JL Audio StealthMod SMS-B-X5E70 Manual de usuario

INSTALLATION GUIDE

for the

SMS-B-X5E70

SKU# 94518

2007 - Up

Thank you for choosing a JL Audio StealthMod®for your automotive sound system. With

proper installation, your new vehicle-specific enclosed subwoofer system will deliver

years of listening pleasure.

We strongly recommend that you have your new StealthMod®system installed by your

authorized JL Audio dealer. The installation professionals employed by your dealer have

the necessary tools and experience to disassemble and reassemble your vehicle properly.

Also, keep in mind that your warranty coverage extends to 2 years if your system is

installed or approved by your authorized JL Audio dealer. If you prefer to perform your

own installation, please read this installation guide completely

before beginning the process.

If you choose to perform the installation yourself, it is absolutely vital that the

StealthMod®system be properly mounted to the vehicle according to these

instructions. Failure to mount the enclosure properly presents two problems:

1) The sub-bass performance will suffer due to the movement of the enclosure

caused by the force exerted by the woofer(s).

2) A loose enclosure presents a serious safety hazard in the event of a collision

or sudden deceleration.

STEP 1

Roll down the window and open the passenger door.

Continued on Next Page

STEP 2

Carefully pry up on the trim piece around the release handle

and remove it from the vehicle.

STEP 3

Remove the screw behind the panel.

SMS-B-X570 INSTR_SKU# 11339

INSTALLATION

DIFFICULTY:

OUT

ESTIMATED TIME:

45 HOURS

StealthMod ®

Continued on Next Page

SMS-B-X5E70 INSTR_SKU#11339

STEP 7

With the door panel removed, unclip the front of the upper

door trim as shown.

STEP 6

Remove the two screws on the underside of the door panel.

Starting at the bottom, unclip the door panel from the door,

unplug the wiring harnesses, and remove the door panel

from the vehicle.

STEP 5

Remove the two screws under the panel.

STEP 4

Carefully pry off the trim on the pull handle and remove it

from the vehicle.

Page 2 • JL Audio, Inc 2012

STEP 9

Pictured is the back side of the door panel. Cut a small

piece of the Foam Tape and apply it to the panel as shown.

Remove the screw indicated, and retain it for use in Step 11.

STEP 11

Slide a pair of Speed Clips over the holes in the Crossover

Bracket. Place the bracket over the two pieces of Foam

Tape, aligning the holes with the clip and speaker mounting

hole. Secure the bracket to the door panel with the screw

removed in Step 9.

STEP 10

Cut a second piece of the Foam Tape and apply it to the

panel, over the clip as shown.

STEP 8

Unclip the rear of the upper door trim as shown, and remove

the panel from the vehicle.

Continued on Next Page

SMS-B-X5E70 INSTR_SKU#11339

STEP 15

Reinstall the upper door trim with the tweeter wires exiting

from the bottom as shown. Extend the positive and

negative tweeter wires as necessary, and onnect them to the

Tweeter Output (T+ and T-) of the Crossover.

Plug in the factory harnesses and reinstall the door panel.

STEP 14

Mount the C5 Tweeter into the surface mount cup, and

install the assembly into the factory provision as shown. An

adhesive is recommended to secure the assembly. Reinstall

the foam with the tweeter wires exiting from the bottom.

STEP 13

Remove the foam from the upper door trim to access the

factory tweeter. Unclip and remove the tweeter.

STEP 12

Cut two more pieces of Foam Tape, and apply them to the

Crossover Bracket, then mount the Crossover to the bracket

using a pair of #8 x 3/4” Phillips Head Screws.

Cut the factory midrange wires with enough length to reach

the Crossover. Connect the White positive and White/Blue

negative wires from the factory midrange to the Woofer

Output (W+ and W-) of the Crossover. Connect the other

end of the cut factory midrange wires to the Input (In + and

In -) of the Crossover.

Page 3 • JL Audio, Inc 2012

STEP 17

Empty out the cargo area so that you have a clean area to

work in.

STEP 19

The tools can be relocated to the foam tray inside the spare

tire.

STEP 18

Remove the cargo floor panel. Remove the two screws on

the battery cover, and remove the cover. Remove the screw

holding in the storage tray, and remove the tray.

