Johnson Controls IQ WiFi 6 Manual de usuario

IQ WiFi 6 QUICK INSTALL GUIDE

SKU: IQWF6

Description: IQWIFI6

Dimensions: 151.4 mm x 150.4 mm x 55.4 mm

Weight: 425g

Usage: For Indoor use only

Compliance: FCC, UL, CE

Processor: Qualcomm IPQ6000

Flash Memory: 512MB NAND

Memory: 512MB DDR3-933MHz

Operating Temperature: 0°C - 40°C (32°F - 104°F)

Relative Humidity: 10% - 90% RH (non-condensing)

Operating Distance: Up to 130ft

Frequency Type:

Wireless IEEE 802.11 b/g/n/ax 2.4GHz

IEEE 802.11 a/n/ac/ax 5GHz

Wired Type:

LAN and WAN Gigabit Ethernet Ports

LED Indicators:

2 color LED (Green and Red): Power/Status

Green LEDs: WAN, SmartHome, LAN

Power Supply:

Input: 100-240VAC, 50-60Hz

Output: 1.5A 18.0W

SPECIFICATIONS

FEATURES & OVERVIEW

This is a quick guide for experienced installers only. Refer to http://qolsys.com

The IQ WiFi 6 is a mesh capable

router that covers every corner of

every room with safe, seamless WiFi.

Features:

•Self optimizing WiFi mesh with

wired and wireless ethernet

backhaul

•WiFi version 6, ax1800

•Supports Dual-band 2.4G/5G

•Supports 7 additional Agents (1

Controller)

•Stand alone or parallel

configuration supported

•Web interface or IQ Panel

configurable

•Main, Guest and Security SSIDs

•Included wall mount enabled

flexible placement

IQ WiFi 6 QUICK INSTALL GUIDE

SUPPORT

INCLUDED IN THE BOX

This is a quick guide for experienced installers only. Refer to http://qolsys.com

Mounting Bracket

IQ WiFi 6

Power Supply

Ethernet

Cable

Note: The Low-Voltage IQ WiFi Mount is designed to

mount onto a low-voltage single gauge back-box or to be

mounted with drywall anchors. DO NOT MOUNT ON A

HIGH VOLTAGE BOX. If pairing with a low-voltage box

use size 6 screws (M3.5) that are 1 inch (2.54 cm) in length.

CONNECT THE IQ WiFi 6

STEP

POWER UP THE IQ WiFi 6

STEP

This is a quick guide for experienced installers only. Refer to http://qolsys.com

STEP

CONNECT TO THE MODEM OR EXISTING NETWORK

1. Plug the barrel jack end of the

power supply into the “DC-IN” port.

Do not plug in the power supply

into outlet until step 3.

2. Connect the provided ethernet

cable into the “WAN” port.

Connect the opposite end of the provided

ethernet cable into the “ETHERNET” port on the

modem*.

Plug in your power supply to

the wall outlet. Router takes

up to 4 minutes to power up,

the power LED will stop

flashing when ready.

* Note: when powered for the

first time and connected to

internet, LED’s may flash for up

to 5 minutes indicating an auto

update.

*Note: for parallel installs plug the

ethernet cable into an available port

on the customer’s existing router (see

additional considerations)

STEP

ADD ALL AGENTS

1. Power up an additional IQ WiFi 6 (see

step 3).

2. Using the supplied ethernet cable,

connect one end into the LAN port of the

Controller

3.Connect the opposite end of the same

ethernet cable into the LAN port of the

Agent.

Note: No additional button press or manual

conﬁguration needed. LET PROCESS

FINISH, COULD TAKE UP TO 10 MINUTES

to auto conﬁgure.

MODEM/ROUTER

Controller

Agent

PAIR CONTROLLER TO IQ PANEL

STEP

RENAME YOUR NETWORK (SSID)

STEP

This is a quick guide for experienced installers only. Refer to http://qolsys.com

1. Open settings tray from IQ Panel

> Settings > Advance Settings >

type in valid code > touch

Installation > Devices > WiFi

devices > IQ WiFi icon

2.Touch the down arrows to make

edits to the Network Name (SSID’s)

STEP

CREATE UNIQUE SSID AND PASSWORD

1. Enter a unique

network name

2.Enter a unique

security key

3. Touch Save

1. Open settings tray,

touch Settings >

Advanced settings >

type valid dealer or

install code > WiFi.

2. Look for the

broadcasting SSID

or network name

and touch it. SSID

will be

IQ_WiFi_XXXXXX

3.Enter password

printed on sticker or

bottom of router.

4.Touch connect

*Note: network SSID cannot contain &( ) | < > , ‘ spaces or backslash.

*Note: IQ WiFi 6 will use the same SSID

for both bands 2.4GHz and 5GHz

Document#: IQWIFI6-IM

Revision Date: 2021-11

[email protected]

Johnson Controls proprietary.

Reproduction without permission is not permitted.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired

operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation

of the device.

Cet appareil est conforme avec Industrie Canada exempts de licence standard RSS (s). Son fonctionnement est soumis aux deux conditions suivantes: (1) cet appareil ne doit pas provoquer d'interférences et (2) cet appareil doit accepter toute interférence, y compris celles pouvant

causer un mauvais fonctionnement de l'appareil.

CONTACT TECH SUPPORT

GOT QUESTIONS?

TROUBLESHOOTING

ADDITIONAL CONSIDERATIONS

Factory Default:

- Press and hold the physical reset button for at least 10 seconds

then release. Release when LED goes solid.

You can set up the IQ WiFi 6 in either of these ways:

As the only wireless network on the premises:

In parallel with an existing wireless network:

Great for:

-Improving connectivity for ALL WiFi devices on

the network.

-Offering support for the entire network.

Great for:

-Keeping the security and smart-home devices

private/hidden from the rest of the WiFi connected

devices on the network.

-Making online/remote support easier as only

known/authorized devices should be connected.

-Ensuring better connectivity for dealer supported

devices.

LED Status:

Otros manuales para IQ WiFi 6

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Enrutador de red de Johnson Controls

Johnson Controls

Johnson Controls ZFR1812 Manual de usuario

Johnson Controls

Johnson Controls ZFR1811 Manual de usuario

Johnson Controls

Johnson Controls WT-ROUTER Manual de usuario

Johnson Controls

Johnson Controls ZFR1831 Pro Series Manual de usuario

Johnson Controls

Johnson Controls Intelligent Fire Integrator ROUTMB Manual de usuario

Johnson Controls

Johnson Controls IQ WiFi 6 Manual de usuario

Johnson Controls

Johnson Controls TL-BRTRP-0 Manual de usuario

Johnson Controls

Johnson Controls IQ WiFi 6 Manual de usuario

Johnson Controls

Johnson Controls WRG1830 Manual de usuario

Manuales populares de Enrutador de red de otras marcas

Allnet

Allnet ALL0333AU Manual de usuario

HomeSeer

HomeSeer HT-SEL Manual de usuario

Sercomm

Sercomm Genesis OC3505D Manual de usuario

Billion

Billion BIPAC 5102 Series Manual de usuario

TP-Link

TP-Link TD-8817 Manual de usuario

Motorola

Motorola MR1900 Manual de usuario

Digi

Digi IX14 Manual de usuario

Cisco

Cisco NCS 540 Manual

XAVi

XAVi X8821e Manual de usuario

BEC

BEC 6200WZL Manual de usuario

MikroTik

MikroTik hAP ac3 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

NETGEAR

NETGEAR FS526T - Switch Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Automated Logic

Automated Logic ZN551 Manual del propietario

Cisco

Cisco ASR 1000 Series Manual del operador

EnGenius

EnGenius ESR-9710 Manual de usuario

Cisco

Cisco 805 Series Instrucciones de funcionamiento y seguridad