Johnson Controls TM-2161 Manual de usuario

TM-21x1 Series Room Temperature Module Installation Instructions 1

Applications

The TM-21x1 Series of Room Temperature Modules

are designed for use with the Facility Explorer Series of

field controllers. The setpoint dial enables the room

occupant to adjust the working setpoint of the

controller. On scaled models, the marked adjustment

range is 55 to 85°F; the controller determines the

actual setpoint temperature. On Warmer/Cooler

models, the adjustment range is marked +/- from

midpoint of the dial; the controller determines the

equivalent setpoint temperature.

With the occupancy button, the occupant can switch

the controller’s operating mode between occupied and

standby. In addition, the TM-21x1 Series offers the

option of a temporary occupied mode during

unoccupied mode.

The TM-21x1 Series Room Temperature Module also

features a Light-Emitting Diode (LED) that indicates the

current operating mode.

Installation

Parts Included

Two #6-32 x 7/8 in. (22 mm) wallbox mounting screws

are included with the TM-21x1 Module.

Special Tools Needed

For tightening and loosening the TM-11x1 Series Room

Temperature Module security screw, order the optional

Allen-head tool (T-4000-119) from the nearest

Johnson Controls® representative.

IMPORTANT: The TM-21x1 Series Room

Temperature Modules are intended to provide an

input to equipment under normal operating

conditions. Where failure or malfunction of the

TM-21x1 Temperature Module could lead to

personal injury or property damage to the controlled

equipment or other property, other precautions must

be designed intothe control system. Incorporate and

maintain other devices, such as supervisory or

alarm systems or safety or limit controls, intended to

warn of or protect against failure or malfunction of

the TM-21x1 Temperature Module.

TM-21x1 Series Room Temperature Module

Installation Instructions Part No. 24-10225-12, Rev. C

Issued March 2016

24- 10225- 12, Rev. C

TM-21x1 Series Room Temperature Module Installation Instructions2

Dimensions

TM-2141 Modules

TM-2151 Modules

TM-2161 Modules

Figure 1: TM-2141 Dimensions, in. (mm)

3.15 (80)

1.26 (32)

4.72

(120)

FIG:2141_dim

Figure 2: TM-2151 Dimensions, in. (mm)

FIG:2151_dim

Mode

LED

Occupancy

Button

3.15 (80)

1.26 (32)

4.72

(120)

Figure 3: TM-2161-0002 and TM-2161-0007

Dimensions, in. (mm)

FIG:2161_dim

1.38 (35)

4.72

(120)

3.15 (80)

Mode

LED

Occupancy

Button

Fan

Speed

Dial

Setpoint

Adjustment

Dial

FIG:2161_0005_dim

1.38 (35)

4.72

(120)

3.15 (80)

Mode

LED

Occupancy

Button Setpoint

Adjustment

Dial

Figure 4: TM-2161-0000 and TM-2161-0005

Dimensions, in. (mm)

TM-21x1 Series Room Temperature Module Installation Instructions 3

TM-2191 Modules

Installing the TM-21x1

To install the TM-21x1 Series Room Temperature

Module:

1. Use the Allen-head tool to loosen the security

screw located at the top center of the housing.

2. Insert a screwdriver blade or coin into the slot on

the top of the housing.

3. Press down gently, and pry the housing away from

the base. As the two parts separate, remove the

blade or coin and continue to pull the housing away

from the base until the housing is free.

4. Pull the wires through the base. Locate the green

terminal blocks in the upper right of the base and

position the module on the wallbox with the

terminal numbers right-side up.

5. Mount the base to the wallbox using the two #6-32

mounting screws (included).

6. Wire the controller to the module. See the Wiring

section for correct wiring.

7. Attach the housing to the base and tighten the

security screw with the allen-head tool.

Mounting

Location Considerations

Mount the TM-21x1 Series Room Temperature Module

on a wall in the room to be controlled where the

occupant can easily read and adjust the setpoint dial or

fan speed override adjustment dial. Consider these

additional guidelines in determining the best mounting

location:

• Avoid areas subject to excessive vibration,

electrical noise, direct sunlight, or the effects of

radiant heat.

• Keep electrical wiring as short as possible to

minimize temperature error.

• Install modules in areas where the temperature is

representative of the general room conditions.

Wiring

To wire a controller to the TM-21x1 Series Room

Temperature Module, see the appropriate wiring

diagram (Figure 6 to Figure 10).

Note: Use 22 AWG (0.65 mm diameter) wire

minimum. Do not exceed 164 ft (50 m) between the

controller and the temperature module.

Figure 5: TM-2191 Dimensions, in. (mm)

FIG:2191_dim

3.15 (80)

1.38 (35)

4.72

(120)

Setpoint

Adjustment

Dial

Table 1: Nominal Values for 10k ohm Sensors

Temperature Resistance

FCohm

20 -7 48,525

30 -1 34,919

40 4 27,550

50 10 19,898

60 16 12,246

70 21 11,993

80 27 9,222

90 32 7,510

100 38 5,874

110 43 4,871

120 49 3,956

130 54 3,277

TM-21x1 Series Room Temperature Module Installation Instructions4

TM-2141-0000

TM-2151-0000

TM-2161-0000 and TM-2161-0005

TM-2161-0002 and TM-2161-0007

TM-2191-0000 and TM-2191-0005

Figure 6: Wiring to an NTC Room Sensor

FIG:2141_WIR

NTC Sensor

Common

Room Temperature

Module

Figure 7: Wiring to a Room Temperature Module

Featuring an NTC Sensor with Occupancy

Override

FIG:2151_WIR

NTC Sensor

Common

Mode LED

Occupancy Button

Room Temperature

Module

Figure 8: Wiring to a Room Temperature Module

Featuring an NTC Sensor with Temperature

Setpoint Adjustment, and Occupancy Override

FIG:2161_0005_WIR

NTC Sensor

Common

Mode LED

Occupancy Button

Room Temperature

Module

DC +5 V

Temperature Setpoint

Figure 9: Wiring to a Room Temperature Module

Featuring an NTC Sensor with Temperature

Setpoint Adjustment, Occupancy Override, and

Three Speed Fan Override

FIG:2161_0207_WIR

20 NTC Sensor

Common

Mode LED

Occupancy Button

22 DC +5 V

Temperature Setpoint

Room Temperature

Module

51 Three-Speed Fan

Override

Figure 10: Wiring to a Room Temperature Module

Featuring an NTC Sensor without Occupancy

Override

FIG:2191_WIR

NTC Sensor

Common

Room Temperature

Module

DC +5 V

Temperature Setpoint

TM-21x1 Series Room Temperature Module Installation Instructions 5

The following messages apply to wiring this product.

Setup and Adjustments

Make temperature or fan speed adjustments using the

rotating dial, shown in Figure 3 and Figure 5.

Repair Information

Do not field repair the TM-21x1 Series Room

Temperature Module. As with any electrical device,

keep the air vents clean and free from dust and

obstruction. To order replacement parts, contact the

nearest Johnson Controls representative.

CAUTION: Risk of Electric Shock.

Disconnect power supply before making

electrical connections to avoid electric

shock.

Mise En Garde: Risque de décharge

électrique. Débrancher l'alimentation

avant de réaliser tout raccordement

électrique afin d'éviter tout risque de

décharge électrique.

CAUTION: Risk of Property Damage.

Do not run low voltage cable in the same

conduit or wiring troughs with high

voltage wires. Running low and high

voltage wires in the same conduit or

wiring troughs may damage the

equipment or cause system malfunction.

MISE EN GARDE : Risque de dégâts

matériels.

Ne pas faire courir un câble basse

tension dans les mêmes gaines ou

goulottes électriques que des câbles

haute tension. L'installation de fils basse

tension et haute tension dans les mêmes

gaines ou goulottes électriques risque

d'endommager l'équipement ou de

provoquer des dysfonctionnements du

système.

CAUTION: Risk of Property Damage.

Do not apply power to the system before

checking all wiring connections. Short

circuited or improperly connected wires

may result in permanent damage to the

equipment.

Mise En Garde: Risque de dégâts

matériels. Ne pas mettre le système

sous tension avant d'avoir vérifié tous les

raccords de câblage. Des fils formant un

court-circuit ou connectés de façon

incorrecte risquent d'endommager

irrémédiablement l'équipement.

IMPORTANT: Use copper conductors only. Make

all wiring connections in accordance with local,

national, and regional regulations. Do not exceed

the Temperature Module electrical ratings.

TM-21x1 Series Room Temperature Module Installation Instructions6

Technical Specifications

TM-21x1 Series Room Temperature Module (Part 1 of 2)

Models TM-2141-0000 Temperature Output Only

TM-2151-0000 Temperature Output with Occupancy Override

TM-2161-000x Temperature Output with Setpoint Adjustment and Occupancy

Override and Optional Fan Speed Adjustment

TM-2191-000x Temperature Output with Setpoint Adjustment

Power Requirements 5 VDC

Power Consumption N/A: Refer to individual component specification.

Inputs None

Adjustments Temperature Setpoint, Fan Speed (Optional by Model)

Mode Indicator Green LED (5 V, 4 mA)

Occupancy Button Momentary Contact Switch, 5 V at 1 mA

Output Temperature Sensing

Element Resistance Temperature Device (RTD) Thermistor Negative

Temperature Coefficient (NTC) 10k ohm at 77°F (25°C)

Fan Speed 10k ohm potentiometer, with mechanically guided positions at

0, 25, 50, 75, 100% for Auto, Off, I (low speed),

II (medium speed), and III (high speed)

Published in U.S.A. www.johnsoncontrols.com

TM-21x1 Series Room Temperature Module Installation Instructions 7

Metasys® and Johnson Controls® are registered trademarks of Johnson Controls, Inc.

Building Efficiency

507 E. Michigan Street, Milwaukee, WI 53202

The performance specifications are nominal and conform to acceptable industry standards. For application at conditions beyond these

specifications, consult the local Johnson Controls office. Johnson Controls, Inc. shall not be liable for damages resulting from misapplication or

misuse of its products.