STEP 16

Repeat the Crossover and Tweeter installation for the driver’s

side beginning by following the procedure outlined in Steps

1-3.

Remove the screw from inside the door cup, and

carefully unclip the switch panel as shown. Unplug the

harnesses and remove the panel.

Continue by following the procedure outlined in Steps

6-15. The factory midrange has a Yellow positive wire and a

Yellow/Black negative wire.

Continued on Next Page

SMS-B-X5E70 INSTR_SKU# 11339

STEP 23

Remove the speed clip from the location indicated by the

left arrow, and relocate it to the location indicated by the

right arrow as shown.

STEP 22

Using a 1” hole saw, drill a hole at the intersection and slide

a U-Nut through the driled hole, aligning it with the factory

hole as shown.

STEP 21

Note: Steps 21-22 are only necessary on vehicles not

equipped with the factory bracket shown in Step 20.

Locate the two holes in the floor, and mark their

perpindicular intersection as shown.

STEP 20

Remove the nut from the factory bracket as shown. Retain

the nut for use in Step 26.

If this factory bracket isn’t present, substitute Steps 21-22.

Page 4 • JL Audio, Inc 2012

STEP 25

Using a pair of 1/4” - 20 x 1” Bolts, 1/4” Lock Washers, and 1/4”

Flat Washers, attach the Side Bracket to the Stealthbox® as

shown, and hand tighten.

STEP 26

Attach 12 AWG Speaker Cable to the Stealtbhox®, and place

the enclosure into position, aligning the hole in the Side

Bracket with the factory bolt as shown. Secure the Side

Bracket to the floor using the factory nut removed in Step

20.

On vehicles not equipped with the factory bracket and bolt,

secure the Side Bracket to the U-Nut installed in Step 22

using a 1/4 - 20 x 1/2” Bolt.

STEP 24

Pictured is the included hardware needed to mount the

enclosure, along with the factory nut removed from Step 20.

STEP 27

Slide the Stealthbox® as far back toward the rear of the

vehicle as possilbe. Using an open-ended wrench, tighten

the two 1/4” - 20 x 1” Bolts to secure the Side Bracket to the

Stealthbox®.

Continued on Next Page

SMS-B-X5E70 INSTR_SKU#11339

STEP 31

Remove the three clips that hold the storage pocket in place

and remove the pocket.

STEP 30

Remove the access door from the left side panel.

STEP 29

Secure the Top Bracket to the Stealtbox® and to the rail using

a pair of 1/4” - 20 x 1” Bolts, 1/4” Lock Washers, and 1/4” Flat

Washers.

STEP 28

Slide a U-Nut over the factory hole in the rail as indicated.

Page 5 • JL Audio, Inc 2012

STEP 33

Pictured is the cargo area with the left side panel removed.

Unplug the indicated factory amplifier plug for easier access

to the factory wiring in Steps 37-38.

STEP 34

Place four Speed Clips on the Amplifier Bracket as shown.

STEP 32

Remove the three clips that hold the side panel in place and

remove the panel.

STEP 35

Align the Amplifier Bracket to the factory studs as shown,

and secure it to the vehicle using three 5mm Hex Nuts as

indicated.

Continued on Next Page

SMS-B-X5E70 INSTR_SKU#11339

STEP 39

Extend the red ignition wire from the CL-SSI using the

supplied Remote Turn-on Wire, route it to the passenger side

of the cargo area, and connect it to the factory ignition wire

on the back of the accessory outlet. It’s recommended to

fuse the wire within a few inches of the connection.

Connect the yellow 12 volt power wire, the black ground

wire, and the blue remote turn-on wire of the CL-SSI to the

XD700/5 along with the main Red Power Wire and Black

Ground Wire as indicated on the amplifier.

STEP 38

Using the wire colors indicated in Step 37 as a guide,

connect the door wires from the factory amplifier plug to

the Input A of the CL-SSI. Connect the sub wires to the Input

B of the CL-SSI. Using the Speaker to RCA adapters and RCA

cables, connect the front outputs of the CL-SSI to the Inputs

1-2 of the XD700/5, and the rear outputs of the CL-SSI to

Inputs 3-4 of the XD700/5.

