Johnson Controls Metasys BTCVT Manual de usuario
Metasys® CCT Bluetooth® Technology
Communication Commissioning Guide
LIT-12011038Building Technologies & Solutions
www.johnsoncontrols.com
2019-05-27
Contents
ContentsDocument Introduction................................................................................................................. 3
Bluetooth Wireless Technology Modules and Adapters........................................................... 3
Bluetooth Quick Start Guide......................................................................................................... 4
Setting up the BTCVT Wireless Commissioning Converter............................................................ 4
Bluetooth Quick Start Guide for Windows 7......................................................................... 5
Bluetooth Quick Start Guide for Windows 10....................................................................... 6
Troubleshooting............................................................................................................................. 7
Detailed Procedures....................................................................................................................... 9
Verifying the Connection between the Laptop and the Wireless Commissioning
Converter.................................................................................................................................... 9
Installing the Bluetooth Wireless USB Adapter............................................................................. 11
Related Documentation.............................................................................................................. 13
Document Introduction
This document describes how to install the supported Bluetooth® wireless adapters and
commission your Controller Configuration Tool (CCT) to communicate with the Bluetooth Wireless
Commissioning Converter (BTCVT).
Note: In other documentation, the Bluetooth Commissioning Converter may be referred to as
the Wireless Commissioning Converter.
The procedure described in this document allows your computer to pair with the Wireless
Commissioning Converter. You can pair with more than one Wireless Commissioning Converter, but
you can only connect to one converter at a time.
This document assumes that you have already installed the CCT software on your computer.
The BTCVT Wireless Commissioning Converter used during this procedure should be the one that
you intend to use when uploading and downloading controllers. Please note that when using the
BTCVT, newer field controller models, including those with a release of Metasys 9.0 or later, will not
work with the Transfer to Device (Download) feature in CCT.
CCT supports the Windows® 10, 8.1, Windows 8, and Windows 7 operating systems. Windows XP®
is no longer supported for CCT software at Release 10.1.
Note: You cannot commission your CCT for Bluetooth communication if it is running a server-
class operating system, such as Windows Server® 2008 or Windows Server 2012.
To complete all of the procedures in this document, you must have a Wireless Commissioning
Converter connected to a powered-on field controller (refer to the Wireless Commissioning Converter
Installation Instructions [Part No. 24-10108-2]).
Note: The Wireless Commissioning Converter can be used in conjunction with the ZFR1800
Series Wireless Field Bus System; however, the wireless technologies of the Wireless
Commissioning Converter and the ZFR1800 Series System do not directly interact. When the
Wireless Commissioning Converter is connected on the hard-wired portion of a Field Controller
(FC) Bus, it can be used to commission and communicate with any field controller, whether
it is hardwired to the FC Bus or wirelessly enabled through the ZFR1800 Series Wireless Field
Bus System. When the Wireless Commissioning Converter is connected directly to a wirelessly
enabled field controller, it commissions and communicates with only that controller.
Bluetooth Wireless Technology Modules and
Adapters
Bluetooth allows the CCT software to connect the Wireless Commissioning Converter for uploading
and downloading field controller applications.
The computer that is running CCT must have Bluetooth wireless capabilities to communicate
with the Wireless Commissioning Converter. We recommend that you do not install an external
Bluetooth wireless adapter if Bluetooth technology is already built in.
You can commission the following types of laptop computers to communicate with the Wireless
Commissioning Converter:
• a laptop computer with an internal Bluetooth wireless module
• a laptop or desktop computer with a Bluetooth wireless USB adapter
If you do not have Bluetooth technology built in to your computer and you must install a Bluetooth
wireless USB adapter, see Installing the Bluetooth Wireless USB Adapter for directions. After the
3Metasys® CCT Bluetooth® Technology Communication Commissioning Guide
Bluetooth wireless adapter is installed and configured, you do not need to configure it again until
software or hardware configurations change.