Setpoint Range TM-2141-0000

TM-2151-0000 No setpoint range

TM-2161-0000

TM-2191-0000 10k ohm potentiometer marked for 55 to 85°F

TM-21x1-0002 10k ohm potentiometer marked for 55 to 85°F

Fan Speed Adjustment: Auto, Off, I, II, and III

TM-21x1-0005 10k ohm potentiometer marked for +/- (5F°)

TM-21x1-0007 10k ohm potentiometer marked for +/- (5F°)

Fan Speed Adjustment: Auto, Off, I, II, and III

Accuracy ±0.9°F (±0.5°C)

Field Connection 18 to 22 AWG (1.00 to 0.65 mm diameter) recommended

Mounting Wallbox Mount

Housing Material ABS + PC, Self-Extinguishing HB UL94

Protection IP30 (EN 60529)

Ambient Operating Conditions 32 to 122°F (0 to 50°C)

10 to 90% RH, noncondensing

Ambient Storage Conditions -40 to 158°F (-40 to 70°C)

5 to 95% RH, noncondensing

Dimensions

(H x W x D) TM-2141

TM-2151 4.72 x 3.15 x 1.26 in.

(120 x 80 x 32 mm)

TM-2161

TM-2191 4.72 x 3.15 x 1.38 in.

(120 x 80 x 35 mm)

Shipping Weight 0.44 lb (0.2 kg)

Compliance Europe CE Mark: EMC Directive, EN-61000-6-2

European Single Point of Contact: NA/SA Single Point of Contact: APAC Single Point of Contact:

JOHNSON CONTROLS

WESTENDHOF 3

45143 ESSEN

GERMANY

JOHNSON CONTROLS

507 E MICHIGAN ST

MILWAUKEE WI 53202

USA

JOHNSON CONTROLS

C/O CONTROLS PRODUCT

MANAGEMENT

NO. 22 BLOCK D NEW DISTRICT

WUXI JIANGSU PROVINCE 214142

CHINA

TM-21x1 Series Room Temperature Module (Part 2 of 2)

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Controladores de temperatura de Johnson Controls

Johnson Controls

Johnson Controls PENN A70 Series Manual de usuario

Johnson Controls

Johnson Controls WRZ-7860-0 Manual de usuario

Johnson Controls

Johnson Controls A70 Series Manual de usuario

Johnson Controls

Johnson Controls A11A Manual de usuario

Johnson Controls

Johnson Controls TE-6800 Series Manual de usuario

Johnson Controls

Johnson Controls TE-631xM Manual de usuario

Johnson Controls

Johnson Controls TE-63xS Series Manual de usuario

Johnson Controls

Johnson Controls W43A Manual de usuario

Johnson Controls

Johnson Controls System 350T A350P Manual de usuario

Johnson Controls

Johnson Controls TM-11x1 series Manual de usuario

Johnson Controls

Johnson Controls MS4PMUHVT Manual de usuario

Johnson Controls

Johnson Controls T606MSP-4 Manual de usuario

Johnson Controls

Johnson Controls A419 Series Manual

Johnson Controls

Johnson Controls TE-6800 Series Manual de usuario

Johnson Controls

Johnson Controls MS2 Manual

Johnson Controls

Johnson Controls A19D Manual de usuario

Johnson Controls

Johnson Controls A419ABG-3C Manual de usuario

Johnson Controls

Johnson Controls TE730 Series Manual de usuario

Johnson Controls

Johnson Controls FX-WRZ Series Manual de usuario

Johnson Controls

Johnson Controls A419 Series Manual de usuario

Johnson Controls

Johnson Controls A11D Manual de usuario

Johnson Controls

Johnson Controls System 350 A350A Manual de servicio

Manuales populares de Controladores de temperatura de otras marcas

Swegon

Swegon LUNAd MB Manual de usuario

Lucky Reptile

Lucky Reptile Thermo Control II Manual de usuario

SENSORMETRIX

SENSORMETRIX Argon 100 Manual de usuario

Fuji Electric

Fuji Electric PXE4 Manual de usuario

Yuyao gongyi

Yuyao gongyi XMT-808 series Manual de usuario

Selec

Selec TC544C Manual de usuario

P.W. KEY

P.W. KEY rt-208gt Manual de usuario

Future Design

Future Design FDC-9200 Manual de usuario

BH Thermal

BH Thermal BriskONE Manual de usuario

Omron

Omron E5EX-H Manual de usuario

West Control Solutions

West Control Solutions KS 45 Guía de inicio rápido

MCS

MCS RITC-15B Manual de usuario

SMC Networks

SMC Networks Thermo-con INR-244-639 Manual de usuario

eltherm

eltherm Ex-TC It Series Manual de usuario

Omron

Omron C200H-TV Series Manual de usuario

industrie technik

industrie technik CA1 Manual de usuario

KRAL

KRAL EET 32 Manual de usuario

dixell

dixell XR420C Diagrama de cableado