Extend the opposite side of the factory wires with 16 AWG

Speaker Cable as necessary, and connect the door wires

to Outputs 1-2 on the XD700/5. Connect the sub wires to

Outputs 3-4 on the XD700/5.

STEP 37

Cut the following factory wires approximately six inches

away from the factory amplifier plug:

LF Door (+) = Blue/Brown RF Door (+) = Blue/Brown

LF Door (-) = Blue/White RF Door (-) = Blue/Black

LF Sub (+) = Brown/Yellow RF Sub (+) = Brown/White

LF Sub (-) = Red/White RF Sub (-) = Red/Blue

Note: Pictured are plugs we added to easily return the

vehicle to its original condition. These are not necessary, nor

included with this StealthMod® kit.

STEP 36

Slide a Speed Clip over the factory hole as shown, and secure

the lower part of the bracket with a #8 x 3/4” Phillips Head

Screw.

Page 6 • JL Audio, Inc 2012

STEP 41

Route the Ground Wire to the factory ground location

indicated, and secure it using the factory bolt.

STEP 42

Route the Power Wire toward the battery. Connect the Fuse

Holder within 12” of the battery, and secure the the Power

Wire to the positive battery post. Install the Fuse into the

Fuse Holder.

STEP 40

Connect the 12 AWG Speaker Cable from the Stealthbox® to

output 5 on the XD700/5. Mount the amp to the Amplifier

Bracket using four #8 x 1” Phillips Head Screws. Plug in the

cable for the HD-RLC and route it to the desired level control

location. Follow the steps included with the HD-RLC for

mounting instructions.

STEP 43

Secure the CL-SSI with Velcro as shown. Be sure to leave it

accessible for adjusting the trim levels

Continued on Next Page

SMS-B-X5E70 INSTR_SKU#11339

STEP 47

Cut the Foam Tape into three 4” strips, affix them to the new

Battery Cover, and trim away the excess as shown.

STEP 46

Adjust the trim levels on the CL-SSI as outlined in its owner’s

manual. Set the amplifier crossover controls as shown in

the illustration at the end of this manual, and set the input

sensitivites on the amplifier as outlined in its owner’s manual.

Reinstall the side panel.

STEP 45

Reinstall the storage pocket.

STEP 44

Cut away the portion of the storage pocket indicated by the

tape.

Page 7 • JL Audio, Inc 2012

CONGRATULATIONS!

You have completed the installation for this model!

Enjoy your new StealthMod®!

STEP 48

Secure the Battery Cover using the three #8 x 1” Sheet Metal

Screws. Reinstall the floor panel.

SMS-B-X5E70 INSTR_SKU#11339

Page 8 • JL Audio, Inc 2012

INCLUDED HARDWARE

(1) 1/4 - 20 x 1/2” Bolt (4) #8 x 1” Phillips Head Screw (1) 12’ Blue Remote Wire

(4) 1/4 - 20 x 1” Bolt (3) #8 x 3/4” Phillips Head Screw (1) 6’ 12 AWG Speaker Wire

(4) 1/4” Flat Washer (9) Speed Clip (1) 12.5’ 16 AWG Speaker Wire

(4) 1/4” Lock Washer (1) Velcro

(2) 1/4 - 20 U-Nut (1) XD700/5

(1) Battery Cover (1) C5-075ct

(3) #8 x 1” Sheet Metal Screw (2) C5-525-XO

(1) Top Bracket (1) CL-SSI

(1) Side Bracket (1) XD-MFB-MAXI

(1) Foam Tape (1) XD-MAXI-60

(1) Amp Bracket (2) XD-CLRAIC2-3

(3) 5mm Hex Nut (2) XD-CLRAIC2-SW

(1) Left Crossover Bracket (1) 6’ Red Power Wire

(1) Right Crossover Bracket (1) 6’ Black Ground Wire

SPECIFICATIONS

Enclosure Type: Acoustic Suspension (sealed)

Driver Type: 10W3v3-2

Nominal Impedance: 2 ohm

Continuous Power Handling: 500 watts

POWER RECOMMENDATION

The diagram below shows the recommended crossover settings for the XD700/5.

The XD700/5 is a very versitile amplifier. Consult the owner’s manual for even more detailed

information about installing and tuning the amplifier.

All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, “Stealthbox” and the Stealthbox logo are registered

trademarks of JL Audio, Inc.“Ahead of the Curve” and its respective logo is a trademark of JL Audio, Inc.

