Johnson 40-6690 Manual de usuario

Pipe Laser

Model No. 40-6690

Instruction Manual

Congratulations on your choice of this Pipe Laser. We suggest you read this instruction

manual thoroughly before using the pipe laser. Save this instruction manual for future use.

The 40-6690 pipe laser is an easy-to-use laser that provides underground contractors line,

elevation, and grade control for installing storm, sanitary, or other gravity-flow drainage pipe.

This system can also be used for tunneling, boring, pipe alignment, or any other application

requiring line, elevation, and grade control.

The pipe laser emits a highly visible red beam of laser light in a direction at a predetermined

(grade) for the alignment of gravity-flow pipe. The laser light is intercepted at the opposite end

of the pipe by the pipe laser target. To align the pipe, position it so that the pipe laser’s beam is

centered in the target.

This is a Class a laser tool and is manufactured to comply with CFR 21, parts 1040.10 and

1040.11 as well as international safety rule EC 285.

Table of Contents

1. Kit Contents

2. Features and Functions

3. Safety nstructions

4. Location/Content

of Warning Labels

5. Location of Parts/Components

6. Operating nstructions

7. Using the Product

8. Self-Check & Fine Calibration

9. Technical Specifications

10. Care and Handling

11. Product Warranty

12. Warranty Registration

13. Accessories

1. Kit Contents

Description for Model 40-6690 Qty.

Pipe Laser 1

Rechargeable Battery pack 1

Alkaline Battery Pack (batteries not included) 1

6.4V Charger Adapter 1

12V Car Charger 1

Targets 2

Leg Sets 5

3rd Leg 1

Remote Control with 9V Battery 1

nstruction Manual with Warranty Card 1

Hard-Shell Carrying Case 1

2. Features and Functions

• Electric self-leveling

• Out of level indicator, laser beam will blink and LCD symbol will indicate

out of level position

• Large grade range

• Quickly reset the line to the center position

• Stand by mode to conserve battery

• Operates with remote control

• Various leg sets and targets for different size pipe

• Waterproof

3. Safety Instructions

Please read and understand all of the following instructions, prior to using this tool.

Failure to do so, may void the warranty.

DANGER!

Class a Laser Product

Max. Power Output: ≤5mW

Wavelength: 625-645nm

THIS TOOL EMITS LASER RADIATIO .

DO OT STARE I TO BEAM.

AVOID DIRECT EYE EXPOSURE.

ATTENTION IMPORTANT

•Read all instructions prior to operating this laser tool. Do not remove any labels from tool.

•Do not stare directly at the laser beam.

•Do not project the laser beam directly into the eyes of others.

•Do not set up laser tool at eye level or operate the tool near a reflective surface as

the laser beam could be projected into your eyes or into the eyes of others.

•Do not place the laser tool in a manner that may cause someone to unintentionally

look into the laser beam. Serious eye injury may result.

•Do not operate the tool in explosive environments, i.e. in the presence of gases or

flammable liquids.

•Keep the laser tool out of the reach of children and other untrained persons.

•Do not attempt to view the laser beam through optical tools such as telescopes as

serious eye injury may result.

•Always turn the laser tool off when not in use or left unattended for a period of time.

•Remove the batteries when storing the tool for an extended time (more than 3 months)

to avoid damage to the tool should the batteries deteriorate.

•Do not attempt to repair or disassemble the laser tool. f unqualified persons attempt

to repair this tool, warranty will be void.

•Use only original Johnson®parts and accessories purchased from your Johnson®

authorized dealer. Use of non-Johnson®parts and accessories will void warranty.

4. Location/Content of Warning Labels

5. Location of Part/Components

Line & xis pivot m rker & LED

B ck remote receiving window

LCD window

Keyp d

H ndle

Extern l power recept cle

B ttery p ck

B ck leg

1/4” Thre d Mount

Front leg

5/8 x 11 thre d

Gr de - Axis pivot

m rker

L ser Exit

Window

Front remote

receiving window

Option l Adjust ble Trivet St nd 40-6391

Elev ting lock knob

TILT lock knob Adjusting knobs

L ser mounting

Accessories Included

Sm ll nd l rge t rgets V rious leg sets

6. Operating Instructions

IMPORTA T: t is the responsibility of the user to verify the calibration of the

instrument before each use.

Battery installation

a) Put 4 “D” alkaline batteries into the battery pack

following the polarity direction indication. Put the

alkaline battery pack cover back, and install the

battery pack into the laser.

b) nstall the rechargeable battery pack into

the laser.

Recharging the battery pack

Plug the adapter into the charging port on the rechargeable battery. The adapter box

charging LED is red during the charging process, and it will turn to green when the battery

is fully charged.

Additional External Power Cables included

1) 12V adapter 2) Car adapter

ote: Recharge the battery when the battery indication shows low or no power.

Ch rging LED on d pter box Ch rging the b ttery p ck

outside the l ser

Ch rging the b ttery p ck

with rech rge ble b ttery

p ck in l ser

Alkaline battery box installation

Rechargeable battery box installation

Using the Optional 40-6391 Adjustable Trivet Stand:

1. When a laser is to be set on a flat surface where the laser beam is not centered in the

pipe, use model 40-6391 Trivet Stand.

2. Using this system, the elevation of the laser beam can be set by either measuring down

from a grade offset hub outside the trench or up from the floor of the manhole to the beam.

The pipe laser can be fixed to the 40-6391 adjustable trivet stand as indicated by the

picture below. Loosen the elevating lock knob to adjust the height, loosen the T LT lock

knob to adjust the T LT angle.

Laser Placement with leg sets:

Choose the different size leg sets for different size pipe. (6” or 150mm (no legs), 8” or

200mm, 10” or 250mm, 12” or 300mm, 15” or 400mm, 21” or 500mm).

For 3 feet support of the pipe laser:

Screw the silver adapter to the hole under the handle of the pipe laser. Attach one leg to

the adapter and two legs to the front of the pipe laser as shown in picture.

7. Using the Product

Keypad Gr de incre se & decre se buttons

Right line - control button

Power button

Gr de enter buttonLCD b cklight & LED button

Gr de setting position button

Left line - control button

Liquid Crystal Display (LCD)

Plus or minus Gr de setting Percent symbol

Leveling st tus Low b ttery

w rning

Line position

Keypad Operating Instructions

Power button

Press the power button to turn on and off the laser. The laser will electronically

self level and display the last grade entered.

LCD backlight and LED button

Power on the laser and press the LCD/LED button . The top green LED will turn on.

The line-axis pivot marker and LED identifies the pivot point for the pipe lasers line

system. The LED also allows you to align a transit over the top of the pipe laser.

Left and Right line control buttons

With the laser powered on, press the left line control button to move the laser beam to the

left and press the right line control button to move the laser beam to the right. The speed

of the line movement increases as the line control button is held.

When the laser dot is moving, the LCD display will show the relevant laser dot position.

A *---- symbol flashing means the laser dot is as far left as it can go.

A -*--- symbol means the laser dot is on the left

A --*-- symbol means the laser dot is centered

A ---*- symbol means the laser dot is on the right

A ----* symbol flashing means the laser dot is as far to the right as it can go.

Center position

After the laser is turned on, pressing the left and right control buttons

simultaneously for one second, will reset the laser line to the center position.

• When the dot is moving to the center position, the LCD will display the following

symbol.

• When the laser dot is centered, the LCD will display the following symbol.

Grade setting position button

Turn the laser on by pressing the power button. The laser will move to the last entered

grade. Press the set button and the (+) or (-) symbol on the LCD will blink. Pressing the

set button again will make the first digit blink. Each additional press of the set button will

make the next digit to the right blink. When the last digit is blinking and the set button is

pressed again, the (+) or (-) symbol will blink.

Grade increase or decrease buttons

n the grade setting mode, with the desired digit blinking, change the grade value by

pressing these buttons. Press the up button to increase the value of the digit. Press the

down button to decrease the value of the digit. Holding the button in will change the

value quickly.

Holding the together will set the grade value to “0”.

--*--

Grade enter button

After the desired grade has been entered on the LCD, press the grade enter button. The

laser beam will move to the new grade value. When the laser is self-leveling, the grade

value symbol will flash and will stop flashing when the laser is level.

Out of level alarm (Front and back)

f the laser is placed beyond its self-leveling range, the laser beam will blink and the LCD

symbol will blink. The laser will need to be repositioned within its self-leveling range as

noted below.

When LCD shows: user needs to lower the handle side.

When LCD shows: user needs to raise the handle side.

Out of level (right and left)

The LCD has a bubble symbol which is used to indicate the right or left out of level status.

f the laser is out of level to the right or left, it will effect its accuracy. Place the laser so

the bubble symbol is centered.

f the LCD symbol flashes, it means the left side of laser is beyond the allowed

range and the left side needs to be lowered.

f the LCD symbol does not flash, it means the left side of laser is high but still in

the allowed range.

This symbol means the laser is level and is in its idea accuracy and working

status.

f the LCD symbol does not flash, it means the ride side of laser is high but still in

the allowed range.

f the LCD symbol flashes, it means the right side of laser is beyond the allowed

range and the right side needs to be lowered.

Otros manuales para 40-6690

Tabla de contenidos

Otros manuales de Nivel láser de Johnson

Johnson

Johnson 40-6688 Manual de usuario

Johnson

Johnson 1760-2400 Manual de usuario

Johnson

Johnson 40-6080 Manual de usuario

Johnson

Johnson 40-0915 Manual de usuario

Johnson

Johnson 40-6551 Manual de usuario

Johnson

Johnson 1880-2400 Manual de usuario

Johnson

Johnson 40-6080 Manual de usuario

Johnson

Johnson 40-6060 Manual de usuario

Johnson

Johnson 40-6647 Manual de usuario

Johnson

Johnson 40-0918 Manual de usuario

Johnson

Johnson 40-6065 Manual de usuario

Johnson

Johnson 40-6616 Manual de usuario

Johnson

Johnson Hot Shot 40-0917 Instrucciones de uso

Johnson

Johnson 40-6650 Manual de usuario

Johnson

Johnson 40-6692 Manual de usuario

Johnson

Johnson 40-6650 Manual de usuario

Johnson

Johnson 1876-2400 Manual de usuario

Johnson

Johnson 40-6692 Manual de usuario

Johnson

Johnson 5700-0800LZR Manual de usuario

Johnson

Johnson JLX LEVEL UP 40-6681 Manual de usuario

Johnson

Johnson 40-6065 Manual de usuario

Johnson

Johnson 40-6250 Instrucciones de funcionamiento y mantenimiento

Johnson

Johnson 40-6690 Manual de usuario

Johnson

Johnson 40-6532 Manual de usuario

Manuales populares de Nivel láser de otras marcas

Nedo

Nedo ET-5 Manual de usuario

geo-FENNEL

geo-FENNEL Maxi-Liner FL 65 HP Manual de usuario

LaserLiner

LaserLiner X2-Laser Manual de usuario

Spectra

Spectra LL300N Manual de usuario

geo-FENNEL

geo-FENNEL Selection PRO FLG 40-PowerCross GREEN SP Manual de usuario

Nedo

Nedo Crossliner 4 Manual de usuario

Lasertec

Lasertec FX360G Manual de usuario

Flex

Flex ALC 8 Manual de usuario

Black & Decker

Black & Decker LZR5 Manual de usuario

Cocraft

Cocraft HL 20-SG Manual de usuario

Zircon

Zircon iLine Manual de usuario

HWH

HWH 310 SERIES Manual de usuario

Leica

Leica iCON robot 60 Manual de usuario

LaserLiner

LaserLiner SuperCross-Laser SCL 2 Manual de usuario

LaserLiner

LaserLiner ActiveFinder XP Manual de usuario

DeWalt

DeWalt DW082 Manual de usuario

imex

imex EL20 Manual de usuario

Fixturlaser

Fixturlaser NXA D I-0912 Manual de usuario