Jura E8 Manual de usuario

E8/E80 – Quick Reference Guide

These short instructions do not replace the ‘E8/E80 Instructions for

Use’. Make sure you read and observe the safety information and

warnings first in order to avoid hazards.

You can start coffee system rinsing manually at any time.

TPlace a receptacle under the coffee spout.

TPress the ‘Pc’ button.

TPress the ‘>’ button.

TPress the ‘Rinse the coffee system’ button to start the rinse

operation.

‘Machine is rinsing’, water flows out of the coffee spout. The

operation stops automatically.

EThis chapter applies to the professional fine foam frother and

the fine foam frother.

After each milk preparation, the JURA prompts you to perform a milk

system rinse.

EIn programming mode, you can set whether the milk system

rinsing is to be prompted 10 minutes after preparation or initi-

ated automatically (see Chapter 4 ‘Permanent settings in pro-

gramming mode – Milk system rinsing’).

Precondition:‘Rinse the milk system’ is displayed.

TPlace a receptacle under the fine foam frother.

TPress the ‘Pc’ button.

TPress the ‘>’ button.

TPress the ‘Rinse the milk system’ button to start the rinse

operation.

‘Milk system is being rinsed’ appears and the fine foam

frother is rinsed. The operation stops automatically.

Rinsing the machine

éè

Rinsing the fine foam

frother

éè

E8/E80 – Quick Reference Guide

EThis chapter applies to the professional fine foam frother and

the fine foam frother.

To ensure that the fine foam frother always works properly, you

must clean it daily when you have been preparing milk.

If the wrong cleaning agent is used, the machine could be damaged

and/or traces could be left behind in the water.

T Use only original JURA maintenance products.

EJURA milk system cleaner is available from specialised dealers.

ETo clean the milk system, use the container supplied.

TPress the ‘Pc’ button.

TPress the ‘Clean the milk system’ button.

‘Clean the milk system’

TPress the ‘Start’ button.

TPress the ‘Next’ button.

‘Clean the milk system’ / ‘Milk system cleaner’

TRemove the milk pipe from the milk container or carton.

TAdd milk system cleaner to the front part of the container

up to the bottom mark (indicated by 6).

TThen fill with water up to the upper mark.

TPlace the container under the fine foam frother.

TIf you are using the professional fine foam frother, set the

setting wheel to the Milk Foam position é.

TConnect the milk pipe to the container.

ETo connect the milk pipe to the container correctly, the pipe

must be fitted with a connector.

TPress the ‘Next’ button.

‘Milk system is being cleaned’ appears and the fine foam

frother and the milk pipe are cleaned.

Cleaning the fine foam

frother

CAUTION

éè

E8/E80 – Quick Reference Guide

TDuring the first brief interruption, set the setting wheel of

the professional fine foam frother to the Milk position è.

‘Clean the milk system’

TRinse the container thoroughly and fill the front part with

250ml of fresh water.

TPlace this under the fine foam frother and reconnect the

milk pipe to the container.

TPress the ‘Next’ button.

‘Milk system is being cleaned’ appears and the fine foam

frother and the milk pipe are rinsed with fresh water.

The start screen is displayed.

To make sure the professional fine foam frother works properly, and

in the interests of hygiene, it must be dismantled and rinsed daily if

you have been preparing milk. Your JURA will not prompt you to dis-

mantle and rinse the professional fine foam frother.

TRemove the milk pipe and rinse it thoroughly under running

water.

TCarefully remove the professional fine foam frother from the

Connector System©by twisting slightly.

TDismantle the professional fine foam frother into its individ-

ual parts.

TRinse all the parts under running water. If there are severely

dried-on milk residues, firstly immerse the individual parts

in a solution of 250ml cold water and 1 capful of JURA milk

system cleaner. Then rinse the parts thoroughly.

TRe-assemble the professional fine foam frother.

EEnsure that all individual parts are correctly and firmly

connected to ensure optimum operation of the professional

fine foam frother.

TFirmly attach the professional fine foam frother to the

Connector System©.

To make sure the fine foam frother works properly, and in the inter-

ests of hygiene, it must be dismantled and rinsed daily if you have

been preparing milk. Your JURA will not prompt you to dismantle

and rinse the frother.

TRemove the milk pipe and rinse it thoroughly under running

water.

éè

Dismantling and rinsing

the professional fine

foam frother

éè

Dismantling and rinsing

the fine foam frother

E8/E80 – Quick Reference Guide

TCarefully remove the fine foam frother from the Connector

System©by twisting slightly.

TDismantle the fine foam frother into its individual parts.

TRinse all the parts under running water. If there are severely

dried-on milk residues, firstly immerse the individual parts

in a solution of 250ml cold water and 1 capful of JURA milk

system cleaner. Then rinse the parts thoroughly.

TRe-assemble the fine foam frother.

EEnsure that all individual parts are correctly and firmly con-

nected to ensure optimum operation.

TFirmly attach the fine foam frother to the Connector Sys-

tem©.

Your JURA no longer has to be descaled if you are using the CLARIS

Smart filter cartridge. If you did not insert the filter cartridge the first

time you used the machine, you can do this now as follows.

Precondition:The start screen is displayed.

TRemove and empty the water tank.

TFit the filter cartridge extension supplied on top of a CLARIS

Smart filter cartridge.

TInsert the filter cartridge with its extension into the water

tank.

TTurn the filter cartridge clockwise until it audibly clicks into

place.

TFill the water tank with fresh, cold water and reinsert the

tank.

EThe machine automatically detects that you have just inserted

the filter cartridge.

‘Saved’ appears briefly on the display.

‘Filter is beingrinsed’, the water flows directly into the drip

tray.

Rinsing of the filter stops automatically after approximately

300ml. The start screen is displayed.

EIf the filter is active, this is indicated by a blue filter symbol at

the bottom of the display.

Inserting the filter

E8/E80 – Quick Reference Guide

EOnce the filter cartridge stops working (depending on the

water hardness setting), the JURA will prompt you to change

the filter.

ECLARIS Smart filter cartridges are available from specialised

dealers.

Precondition:The start screen is displayed. The filter symbol at the

bottom of the display lights up red.

TRemove and empty the water tank.

TTurn the filter cartridge anticlockwise and remove it along

with the extension from the water tank.

TFit the filter cartridge extension on top of a new CLARIS

Smart filter cartridge.

TInsert the filter cartridge with its extension into the water

tank.

TTurn the filter cartridge clockwise until it audibly clicks into

place.

TFill the water tank with fresh, cold water and reinsert the

tank.

‘Saved’ appears briefly on the display. The machine has

automatically detected that you have just changed the filter

cartridge.

‘Filter is beingrinsed’, the water flows directly into the drip

tray.

Rinsing of the filter stops automatically after approximately

300ml. The start screen is displayed.

After 180preparations or 80switch-on rinses, the JURA will prompt

you to clean it.

If the wrong cleaning agent is used, the machine could be damaged

and/or traces could be left behind in the water.

T Use only original JURA maintenance products.

EThe cleaning programme lasts approximately 20 minutes.

EDo not interrupt the cleaning programme. The quality of

cleaning will be impaired if you do so.

EJURA cleaning tablets are available from specialised dealers.

Precondition:‘Clean machine’ is displayed.

TPress the ‘Pc’ button.

Changing the filter

Cleaning the machine

CAUTION

E8/E80 – Quick Reference Guide

TPress the ‘Start’ button.

TPress the ‘Next’ button.

‘Empty coffee grounds container’

TEmpty the drip tray and coffee grounds container and put

them back into the machine.

‘Clean’

TPlace a receptacle under the coffee spout.

TPress the ‘Next’ button.

‘Machine is being cleaned’, water flows out of the coffee

spout.

The operation is interrupted, ‘Add cleaning tablet’.

TOpen the cover of the filler funnel for ground coffee.

TInsert a JURA cleaning tablet into the filler funnel.

TClose the cover of the filler funnel.

TPress the ‘Next’ button.

‘Machine is being cleaned’, water flows out of the coffee

spout several times.

The operation stops automatically.

‘Empty coffee grounds container’

TEmpty the drip tray and coffee grounds container and put

them back into the machine.

Cleaning is now complete. The start screen is displayed.

The JURA builds up deposits of limescale over time and automati-

cally prompts you to descale it when necessary. The degree of calci-

fication depends on the hardness of your water.

EIf you are using a CLARIS Smart filter cartridge, you will not be

prompted to descale.

If the descaling agent comes into contact with the skin or eyes, this

can cause irritation.

T Avoid contact with the skin or eyes.

T Rinse off the descaling agent with clean water. Should you get

any descaling agent in your eye, see a doctor.

If the wrong descaling agent is used, the machine could be dam-

aged and/or traces could be left behind in the water.

T Use only original JURA maintenance products.

éè

Descaling the machine

JCAUTION

CAUTION

E8/E80 – Quick Reference Guide

If the descaling operation is interrupted, there may be damage to

the machine.

T Allow the descaling programme to run to the end.

If the descaling agent comes into contact with sensitive surfaces

(e.g. marble), damage cannot be ruled out.

T Clean up any splashes immediately.

EThe descaling programme lasts approximately 40minutes.

EJURA descaling tablets are available from specialised dealers.

Precondition:‘Decalcify machine’ is displayed.

TPress the ‘Pc’ button.

TPress the ‘Start’ button.

TPress the ‘Next’ button.

‘Empty drip tray’

TEmpty the drip tray and coffee grounds container and put

them back into the machine.

‘Agent in tank’

TRemove and empty the water tank.

TCompletely dissolve the contents of one blister (3JURA des-

caling tablets) in a receptacle holding 500ml of lukewarm

water. This may take several minutes.

