Juniper EX Series Guía

Mounting an EX8208 Switch on a Rack or Cabinet Using a Mechanical Lift

Because of the switch's size and weight, we strongly recommend using a mechanical

lift to install the switch.

NOTE: For instructions on installing a switch without using a mechanical lift, see

Mounting an EX8208 Switch on a Rack or Cabinet Without Using a Mechanical Lift.

CAUTION: Do not install line cards in the chassis until after you mount the chassis

securely on a rack or cabinet.

CAUTION: Before front-mounting the switch on a rack or cabinet, have a qualified

technician verify that the rack or cabinet is strong enough to support the switch's

weight and is adequately supported at the installation site.

Before you install the switch:

■Prepare the site for installation as described in Site Preparation Checklist for an

EX8200 Switch.

■Ensure the site has adequate clearance for both airflow and hardware

maintenance as described in Clearance Requirements for Airflow and Hardware

Maintenance for an EX8208 Switch.

■Unpack the switch as described in Unpacking an EX8200 Switch.

■In a two-post rack, install the power cord tray at the desired position (see Installing

the Power Cord Tray in a Rack or Cabinet for an EX8200 Switch). The lip of the

power cord tray will support the front of the chassis when you install the switch

in the two-post rack.

■In a four-post rack, install the adjustable mounting brackets at the desired position

(see Installing Adjustable Mounting Brackets in a Rack or Cabinet for an EX8200

Switch). Optionally, you can also install the power cord tray and use it to manage

the power supply cords.

■Review chassis lifting guidelines described in Chassis Lifting Guidelines for EX8200

Switches.

Ensure that you have the following parts and tools available to install the switch:

■A mechanical lift

■24 mounting screws appropriate for your rack

■A Phillips (+) screwdriver, number 2 or number 3, depending on the size of

your rack mounting screws

Mounting an EX8208 Switch on a Rack or Cabinet Using a Mechanical Lift ■1

CAUTION: If you are installing more than one switch in a rack or cabinet, install the

first switch at the bottom of the rack.

To install the switch using a mechanical lift (see Figure 1):

1. Ensure that the rack or cabinet is placed in its permanent location and is secured

to the building. Ensure that the installation site allows adequate clearance for

both airflow and maintenance. For details, see Clearance Requirements for

Airflow and Hardware Maintenance for an EX8208 Switch.

2. Load the switch onto the lift, making sure it rests securely on the lift platform.

Figure 1: Installing the EX8208 Switch Chassis Using a Mechanical Lift

3. Using the lift, position the switch in front of the rack or cabinet, centering it in

front of the adjustable mounting brackets and/or power cord tray installed in the

rack.

4. Lift the chassis approximately 0.75 in. (1.9 cm) above the surface of the adjustable

mounting brackets/power cord tray. Position the chassis in the rack as close as

possible to resting on the support that the mounting brackets and/or power cord

tray provide.

2■Mounting an EX8208 Switch on a Rack or Cabinet Using a Mechanical Lift

5. In a four-post rack, carefully slide the switch onto the adjustable mounting

brackets until the front-mounting brackets (“ears”) attached to the chassis contact

the rack rails. The adjustable mounting brackets installed in the rack ensure that

the holes in the front-mounting brackets align with the holes in the rack rails.

In a two-post rack, carefully slide the switch into the rack ensuring that the front

bottom of the chassis rests on the lip of the power cord tray. The front-mounting

brackets (“ears”) prevent the chassis from tipping too far back.

6. Move the lift away from the rack.

7. In a four-post rack, slide the chassis so that the front-mounting bracket is flush

with the front of the rack.

In a two-post rack, push the bottom of the chassis so that the front-mounting

bracket is flush with the front of the rack.

8. Install a mounting screw into each of the open front-mounting holes aligned with

the rack, starting from the bottom.

9. Visually inspect the alignment of the switch. If the switch is installed properly in

the rack, all the mounting screws on one side of the rack are aligned with the

mounting screws on the opposite side and the switch is level.

10. After ensuring that the switch is aligned properly, tighten the screws.

Related Topics Powering On an EX8200 Switch■

■Connecting and Configuring an EX Series Switch (CLI Procedure)

■Connecting and Configuring an EX Series Switch (J-Web Procedure)

Published: 2009-07-15

Mounting an EX8208 Switch on a Rack or Cabinet Using a Mechanical Lift ■3

Otros manuales para EX Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cambiar de Juniper

Juniper

Juniper EX8200 Series Manual de instrucciones

Juniper

Juniper QFX5200-32C Manual de usuario

Juniper

Juniper EX9204 Manual de usuario

Juniper

Juniper EX2300 Series Manual de usuario

Juniper

Juniper EX2300-24P Manual de usuario

Juniper

Juniper EX8200 Series Manual de usuario

Juniper

Juniper EX8200 Series Guía de inicio rápido

Juniper

Juniper EX4550 Instrucciones de instalación

Juniper

Juniper NFX350 Instrucciones de instalación

Juniper

Juniper EX8208 Manual de usuario

Juniper

Juniper EX2200 Series Manual de usuario

Juniper

Juniper EX 4200 24F Manual de usuario

Juniper

Juniper EX2200 Series Instrucciones de instalación

Juniper

Juniper EX8200 Series Manual de usuario

Juniper

Juniper EX3200 Series Guía de inicio rápido

Juniper

Juniper EX8208 Manual de usuario

Juniper

Juniper EX2200 Series Manual de usuario

Juniper

Juniper EX 3200 Manual de usuario

Juniper

Juniper QFX5120 Series Manual de usuario

Juniper

Juniper EX2500 Instrucciones de instalación

Juniper

Juniper QFX5100-48T Manual de usuario

Juniper

Juniper EX4500 Series Instrucciones de instalación

Juniper

Juniper EX3300 Manual de usuario

Juniper

Juniper EX 3200 Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario