Johnson 40-0918 Manual de usuario

Manual-Leveling Rotary Laser Kit

Model No. 40-0918

Instruction Manual

Congratulations on your choice of this Manual-Leveling Rotary Laser Kit.

We suggest you read this instruction manual thoroughly before using the

instrument. Save this instruction manual for future use.

This is a Class IIIa laser tool and is manufactured to comply with CRF 21,

parts 1040.10 and 1040.11 as well as international safety rule IEC 285.

6696H-English_Manuals 1/31/13 10:32 AM Page 1

Table of Contents

1. Kit Contents

2. Features and Functions

3. Safety Instructions

4. Location/Content

of Warning Labels

5. Location of Parts/Components

6. Operating Instructions

7. Using the Product

8. Self-Check & Fine Calibration

9. Technical Specifications

10. Application Demonstrations

11. Care and Handling

12. Product Warranty

13. Warranty Registration

14. Accessories

1. Kit Contents

Description for Model 40-0918 ty.

Manual-Leveling Rotary Laser

Elevating Tripod 1

Tinted Glasses 1

“AA” Alkaline Batteries 4

Instruction Manual with Warranty Card 1

Hard-Shell Carrying Case 1

2. Features and Functions

• Manual level in horizontal and vertical planes.

• Simultaneous 90º split beam in vertical mode.

• Illuminated vials for easy reading in all conditions.

• Variable rotation speed from 0-600 rpm.

6696H-English_Manuals 1/31/13 10:32 AM Page 2

3. Safety Instructions

Please read and understand all of the following instructions, prior

to using this tool. Failure to do so, may void the warranty.

DANGER!

Class IIIa Laser Product

Max. Power Output: ≤5mW

Wavelength: 640nm-660nm

THIS TOOL EMITS LASER RADIATION.

DO NOT STARE INTO BEAM.

AVOID DIRECT EYE EXPOSURE.

ATTENTION IMPORTANT

• Read all instructions prior to operating this laser tool. Do not remove any labels from tool.

• Do not stare directly at the laser beam.

• Do not project the laser beam directly into the eyes of others.

• Do not set up laser tool at eye level or operate the tool near a reflective surface as

the laser beam could be projected into your eyes or into the eyes of others.

• Do not place the laser tool in a manner that may cause someone to unintentionally

look into the laser beam. Serious eye injury may result.

• Do not operate the tool in explosive environments, i.e. in the presence of gases or

flammable liquids.

• Keep the laser tool out of the reach of children and other untrained persons.

• Do not attempt to view the laser beam through optical tools such as telescopes as

serious eye injury may result.

• Always turn the laser tool off when not in use or left unattended for a period of time.

• Remove the batteries when storing the tool for an extended time (more than 3 months)

to avoid damage to the tool should the batteries deteriorate.

• Do not attempt to repair or disassemble the laser tool. If unqualified persons attempt

to repair this tool, warranty will be void.

• Use only original ohnson®parts and accessories purchased from your ohnson®

authorized dealer. Use of non- ohnson®parts and accessories will void warranty.

6696H-English_Manuals 1/31/13 10:32 AM Page 3

4. Location/Content of Warning Labels

6696H-English_Manuals 1/31/13 10:32 AM Page 4

5. Location of Part/Components

Rotary Head

Base with Tripod

Thread and

Wall-Mounting

Bracket

1 - Vertical (plumb)

Vial “Z”

“Z” Leveling Screw

On/Off Switch and

Variable Speed

Control Knob

2 - Horizontal

(level) Vial “X”

and “Y”

Rotating Beam

Output Window

“X” Leveling Screw

“Y” Leveling

Screw

90º Split Beam

Output Window

6696H-English_Manuals 1/31/13 10:32 AM Page 5

IMPORTANT: It is the responsibility of the user to verify the

calibration of the instrument before each use.

Battery Installation

Unscrew the cover on the back top of the unit and insert four (4) AA

batteries (included). Follow polarity on housing.

Note: Used/discharged batteries are hazardous waste and must be

disposed of properly.

Tripod Set-up

Open up the tripod and position it firmly on a surface that is even

and as near level as possible. For uneven surfaces and inclines,

compensate by adjusting the telescoping legs of the tripod. Tightly

screw the unit and tripod together.

The rotary laser can be used either with the tripod or independently.

Leveling the Laser

Bring the unit into a level position by means of the horizontal “X” and

“Y” adjusting screws (top mounted vials for horizontal application)

and one (1) vertical “Z” adjusting screw (one side mounted vial for

vertical application).

To obtain accurate measures, use the leveling screws found on the

mounting base and ensure that the bubble in each vial is perfectly

centered.

6. Operating Instructions

6696H-English_Manuals 1/31/13 10:32 AM Page 6

7. Using the Product

To turn on, rotate the on/off and variable speed switch in the

direction indicated by the arrow. Use this on/off and variable speed

control knob to create a single laser point or an intermittent line or

a continuous line. The slower the rotation, the more visible the

beam will be. If used with an optional detector, use fastest rotation

speed.

Note: Due to the 360° rotating feature of the laser beam, extra care

must be taken to avoid direct contact with the eyes.

6696H-English_Manuals 1/31/13 10:32 AM Page 7

8. Self-Check & Fine Calibration

IMPORTANT: It is the responsibility of the user to verify the

calibration of the instrument before each use.

Checking for Accuracy:

1. Start by placing the laser 1’ away from a wall (near wall), and

at least 20’ from a wall (far wall).

2. Align the laser so that one axis (vial) points to both walls.

3. Turn the laser on and adjust the thumbscrews until the unit is

level in both the X and Y axis.

4. Make a mark where the laser hits the near wall (wall #1), and

then the same for the far wall (wall #2).

5. Next, move the laser to 1’ next to the far wall, and ensure it is

in the same axis.

6. Level the laser, and then adjust the height so that the laser is

level and hits the mark you made on the far wall (wall #2).

You may need to re-level to achieve this.

Vertical Line

Horizontal Reference Line

Wall

Platform

6696H-English_Manuals 1/31/13 10:32 AM Page 8

7. Then walk over to the original near wall (wall #1) and measure

the difference between the original mark and the laser line. If

the value is more than 1/8” at 30’, then calibration is required.

8. Ensure accuracy is verified for both the X and Y axis.

Note: X and Y axis are determined by the end user, either vial can be

considered X/Y.

Adjusting Accuracy:

1. Measure the difference between the original near wall mark

(wall #1) and where the laser is hitting the near wall.

2. Walk back to the far wall (wall #2) and adjust the laser so that

it is halfway between the two near wall marks (pencil mark

and laser mark).

3. Next, remove the screw cap for the vial for the axis you are

working with, and using a 2.5mm hex tool, adjust the vial so

that it appears level.

Inner Hexagon Spanner

Y-Direction Level

Calibration Hole

X-Direction Level

Calibration Hole

X-Direction Level

6696H-English_Manuals 1/31/13 10:32 AM Page 9

9. Technical Specifications

Laser Wavelength 650nm±10nm

Laser Classification Class IIIa

Maximum Power Output ≤5mW

Accuracy ±1/8"/30 ft. (±0.3mm/m)

Interior Range Up to 200 ft. (60m) diameter depending

upon light conditions

Power Supply 4 “AA” alkaline batteries (included)

Battery Life

Approx. battery life 25 hours continuous use

Dimensions 4.75" x 4.75" x 6.125"

(120 x 120 x 156mm)

Weight 1.35 lbs (0.6Kg)

Working Temperature 14°F to 113°F (-10°C to +45°C)

Center screw thread 5/8" – 11

Rotation Speed 0-600 rpm

IP Protection Class 43

6696H-English_Manuals 1/31/13 10:32 AM Page 10

Tabla de contenidos

Otros manuales de Nivel láser de Johnson

Johnson

Johnson 40-6584 Manual de usuario

Johnson

Johnson 9100 Manual de usuario

Johnson

Johnson 40-6674 Manual de usuario

Johnson

Johnson 40-6936 Manual de usuario

Johnson

Johnson 40-6060 Manual de usuario

Johnson

Johnson 40-6065 Manual de usuario

Johnson

Johnson 40-6616 Manual de usuario

Johnson

Johnson 1888-0700 Manual de usuario

Johnson

Johnson 40-6535 Manual de usuario

Johnson

Johnson 1880-2400 Manual de usuario

Johnson

Johnson 40-6692 Manual de usuario

Johnson

Johnson 40-6620 Manual de usuario

Johnson

Johnson 40-6692 Manual de usuario

Johnson

Johnson 40-6250 Manual de usuario

Johnson

Johnson 40-6636 Manual de usuario

Johnson

Johnson 40-6926 Manual de usuario

Johnson

Johnson 40-6080 Manual de usuario

Johnson

Johnson 40-6670 Manual de usuario

Johnson

Johnson 40-6060 Manual de usuario

Johnson

Johnson 1876-2400 Manual de usuario

Johnson

Johnson 40-6184 Manual de usuario

Johnson

Johnson 40-6688 Manual de usuario

Johnson

Johnson JLX LEVEL UP 40-6681 Manual de usuario

Johnson

Johnson 40-6685 Manual de usuario

Manuales populares de Nivel láser de otras marcas

Nedo

Nedo ET-5 Manual de usuario

geo-FENNEL

geo-FENNEL Maxi-Liner FL 65 HP Manual de usuario

LaserLiner

LaserLiner X2-Laser Manual de usuario

Spectra

Spectra LL300N Manual de usuario

geo-FENNEL

geo-FENNEL Selection PRO FLG 40-PowerCross GREEN SP Manual de usuario

Nedo

Nedo Crossliner 4 Manual de usuario

Lasertec

Lasertec FX360G Manual de usuario

Flex

Flex ALC 8 Manual de usuario

Black & Decker

Black & Decker LZR5 Manual de usuario

Cocraft

Cocraft HL 20-SG Manual de usuario

Zircon

Zircon iLine Manual de usuario

HWH

HWH 310 SERIES Manual de usuario

Leica

Leica iCON robot 60 Manual de usuario

LaserLiner

LaserLiner SuperCross-Laser SCL 2 Manual de usuario

LaserLiner

LaserLiner ActiveFinder XP Manual de usuario

DeWalt

DeWalt DW082 Manual de usuario

imex

imex EL20 Manual de usuario

Fixturlaser

Fixturlaser NXA D I-0912 Manual de usuario