Bluetooth Quick Start Guide
This quick start guide leads you through the Bluetooth device setup for Windows 7 and Windows
10. Your steps may vary depending on the vendor of the Bluetooth wireless device and your
operating system.
You must repeat these steps for each Bluetooth converter you set up, as each device is assigned its
own COM port.
Setting up the BTCVT Wireless Commissioning Converter
1. Plug your BTCVT Wireless Commissioning Converter into the SA BUS port or the FC BUS port on
your field controller.
Figure 1: SA BUS and FC BUS Port
2. On the BTCVT, verify that the Power LED is green, and that the Fault LED is off.
Metasys® CCT Bluetooth® Technology Communication Commissioning Guide4
Figure 2: BTCVT Wireless Commissioning Converter.
3. Verify that your computer's wireless is turned on. Typically, the internal wireless on/off button
is on the side of the laptop or above the keyboard.
Bluetooth Quick Start Guide for Windows 7
To connect the BTCVT with Windows 7, follow these steps:
1. Right-click the Bluetooth icon ( ) in your system tray, and then select Add a Device from the
pop-up menu. The Add a device wizard appears, and Windows searches for devices within
range.
Note: If you do not see the icon in the system tray, click the Show hidden icons
arrow in the tray, click Customize,and then set the Bluetooth item to Show icons and
notifications. Click OK to close the window. The Bluetooth icon is added to your system
tray.
2. Select your Bluetooth device and click Next. The Add a device wizard starts.
Note: Your device's 12 digit MAC address is printed on the case of the device. To identify
your device in the Add a Device wizard, match the address on your BTCVT hardware to
the address listed in the wizard.
3. When you are prompted to enter the pairing code for the device, enter BTCVT. Follow
additional instructions as they appear, and then select Close.
4. Note your device's COM port number. To do this, select Start > Control Panel > Devices and
Printers. Right-click the device, and then click Properties. Select the Hardware tab to find the
COM port number.
5. Launch the CCT and select Transfer > Transfer to Computer (Upload).
6. Select Bluetooth for the connection type, and enter the Bluetooth COM port number that you
discovered in step 4. We recommend you set the Baud Rate to 38400.
Note: The CCT remembers the most recent COM port entry for future uses.
7. Click Next. The wizard displays the status Connecting, and then changes to Connected.
5Metasys® CCT Bluetooth® Technology Communication Commissioning Guide
Note: When Connected appears, the blue LED on the BTCVT device turns on and remains
solid (not flashing), indicating a successful connection to the CCT. The SA/FC on the
BTCVT turns on and flashes, indicating that communications to the field controller are
established.
Bluetooth Quick Start Guide for Windows 10
1. Right-click the Bluetooth icon ( ) in your system tray, and then select Add a Device from
the pop-up menu. Alternatively, go to Start > Settings > Devices > Bluetooth & other devices.
Confirm that Bluetooth is turned on.
2. To pair your device, click on the button Add Bluetooth or other device. The Add a Device
wizard appears.
3. In the Add a Device wizard, click on the first option for Bluetooth. Click on the device to
connect.
Note: Your device's 12 digit MAC address is printed on the case of the device. To identify
your device in the Add a Device wizard, match the address on your BTCVT hardware to
the address listed in the wizard.
4. When you are prompted to enter the pairing code for the device, enter BTCVT. Follow
additional instructions as they appear, and then select Close.
5. Under Related Settings, select More Bluetooth Options to display the Bluetooth Settings
control panel.
6. In the Bluetooth Settings control panel, select the COM Ports tab. Two ports will be listed.
The port that includes COM1 in the name is the port number CCT requires.
Figure 3: Selecting the COM Port
7. Launch the CCT and select Transfer > Transfer to Computer (Upload).
Metasys® CCT Bluetooth® Technology Communication Commissioning Guide6
8. Select Bluetooth for the connection type, and enter the Bluetooth COM port number that you
discovered in step 6. We recommend you set the Baud Rate to 38400.
