.

DE-SCALING

This causes water to flow out of the Connector System©sev-

eral times. The maintenance button blinks during the des-

caling operation.

The operation stops automatically, EMPTY TRAY.

Empty the receptacle under the Connector System©.

Empty the drip tray and coffee grounds container and put

them back into the machine.

FILL WATER TANK

Remove the water tank and rinse it thoroughly.

Fill the water tank with fresh, cold mains water and rein-

sert.

PRESS RINSE, the maintenance button clights up.

Replace the frother.

Place a receptacle under the frother.

c T Press the maintenance button.

DE-SCALING, water flows out of the frother.

The operation stops automatically, EMPTY TRAY.

Empty the drip tray and coffee grounds container and put

them back into the machine.

The descaling operation is now complete. Your IMPRESSA

heats up and is once again ready to use.

If the descaling operation stops unexpectedly, rinse the water

tank thoroughly.

IMPRESSA C9 – Quick Reference Guide

To ensure that the Easy Cappuccino Frother works perfectly, you

should rinse it with water whenever you have prepared some milk.

Your IMPRESSA will prompt you to rinse the Easy Cappuccino Frother

10 minutes after you have prepared milk.

Precondition: CAPPUCCINO RINSE is displayed and the main-

tenance button clights up.

Place a receptacle under the Easy Cappuccino Frother.

c T Press the maintenance button.

CAPPUCCINO RINSING, the frother is rinsed.

Preparation stops automatically. READY appears on the

display.

To ensure that the Easy Cappuccino Frother works perfectly, you

should clean it daily when you have been preparing milk.

If the wrong cleaning agent is used, the machine could be damaged

and/or traces of detergent could be left behind in the water.

Use only original JURA care products.

The JURA Auto Cappuccino Cleaner is available from

stockists.

The IMPRESSA will not prompt you to clean the frother.

Precondition: READY is displayed.

Remove the milk pipe from the milk carton/bottle or the

milk container.

Open the cover of the Rotary Switch.

k T Keep the Rotary Switch pressed until RINSE appears.

k T Press the Rotary Switch to enter the programme item.

C CLEANING

k T Press the Rotary Switch.

CAPPUCCINO CLEANER

Pour 250 ml of fresh water into a container and add one cap-

ful (max. 15 ml) of Auto Cappuccino Cleaner.

Rinsing the Easy

Cappuccino Frother

Rinsing the Easy

Cappuccino Frother

Cleaning the Easy

Cappuccino Frother

Cleaning the Easy

Cappuccino Frother

CAUTIONCAUTION

IMPRESSA C9 – Quick Reference Guide

Immerse the milk pipe in the receptacle.

Place another receptacle under the frother.

c T Press the maintenance button.

CLEANING, the frother and pipe are cleaned. The opera-

tion stops automatically.

WATER FOR CAPPUCCINO

Rinse the receptacle thoroughly, fill it with approx. 250 ml

of fresh water and immerse the milk pipe in the water.

Empty the other receptacle and place it under the frother

once more.

c T Press the maintenance button.

CLEANING, the frother and pipe are rinsed with fresh

water. The operation stops automatically.

READY appears on the display.

Close the cover of the Rotary Switch.

Carefully remove the frother from the Connector System©

by twisting slightly.

Dismantle the frother completely.

Rinse all the frother parts thoroughly under running water.

Reassemble the frother.

Ensure that the individual parts are correctly and firmly

attached to one another to ensure optimum function of the

frother.

Firmly attach the frother to the Connector System©.

Disassembling and

rinsing the Easy

Cappuccino Frother

Disassembling and

rinsing the Easy

Cappuccino Frother

IMPRESSA C9 – Quick Reference Guide

To ensure that the Professional Cappuccino Frother works perfectly,

you should rinse it with water whenever you have prepared some

milk.

Your IMPRESSA will prompt you to rinse the Professional Cappuc-

cino Frother 10 minutes after you have prepared milk.

Precondition: CAPPUCCINO RINSE is displayed and the main-

tenance button clights up.