#6,294,959 #6,501,844 #6,496,590 #6,441,685 #5,687,247 #6,219,431 #6,625,292 #D472,891 #D480,709 Other U.S. & Foreign patents pending.

For more detailed information please visit us online at www.jlaudio.com.

(954) 443-1100

www.jlaudio.com

10369 NORTH COMMERCE PARKWAY • MIRAMAR, FLORIDA • 33025 • USA

Otros manuales de Sistema estéreo para automóvil de JL Audio

JL Audio

JL Audio Stealthbox SB-GM-C7CP1 Manual de usuario

JL Audio

JL Audio SB-F-MUCONV2/13W6V2 Manual de usuario

JL Audio

JL Audio Stealthbox SB-B-7SER/10W6v2 Manual de usuario

JL Audio

JL Audio Stealthbox SB-GM-CLREXT/10W3v3 Manual de usuario

JL Audio

JL Audio Stealthbox 94460 Manual de usuario

JL Audio

JL Audio XR525-CSi Manual de usuario

JL Audio

JL Audio SB-CAN-MVCM1/10TW3 Manual de usuario

JL Audio

JL Audio Stealthbox SB-CAN-G2MVX3D/10TW3 Manual de usuario

JL Audio

JL Audio Stealthbox SB-VW-JETNCS/10W1v2 Manual de usuario

$JL Audio Stealthbox SB-B-3SER/CPE/SDN(E90\92) Manual de usuario$

JL Audio

JL Audio Stealthbox SB-B-3SER/CPE/SDN(E90\92) Manual de usuario

JL Audio

JL Audio Stealthbox SB-B-X5/10W1v3 Manual de usuario

JL Audio

JL Audio Stealthbox SB-D-TRKCTR/12W3v2 Manual de usuario

JL Audio

JL Audio Stealthbox SB-F-150-SPRCRW/13TW5v2 Manual de usuario

JL Audio

JL Audio Stealthbox SB-F-TRKCTR/10W3 Manual de usuario

JL Audio

JL Audio Stealthbox SB-GM-4GSUVCNSL/10TW1 Manual de usuario

JL Audio

JL Audio Stealthbox SB-D-DRNGO/10W0 Manual de usuario

JL Audio

JL Audio C3-650 Manual de usuario

JL Audio

JL Audio stealthbox SB-POL-ACE/10TW1 Manual de usuario

JL Audio

JL Audio Stealthbox SB-F-150-SCDBL/12TW3 Manual de usuario

JL Audio

JL Audio MediaMaster 105 Manual de usuario

JL Audio

JL Audio Stealthbox SB-D-MAG/10W3v3 Manual de usuario

JL Audio

JL Audio Stealthbox SB-F-FOC5DR/10TW3 Manual de usuario

JL Audio

JL Audio Stealthbox SB-D-CLBR/10W1v2 Manual de usuario

JL Audio

JL Audio Stealthbox SB-D-MGACAB/10W6v3 Manual de usuario

Manuales populares de Sistema estéreo para automóvil de otras marcas

Clarion

Clarion PU-9836A Manual de usuario

Sony

Sony MEX-BT5750U Manual de usuario

Mitsubishi Electric

Mitsubishi Electric AR0M Manual de usuario

Sony

Sony RM-X7BT Manual de usuario

Insignia

Insignia NS-HD5113 Manual de usuario

Clarion

Clarion BTD3341 Manual de usuario

USA SPECS

USA SPECS PA11-VW6 Manual de usuario

Sony

Sony MEX-N4380BT Manual de usuario

Kenwood

Kenwood KCD-BT6544U/UY Manual de usuario

JVC

JVC KD-DB912BT Manual de usuario

Philips

Philips CSQ405/98 Manual de usuario

Alpine

Alpine TDM-7544 Manual de usuario

Autotek

Autotek TransAm TA 1400 Manual de usuario

Clarion

Clarion PN-3124N-A Manual de usuario

Denso TEN

Denso TEN FT0108A Manual de usuario

Pyle

Pyle PLD57MU Manual de usuario

Harman

Harman Chrysler Radio Navigation System RB4 Manual de usuario

Clarion

Clarion VS735 Manual de usuario