Note: The CCT remembers the most recent COM port entry for future uses.
9. Click Next. The wizard displays the status Connecting, and then changes to Connected.
Note: When Connected appears, the blue LED on the BTCVT device turns on and remains
solid (not flashing), indicating a successful connection to the CCT. The SA/FC on the
BTCVT turns on and flashes, indicating that communications to the field controller are
established.
Troubleshooting
Table 1: Troubleshooting
Problem Solution
You cannot communicate with the
Wireless Commissioning Converter
from the CCT.
You receive a Connection failed!
alert.
Use the following procedure to verify the computer's
wireless state, verify the COM port, and test the connection
between your computer and wireless device.
1. Verify that your computer's wireless is turned on.
2. Verify that Bluetooth is enabled. In Windows 10, you
can verify that Bluetooth is turned on by going to Start
> Settings > Devices > Bluetooth & other devices. In
both Windows 10 and Windows 7 operating systems,
you can check to see if Bluetooth has been enabled for
the device by going to the Device Manager in Control
Panel. Expand the Bluetooth section to view a list of all
connected Bluetooth devices.
3. Verify the COM port. In Devices and Printers, right-
click the device, and then click Properties. Select the
Hardware tab to find the COM port number.
4. Test the connection and signal quality between your
computer and the Wireless Commissioning Converter.
See Verifying the Connection between the Laptop and
the Wireless Commissioning Converter.
7Metasys® CCT Bluetooth® Technology Communication Commissioning Guide
Table 1: Troubleshooting
Problem Solution
The computer does not communicate
properly with the Bluetooth wireless
USB adapter.
If you plug in the Bluetooth wireless USB adapter
before the installation software prompts you to do so,
the computer may install its own drivers and may not
communicate properly with the Bluetooth wireless
USB adapter. If this occurs, use the following recovery
procedure:
1. Unplug the Bluetooth wireless USB adapter.
2. On the Start menu, go to Run or press the Windows
key + R. In the Run dialog box, type %windir%\inf.
3. Rename the BTH.inf file to BTH.bak.
4. Uninstall the Bluetooth software by using the
Programs and Features option in Control Panel.
5. Restart the computer.
6. Reinstall the Bluetooth wireless USB adapter. See
Installing the Bluetooth Wireless USB Adapter.
On a computer already configured
to use the USB Bluetooth adapter,
the Found New Hardware Wizard
appears when you plug the USB
Bluetooth adapter into the USB port.
The Found New Hardware Wizard appears if you unplug
an already configured USB Bluetooth wireless adapter
from your computer and then plug it into a different USB
port on the same computer (for example, if you move the
adapter from your laptop to your docking station).
When the Found New Hardware Wizard appears:
1. Click Install the software automatically
(Recommended), and click Next. The wizard
reconfigures the computer to use the adapter on the
new USB port.
2. Click Finish.
When you try to connect to the BTCVT
device with your laptop, this error
message appears:
The COM1 connection failed.
Could not connect to remote
device.
You are unable to pair or maintain
pairing with your BTCVT device.
The Bluetooth driver for the laptop is not fully compatible
with the BTCVT device. Contact your network help desk
for assistance or go to the manufacturer’s website to
download a compatible driver. Remove the old drivers
before you install the new drivers.
Metasys® CCT Bluetooth® Technology Communication Commissioning Guide8
Tabla de contenidos
Otros manuales de Convertidor de medios de Johnson Controls
Johnson Controls
Johnson Controls CWCVT Manual de usuario
Johnson Controls
Johnson Controls tyco PG8WLSHW8 Manual de usuario
Johnson Controls
Johnson Controls FX-BTCVT Manual de usuario
Johnson Controls
Johnson Controls FX-BTCVT Series Manual de usuario
Johnson Controls
Johnson Controls Tyco PowerG PG8HRDW8 Manual de usuario
Johnson Controls
Johnson Controls AS-CVTPROx00-1 Manual de usuario