Place a receptacle under the Professional Cappuccino

Frother.

c T Press the maintenance button.

CAPPUCCINO RINSING, the frother is rinsed.

Preparation stops automatically. READY appears on the

display.

To ensure that the Professional Cappuccino Frother works perfectly,

you should clean it daily when you have been preparing milk.

If the wrong cleaning agent is used, the machine could be damaged

and/or traces of detergent could be left behind in the water.

Use only original JURA care products.

The JURA Auto Cappuccino Cleaner is available from

stockists.

The IMPRESSA will not prompt you to clean the frother.

Precondition: READY is displayed.

Open the cover of the Rotary Switch.

k T Keep the Rotary Switch pressed until RINSE appears.

k T Press the Rotary Switch to enter the programme item.

C CLEANING

k T Press the Rotary Switch.

CAPPUCCINO CLEANER

Remove the milk pipe from the milk carton/bottle or the

milk container.

Pour 250 ml of fresh water into a container and add one cap-

ful (max. 15 ml) of Auto Cappuccino Cleaner.

Rinsing

the Professional

Cappuccino Frother

Rinsing

the Professional

Cappuccino Frother

Cleaning

the Professional

Cappuccino Frother

Cleaning

the Professional

Cappuccino Frother

CAUTIONCAUTION

Otros manuales para IMPRESSA C9

Tabla de contenidos

Otros manuales de Cafetera de Jura

Jura

Jura ENA Micro 9 One Touch Manual de usuario

Jura

Jura Z6 Manual de usuario

Jura

Jura WE6 Professional Manual

Jura

Jura GIGA 10 Manual de usuario

Jura

Jura IMPRESSA Z7 Manual de usuario

Jura

Jura GIGA G2 Manual de usuario

Jura

Jura D6 Manual de usuario

Jura

Jura IMPRESSA S70 Manual de usuario

Jura

Jura IMPRESSA XJ9 OT TFT Professional Manual

Jura

Jura X6 Manual de usuario

Jura

Jura GIGA X8 Professional Manual de usuario

Jura

Jura IMPRESSA X9 Win Manual de usuario

Jura

Jura IMPRESSA XJ9 Professional Manual de usuario

Jura

Jura ENA Micro 5 Manual de usuario

Jura

Jura ENA Micro 5 Manual de usuario

Jura

Jura IMPRESSA C9 Manual de usuario

Jura

Jura GIGA X7 Professionel Manual de usuario

Jura

Jura IMPRESSA Z5 Manual de usuario

Jura

Jura 729 Manual de usuario

Jura

Jura The IMPRESSA Z5 - Generation II Manual de usuario

Jura

Jura 765 Manual de usuario

Jura

Jura IMPRESSA J9.2 One Touch Manual de usuario

Jura

Jura D4 Manual de usuario

Jura

Jura IMPRESSA Z7 Manual de usuario

Manuales populares de Cafetera de otras marcas

Taurus

Taurus Livorno 6 Manual de usuario

Delta-q

Delta-q QUICK Manual de usuario

Bunn

Bunn LCA-1 Guía de solución de problemas

Black & Decker

Black & Decker BLACK DECKER HOME DE790 Instrucciones de instalación

Saeco

Saeco Vienna Plus Sup 018M Manual de usuario

DeLonghi

DeLonghi DC300 Manual de usuario

INCAPTO

INCAPTO BXCO1470E Manual de usuario

Bosch

Bosch TASSIMO finesse TAS16B Series Manual de usuario

Exido

Exido 245-072 Manual de usuario

Animo

Animo OptiVend Choco Manual de usuario

Siemens

Siemens TQ505DF Series Manual de usuario

DeLonghi

DeLonghi ECI341 Manual de usuario

Krups

Krups KT406511 Manual de usuario

Cimbali

Cimbali M32 Classic Manual de usuario

Philips

Philips HL3844N Manual de usuario

Bosch

Bosch TES 515 SERIES Manual de usuario

Tekmatix

Tekmatix TMFM - 65 Manual de usuario

Scarlett

Scarlett SC-CM33005 Manual de usuario