TPour the solution into the empty water tank and insert it into

the machine.

TPlace a receptacle under the fine foam frother.

TPress the ‘Next’ button.

‘Machine is being descaled’ appears and water flows out of

the fine foam frother repeatedly.

The operation is interrupted, ‘Empty drip tray’.

TEmpty the drip tray and coffee grounds container and put

them back into the machine.

‘Fill water tank’

TRemove the water tank and rinse it thoroughly.

TFill the water tank with fresh, cold water and reinsert the

tank.

CAUTION

éè

E8/E80 – Quick Reference Guide

TPlace one receptacle under the coffee spout and another

under the fine foam frother.

TPress the ‘Next’ button.

‘Machine is being descaled’, the descaling operation is con-

tinued.

The operation is interrupted, ‘Empty drip tray’.

TEmpty the drip tray and coffee grounds container and put

them back into the machine.

Descaling is now complete. The start screen is displayed.

EIf the descaling operation stops unexpectedly, rinse the water

tank thoroughly.

Coffee beans may be covered with a slight oil film which remains on

the walls of the bean container. These traces may negatively affect

the coffee result. For this reason clean the bean container from time

to time.

Precondition:‘Fill bean container’ is displayed.

TSwitch the machine off with the On/Off button Q.

TRemove the aroma preservation cover.

TClean the bean container with a soft, dry cloth.

TFill the bean container with coffee beans and close the

aroma preservation cover.

Limescale deposits may form in the water tank. To ensure correct

function of the machine, descale the water tank from time to time.

TRemove the water tank.

TIf you use a CLARIS Smart filter cartridge, remove this.

TCompletely fill the water tank and dissolve 3 JURA descaling

tablets in it.

TLeave the water tank with the descaling solution for several

hours (e.g. overnight).

TEmpty the water tank and rinse it thoroughly.

TIf you use a CLARIS Smart filter cartridge, insert this again.

TFill the water tank with fresh, cold water and reinsert the

tank.

éè

Cleaning the bean

container

Descaling the water tank

E8_Kurz/en/201711

Otros manuales para E8

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cafetera de Jura

Jura

Jura Impressa F9 guide Manual de usuario

Jura

Jura IMPRESSA X7-S Manual de usuario

Jura

Jura GIGA X7 Professionel Manual de usuario

Jura

Jura IMPRESSA XS95 ONE TOUCH Manual de usuario

Jura

Jura IMPRESSA Z7 Manual de usuario

Jura

Jura IMPRESSA S9 One Touch Manual de instrucciones

Jura

Jura IMPRESSA C5 Manual de usuario

Jura

Jura GIGA X7 Professional Manual de usuario

Jura

Jura 760 Manual de usuario

Jura

Jura Giga X3 Professional Manual de usuario

Jura

Jura IMPRESSA XF50 Classic Manual de usuario

Jura

Jura IMPRESSA C9 Manual de usuario

Jura

Jura A1/A100 Manual de usuario

Jura

Jura X90/X95 Manual de usuario

Jura

Jura IMPRESSA XS95 Manual de usuario

Jura

Jura IMPRESSA A9 One Touch Manual de usuario

Jura

Jura 762 Manual de usuario

Jura

Jura E6 Manual de usuario

Jura

Jura IMPRESSA XJ5 Professional Manual de usuario

Jura

Jura IMPRESSA J9.3 One Touch TFT Manual de usuario

Jura

Jura IMPRESSA J9 One Touch Manual de usuario

Jura

Jura IMPRESSA C50 Manual de usuario

Jura

Jura Z6 Manual de usuario

Jura

Jura GIGA G2 Manual de usuario

Manuales populares de Cafetera de otras marcas

Taurus

Taurus Livorno 6 Manual de usuario

Delta-q

Delta-q QUICK Manual de usuario

Bunn

Bunn LCA-1 Guía de solución de problemas

Black & Decker

Black & Decker BLACK DECKER HOME DE790 Instrucciones de instalación

Saeco

Saeco Vienna Plus Sup 018M Manual de usuario

DeLonghi

DeLonghi DC300 Manual de usuario

INCAPTO

INCAPTO BXCO1470E Manual de usuario

Bosch

Bosch TASSIMO finesse TAS16B Series Manual de usuario

Exido

Exido 245-072 Manual de usuario

Animo

Animo OptiVend Choco Manual de usuario

Siemens

Siemens TQ505DF Series Manual de usuario

DeLonghi

DeLonghi ECI341 Manual de usuario

Krups

Krups KT406511 Manual de usuario

Cimbali

Cimbali M32 Classic Manual de usuario

Philips

Philips HL3844N Manual de usuario

Bosch

Bosch TES 515 SERIES Manual de usuario

Tekmatix

Tekmatix TMFM - 65 Manual de usuario

Scarlett

Scarlett SC-CM33005 Manual de usuario